Search Results

Cast iron is generally thought of as a weak, dirty, cheap, brittle material that does not have a place in applications requiring high strength and defined engineering properties. While gray cast iron is relatively brittle by comparison with steel, ductile iron is not. In fact, ductile iron has strengths and toughness very similar to steel and the machinability advantages make an attractive opportunity for significant cost reductions. Gray and ductile iron bar stock is commercially available and can be used as a direct replacement in applications that are currently being made from carbon steel bar. Ductile iron bar stock conversions are very prevalent in many fluid power applications including glands and rod guides, cylinders, hydrostatic transmission barrels and in high-pressure manifolds. Automotive gears are being converted to ductile iron for its damping capacity and cost reductions.

Wear characteristics of four bearing materials have been investigated under different sliding conditions. The bearing materials used were CDA 954, CDA 863, CDA 932, and CDA 938. Using a Taber Wear Tester, a cylinder on a flat geometry was used as a tribo contact pair. All bearing materials in the form of a thick cylindrical disk were subjected to combined sliding-rolling motion against a rotating flat disk. The flat disk was either an abrasive disk, or a very soft steel disk, or a hardened steel disk with and without lubrication. Wear was measured as weight loss after several thousand cycles of rotation. Maximum wear of the bearing materials occurred when the counter body was a very soft steel disk. These results together with the wear rate of each bearing material sliding against four different counter bodies are presented. These results are found to be of practical importance in the design and application of journal bearings made of materials used in this investigation.

Axial piston type pumps are often exposed to severe operating conditions because of the duty cycle, the environment, or, in some situations, poor maintenance and even abuse. The detrimental effects on the pump and the hydraulic system as a result of these adverse conditions are often not known or predictable. In this study, four controlled severe operating conditions were imposed on four identical axial piston type pumps. They included 1) constant high load pressure and normal fluid temperature, 2) constant high load pressure and elevated fluid temperature, 3) cyclic load pressure and normal fluid temperature, and 4) cyclic load pressure and elevated fluid temperature. The tests were long-term; they were run continuously for up to 5000 hours. The pump wear was monitored in all cases using ferrography. In addition, the condition of the fluid was monitored and the circuit filters were examined periodically. The results of the findings are presented in this paper.

This paper is concerned with the synergistic effects of pump wear modes. The objective is to investigate the wear produced by cavitation, adhesion, abrasion, and corrosion and to verify a proposed model of the synergistic pump wear process. The approach followed includes identification of the combined effects of different wear modes (synergisms) in a pump and the development of a synergistic wear model that includes pump operating and environmental conditions as trigger factors of wear modes. An experimental program was designed to evaluate the cavitation, adhesion, and corrosion wear effects in conjunction with the abrasive wear produced in a pump by measuring wear debris, particle size and gravimetric levels of fluid. The generation of wear was traced to different pump locations. The results obtained here suggest that improved pump design and longer pump service life can be obtained when synergisms between failure modes are properly understood.

Hydraulic fluid performance, including water-glycols (W/G), is dependent on the chemical composition of the fluid and cleanliness. An overview of W/G fluid chemistry on pump wear is provided here. Also provided, is a brief overview of the impact of fluid cleanliness on the potential wear properties of various components. Finally, an overview of recommended analytical procedures to assure adequate long-term fluid hydraulic and lubrication performance is provided. If these procedures are followed, substantial improvements in hydraulic pump longevity and performance will be realized.

One of the most commonly used tests to evaluate the antiwear properties of a hydraulic fluid is ASTM D 2882 which is based on a Vicker's V-104 vane pump. Although this is a commonly used test, the results are subject to numerous potential problems in both testing procedure and pump hardware. In this paper, the particular focus will be placed on potential problems that may be encountered with testing of water-glycol hydraulic fluids which may lead to erroneous and non-reproducible results.

This standard specifies a procedure for approximating the volume of materials contained in the grapple of bucket linkage operated grapples mounted to excavators. The volume ratings are based on the inside dimensions of the grapple and representative volumes extending beyond the grapple. The method employs the technique of dividing the complex shape of the material in the grapple into simple geometric forms to allow volume calculations of different grapple configurations. The rating method is intended to provide a consistent means of comparing grapple capacities. It is not intended to define actual capacities that might be observed in any specific application.

After many years of successful Visco fan drive applications, Behr has now transferred the Visco technology to the coolant pump drive. The continuously variable Visco drive allows the coolant pump to deliver the optimum flow dependent upon the requirements, therefore reducing the drive power to the minimum possible. Up to now coolant pumps, world wide, have almost always been powered by direct, uncontrolled drives. Consequently, the delivery and the power consumption have been directly related to the engine speed, which, in many conditions, results in an unnecessarily high flow rate. The potential to reduce the flow rate is inherent within the Visco coolant pump. As a concept with continuous control of the impeller speed it has been found to be more fuel efficient than incremental impeller speed control or concepts which only restrict or divert the flow rate. The torque transmission via the shear forces of a silicone oil results in a robust and wear-free drive unit.

Cylinder pressure-based combustion control is widely introduced for passenger cars. Benefits include enhanced emission robustness to fuel quality variation, reduced fuel consumption due to more accurate (multi-pulse) fuel injection, and minimized after treatment size. In addition, it enables the introduction of advanced, high-efficient combustion concepts. The application in truck engines is foreseen, but challenges need to be overcome related to durability, increased system costs, and impact on the cylinder head. In this paper, a new single cylinder pressure sensor concept for heavy-duty Diesel engines is presented. Compared to previous studies, this work focuses on heavy-duty Diesel powertrains, which are characterized by a relatively flexible crank shaft in contrast to the existing passenger car applications.

This paper outlines the design philosophy and evaluation of the new “H” series variable displacement, medium pressure, open-circuit, axial piston hydraulic pumps. The “H” series is based on previously existing, technically successful, rotating group designs, but has significant design improvements affecting the areas of: Unit Weight Envelope Size Ease of Assembly, Disassembly, Repairability and Modification Alternate Fluid Capabilities The “H” series is a family of naturally aspirated pumps nominally rated at 250 or 275 bar (3625 or 4000 psig), depending on system operating parameters. The geometric displacements of the four units in the series are as follows: 57cc (3.5 cu. in./rev.) 74cc (4.5 cu. in./rev.) 98cc (6.0 cu. in./rev.) 131cc (8.0 cu. in./rev.)

Hydraulic pump wear reduces machine performance, causes secondary damage, and may be a precursor for catastrophic failure. A noninvasive diagnostic that can determine the level of pump wear while the pump is on the machine would reduce the costs of owning and operating a hydraulic system. Wear that changes the vibration characteristics of the pump can be observed with an accelerometer attached to the pump's case. A series of tests were performed and diagnostic algorithms were developed. Prediction accuracy as high as 97.9% in classifying pumps as having above or below 10% flow loss was achieved.

The SAE J1939 communications network is developed for use in heavy-duty environments and suitable for horizontally integrated vehicle industries. The SAE J1939 communications network is applicable for light-duty, medium-duty, and heavy- duty vehicles used on-road or off-road, and for appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to, on-highway and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. SAE J1939-71 Vehicle Application Layer is the SAE J1939 reference document for the conventions and notations that specify parameter placement in PGN data fields, the conventions for ASCII parameters, and conventions for PGN transmission rates. This document previously contained the majority of the SAE J1939 data parameters and messages for information exchange between the ECU applications connected to the SAE J1939 communications network.

The SAE J1939 communications network is developed for use in heavy-duty environments and suitable for horizontally integrated vehicle industries. The SAE J1939 communications network is applicable for light-duty, medium-duty, and heavy-duty vehicles used on-road or off-road, and for appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to, on-highway and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements. SAE J1939-71 is the SAE J1939 reference document for the conventions and notations used to specify the parameter (SP) placement in PG data, the conventions for ASCII parameters, and conventions for PG transmission rates. This document previously contained the majority of the SAE J1939 OSI application layer data parameters and messages for information exchange between the ECU applications connected to the SAE J1939 communications network.

A variable swirl inlet system with swirl control subport was developed with consideration of how to control the angular momentum of inlet flow into the cylinder. The effects of swirl on direct injection diesel engine performance and emissions are investigated with this variable swirl system. Basically, lower swirl level reduces the amount of initial stage burning, which is related to NOx emission, maximum cylinder pressure and rate of cylinder pressure rise, over the entire range of engine speed and load. As a result, in high speed range or partial load range, low swirl level simultaneously gives better BSFC and lower NOx level. An intercooled turbocharged engine with this variable swirl inlet system gave higher low-speed torque, higher brake horse power and better cold startability by selection of optimum swirl level for each engine condition.

The paper presents the development of a novel approach to the solution of detailed chemistry in internal combustion engine simulations, which relies on the analytical computation of the ordinary differential equations (ODE) system Jacobian matrix in sparse form. Arbitrary reaction behaviors in either Arrhenius, third-body or fall-off formulations can be considered, and thermodynamic gas-phase mixture properties are evaluated according to the well-established 7-coefficient JANAF polynomial form. The current work presents a full validation of the new chemistry solver when coupled to the KIVA-4 code, through modeling of a single cylinder Caterpillar 3401 heavy-duty engine, running in two-stage combustion mode.

Reactivity Controlled Compression Ignition (RCCI) natural gas/diesel dual-fuel combustion has been shown to achieve high thermal efficiency with low NOX and PM emissions, but has traditionally been limited to low to medium loads. High BMEP operation typically requires high substitution rates (i.e., >90% NG), which can lead to high cylinder pressure, pressure rise rates, knock, and combustion loss. In previous studies, compression ratio was decreased to achieve higher load operation, but thermal efficiency was sacrificed. For this study, a multi-cylinder heavy-duty engine that has been modified for dual-fuel operation (diesel direct-injection and natural gas (NG) fumigated into the intake stream) was used to explore RCCI and other dual-fuel combustion modes at high compression ratio, while maintaining stock lug curve capability (i.e., extending dual-fuel operation to high loads where conventional diesel combustion traditionally had to be used).

New high torque electric clutches have been developed which have a single direct mounting pad for pumps manufactured to SAE J744C. These clutches, available in both belt and shaft driven versions, offer the opportunity for considerable improvement to be made in vehicle productivity and fuel efficiency.

To increase productivity a new concept of proportional pressure, flow and control cartridges have been developed to enhance vehicle operation at a reasonable cost. Actuators have also been developed to stroke directional valves, or piston pumps and motors. These low power consumption devices readily interface with microprocessors. Engineers have been looking for new generations of electrohydraulic valves which will increase operator performance by simplifying the operation of vehicles with automatic controls where possible plus eliminating the brute strength manual type valving to decrease operator fatigue. Maintenance has always been a severe set back to productivity. By utilizing effective yet efficient cartridge proportional valves that are designed for simplicity of use and repair, drastic savings are shown. Previous designs were bulky and very contamination sensitive. They did the job, but were both expensive and had very high maintenance levels.