Search Results

Cyclic oligomers of butylene terephthalate (CBT™)† represent a new chemical route to semi-crystalline thermoplastic polybutylene terephthalate (PBT). The oligomers of interest melt completely at about 150°C to produce a low viscosity fluid that is ideal for wetting and dispersing fibrous fillers and reinforcements thereby enabling the development of composites that were previously not possible when working with high viscosity commercial PBT. Introduction of catalyst to undiluted molten cyclic oligomer leads to rapid ring opening polymerization and the formation of high molecular weight thermoplastic PBT without the generation of volatile organic compounds. The polymer resulting from this polymerization will be hereby referred to as pCBT. Treatment of cyclic oligomers in this fashion results in pCBT thermoplastic resin with a high melting point (230°C) and physical performance similar to that of other commercially available PBT resins.

The coupling is an integral part of the Cummins CELECT electronically controlled injector. Excessive wear was observed on early designs of the coupling and coupling bore. The coupling wear was caused by a high stress concentration and excessive side loading of the coupling as it slid against the coupling bore. The zero wear theory was used to develop a coupling design where the maximum wear depth does not exceed half the peak to peak surface finish (zero wear) over the life of the engine. The side load exerted on the coupling was compared with the calculated contact pressure for zero wear. The undesirable effects of a square edge stress concentration are discussed in the zero wear model. The physical effects of the sharp edge and chamfered coupling edge are reported, but not analyzed in this paper. Three different coupling designs were investigated by applying the zero wear concept.

The hazardous bulk chemical liquid cargo transportation is usually made through highways, using special automotive devices, named semitrailer tank, a kind of mobile tank specially developed to perform this task, manufactured with many types of steel, selected according to the chemical characteristics of the product to be transported. Equipment sizing is made based on specific standards which include specified formulas, loading, and safety factors representing the design criteria of this type of device. Despite of the detailed design criteria for semitrailer tank, it has been observed failure of some pieces of equipment during operation, in a shorter effective life than that one considered in the design phase itself. Considering a detailed study of the stress distribution in this type of equipment, this paper shows a verification of the possibility of yielding failure in the semitrailer tank structure.

All around the world, steps are being taken to improve the quality of our environment. Prominent among these are the definition, implementation, and attainment of increasingly stringent emissions regulations for all types of engines, including off-highway diesels. These rigorous regulations have driven use of technologies like after-treatment, advanced air systems, and advanced fuel systems. Fuel dispensed off-highway is routinely and significantly dirtier than fuel from on-highway outlets. Furthermore, fuels used in developing countries can be up to 30 times dirtier than the average fuels in North America. Poor fuel cleanliness, coupled with the higher pressures and performance demands of modern fuel systems, create life challenges greater than encountered with cleaner fuels. This can result in costly disruption of operations, loss of productivity, and customer dissatisfaction in the off-highway market.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.8 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.

This report is concerned with the effects of braid angle on the behavior of hydraulic hose. For equilibrium conditions to exist, and if the braid layers are assumed to bear tension forces only, the angle of the reinforcement layers must be along that of the total force exerted by the internal pressure. This is the neutral angle θN, which has a theoretical value of 54.74° (54°44′). It is possible to hypothesize a fretting wear model in which wires move on top of one another inside a braid layer if the braid angle is different from this theoretical neutral angle. Even though theoretical claims are made by some technical professionals, the hydraulic hose industry has been successfully making hoses with non-neutral braid angles for years. Testing and application have shown that fretting wear is not a principal cause of hose failure and fatigue.

SINCE 1954 the CIMTC Subcommittee has been engaged in a program to meet military requirements through industry's production of construction equipment which can give satisfactory cold weather performance down to temperatures of −65 F. Individual contracts for three crawler tractors and one motor grader were negotiated by ERDL for these projects, and their performance is discussed. Industry participation was subsequently expanded to include engineering tests in the cold weather conditions of the Mesabi Iron Range. This joint report of the Winterization Sub-committee of the CIMTC and ERDL Winterization Section consists of separate papers by various members and consultants of this Sub-committee and ERDL personnel.

Cast iron is generally thought of as a weak, dirty, cheap, brittle material that does not have a place in applications requiring high strength and defined engineering properties. While gray cast iron is relatively brittle by comparison with steel, ductile iron is not. In fact, ductile iron has strengths and toughness very similar to steel and the machinability advantages make an attractive opportunity for significant cost reductions. Gray and ductile iron bar stock is commercially available and can be used as a direct replacement in applications that are currently being made from carbon steel bar. Ductile iron bar stock conversions are very prevalent in many fluid power applications including glands and rod guides, cylinders, hydrostatic transmission barrels and in high-pressure manifolds. Automotive gears are being converted to ductile iron for its damping capacity and cost reductions.

Find out why you should attend the 2025 Noise and Vibration Conference and Exhibition.

In selecting springs for commercial vehicles, it is essential to consider the fundamental principles of the suspension system as a whole, as well as the specific spring characteristics. This paper discusses the applications of these principles; also, it compares the many types of springs available, including single leaf, multileaf, and two-stage leaf springs, and coil, rubber, and pneumatic springs. Among the considerations stressed are: the relationships of spring static deflections to vehicle pitch frequency and oscillation center location, the questionability of two-stage leaf springs, the disadvantages of single tapered leaf versus multi-leaf springs, the advantages of coil springs in low weight and variable rate, and why pneumatic springs are ideal for large load range, heavy commercial vehicles.

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. For bolt together military wheels, see SAE J1992. This document does not cover other special application wheels and rims.

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. For bolt together military wheels, see SAE J1992. This document does not cover other special application wheels and rims.

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use by trucks, see SAE J267. For wheels intended for normal highway use by passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.

This SAE Recommended Practice provides minimum performance target and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. Users may establish design criteria exceeding the minimum performance target for added confidence in a design. The cycle target noted in Tables 1 and 2 are based on Weibull statistics using two parameter, median ranks, 50% confidence level and 90% reliability, and beta equal to two, typically noted as B10C50. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. For bolt together military wheels, refer to SAE J1992. This document does not cover other special application wheels and rims.

This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. Users may establish design criteria exceeding the minimum performance requirement for added confidence in a design. The cycle requirements noted in Tables 1 and 2 are based on Weibull statistics using 2 parameter, median ranks, 50% confidence level and 90% reliability, and beta equal to 2, typically noted as B10C50. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. For bolt together military wheels, see SAE J1992. This document does not cover other special application wheels and rims.

The SAE Recommended Practice establishes minimum performance requirements and related uniform laboratory test procedures for evaluating lateral (curb) impact collision resistance of all wheels intended for use on passenger cars and light trucks.

Wheel hubs with drum brakes of heavy-duty vehicles rarely broke, but some suddenly cracked in the 2000s. The cause of damage was said to be a lack of hub strength. However, the case was suspicious because the hubs were produced according to the design guidelines by the JSAE. In the 1990s, brake shoe-lining materials were changed from asbestos to non-asbestos for people’s health. The brake squeal and abnormal self-lock frequently occurred because of the increased friction coefficient between drum and shoe lining in the case of the leading–trailing type. The mechanical friction coefficient changes with the material and the contact angle, which varies with the wear of shoe lining and the drum temperature. In the previous report, the deformation of the wheel hub under the abnormal self-lock was verified by observing the change of hub attitude in model test equipment.

In Automotive, Steel wheels are exponentially replaced by Aluminum wheels because of its feather light, agile performance and better acceleration. One such widely used size is 11.75 x 22.5 wheels for trucks and trailer segment. During the design stage of 11.75 x 22.5 wheel, the valve hole was placed away from the stress concentration zone to reduce the stress on the holes and also the design was validated through all conventional wheel rim testing methodologies (Like CFT, RFT and Bi-axial) and the wheel passed all the test requirements. During the field trials, failures were observed on the valve holes, despite of this hole was away from stress concentration region. Understood from the field trials that, the regular testing was not able to simulate the real field conditions for this particular size and changed the boundary condition in our FEA to simulate the actual conditions. After changing the boundary conditions, we could able to observe more stress in valve hole.