Search Results

Enhanced SATCOMs for Unmanned Aerial Systems The Bus Too Tough to Die Combating Infrared Threats on the Battlefield Optical Interconnect Design Challenges in Space High-Performance Computing for the Next-Generation Combat Vehicle Merging Antenna and Electronics Boosts Energy and Spectrum Efficiency Integrated Magneto-Optical Devices for On-Chip Photonic Systems Development of magneto-optical (MO) materials could lead to a range of nonreciprocal optical devices for emerging standardized photonic integrated circuit (PIC) fabrication processes. Low Power Optical Phase Array Using Graphene on Silicon Photonics Electrostatic doping of 2D materials embedded in waveguides could enable ultrafast devices with unprecedented power. Spatial Resolution and Contrast of a Focused Diffractive Plenoptic Camera New technology captures spectral and spatial information of a scene in one snapshot while raising pixel counts and improving image quality.

Beyond VMEbus - A New Concept Taming the Thermal Behavior of Solid-State Military Lasers Solving the Challenge of Thermal Design in Aerospace Electronics Improving Component Life in Abrasive, Corrosive Aerospace Environments New Pulse Analysis Techniques for Radar and EW Validation of Ubiquitous 2D Radar Converting Existing Copper Wire Firing System to a Fiber-Optically Controlled Firing System for Electromagnetic Pulsed Power Experiments Technological improvements make pulsed-power experiments with gunpowder- or air-driven guns safer. Low-Cost Ground Sensor Network for Intrusion Detection COTS-based system could provide increased level of security with less manpower. In-Network Processing on Low-Cost IoT Nodes for Maritime Surveillance Commercially available system of distributed wireless sensors could increase the Navy's intelligence collection footprint.

Abstract TOC

Engineering Events staff at SAE International in Warrendale, Pennsylvania, have extended the call for abstracts through September 21 for the organization’s AeroTech aerospace and defense technology conference, which will take place at the Fort Worth Convention Center in Fort Worth, Texas, March 14-16, 2023. Visit the AeroTech call for abstracts page for more information and to get started.

Success in metal additive manufacturing (AM) relies on the optimization of a large set of process parameters to achieve materials whose properties and performance meet design and safety requirements. Despite continuous improvements in the process over the years, the quality of AM parts remains a major concern for manufacturers. Today, researchers are starting to move from discrete geometry-dependent build parameters to continuously variable or dynamically changing parameters that are geometry- and scan-path aware. This approach has become known as “feedforward control.” Process Control for Defect Mitigation in Laser Powder Bed Fusion Additive Manufacturing discusses the origins of feedforward control, its early implementations in AM, the current state of the art, and a path forward to its broader adoption. Click here to access the full SAE EDGETM Research Report portfolio.

This Aerospace Standard (AS) establishes the requirements for suppliers of Nonconventional Machining Services to be accredited by the National Aerospace and Defense Contractors Accreditation Program (NADCAP). NADCAP accreditation is granted in accordance with SAE AS7003 after demonstration of compliance with the requirements herein. The requirements may be supplemented by additional requirements specified by the NADCAP Nonconventional Machining and Surface Enhancement (NMSE) Task Group. Using the corresponding Audit Criteria (PRI AC7116) will ensure that accredited Nonconventional Machining suppliers meet all of the requirements in this standard and all applicable supplementary standards. The purpose of this audit program is to assess a supplier's ability to consistently provide a product or service that conforms to the technical specifications and customer requirements.

An application of the new kind of the fuel for the diesel engine requires to conduct the qualification tests of the engines powered by this his fuel which allow assessing an impact of fuel on the engine reliability. Such a qualification test of the piston and turbine engines of the aircraft stationed on the ground and land vehicles is described in the NATO standardisation agreement (STANAG) 4195 as the AEP-5 test. The methodology and selected results of the qualification tests of the SW-680 turbocharged multi-purpose diesel engine fuelled with F-34 fuel have been presented in this paper. A dynamometric stand with the SW-680 engine has been described. Based on the preliminary results of the investigation it has been found that a change in a type of the fuel from IZ-40 diesel fuel into F-34 kerosene-type one has reduced a maximum engine torque by about 4%. This has been primarily due to a lower fuel density of F-34 by about 3%.

SAE International is inviting global participation in its AeroTech® aerospace and defense technology conference and exhibition, which is for the first time co-located with ASM International’s AeroMat, at the Pasadena Convention Center in Pasadena, California, March 15 through 17, 2022.

Author Francis Bradford, a former Hall-Scott engineer, provides valuable resources and insight not available to any other Hall-Scott researcher. Well-illustrated with numerous photos, drawings, and memos, this fascinating book will be of interest to history buffs in the areas of aviation, rail, marine, trucks, buses, fire equipment, and industrial engines, and to World War and military historians.

Investigating the impact of Gasoline fuel on diesel engine performance and emission is very important for military heavy- duty combat vehicles. Gasoline has great potential as alternative fuel due to rapid depletion of petroleum reserves and stringent emission legislations, under multi fuel strategy program for military heavy- duty combat vehicle. There is a known torque, horsepower and fuel economy penalty associated with the operation of a diesel engine with Gasoline fuel. On the other hand, experimental studies have suggested that Gasoline fuel has the potential for lowering exhaust emissions, especially NOx, CO, CO2, HC and particulate matter as compared to diesel fuel. Recent emission legislations also restrict the total number of nano particles emitted in addition to particulate matter, which has adverse health impact.

Tanks play a pivotal role in swiftly deploying firepower across dynamic battlefields. The core of tank mobility lies within their powertrains, driven by diesel engines or gas turbines. To better understand the benefits of each power system, this study uses geo-location data from the National Training Center to understand the power and energy requirements from a main battle tank over an 18-day rotation. This paper details the extraction, cleaning, and analysis of the geo-location data to produce a series of representative drive cycles for an NTC rotation. These drive-cycles serve as a basis for evaluating powertrain demands, chiefly focusing on fuel efficiency. Notably, findings reveal that substantial idling periods in tank operations contribute to diesel engines exhibiting notably lower fuel consumption compared to gas turbines. Nonetheless, gas turbines present several merits over diesel engines, notably an enhanced power-to-weight ratio and superior power delivery.

The aerospace industry is facing immense challenges due to increased design complexity and higher levels of integration, particularly in the electrification of aircraft. These challenges can easily impact program cost and product time to market. System electrification and electromagnetic compatibility (EMC) have become critical issues today. In the context of 3D electromagnetics, EMC electromagnetic compatibility ensures the original equipment manufacturer (OEM) that radiated emissions from various electronic devices, such as avionics or the entire aircraft for that matter, do not interfere with other electronic products onboard the aircraft.

Abstract The demand for contactless, rapid manufacturing has increased over the years, especially during the COVID-19 pandemic. Additive manufacturing (AM), a type of rapid manufacturing, is a computer-based system that precisely manufactures products. It proves to be a faster, cheaper, and more efficient production system when integrated with cloud-based manufacturing (CBM). Similarly, the need for semiconductors has grown exponentially over the last five years. Several companies could not keep up with the increasing demand for many reasons. One of the main reasons is the lack of a workforce due to the COVID-19 protocols. This article proposes a novel technique to manufacture semiconductor chips in a fast-paced manner. An algorithm is integrated with cloud, machine vision, sensors, and email access to monitor with live feedback and correct the manufacturing in case of an anomaly.