Refine Your Search

Search Results

Viewing 1 to 8 of 8
Magazine

Tech Briefs: September 2018

2018-09-01
Enhanced SATCOMs for Unmanned Aerial Systems The Bus Too Tough to Die Combating Infrared Threats on the Battlefield Optical Interconnect Design Challenges in Space High-Performance Computing for the Next-Generation Combat Vehicle Merging Antenna and Electronics Boosts Energy and Spectrum Efficiency Integrated Magneto-Optical Devices for On-Chip Photonic Systems Development of magneto-optical (MO) materials could lead to a range of nonreciprocal optical devices for emerging standardized photonic integrated circuit (PIC) fabrication processes. Low Power Optical Phase Array Using Graphene on Silicon Photonics Electrostatic doping of 2D materials embedded in waveguides could enable ultrafast devices with unprecedented power. Spatial Resolution and Contrast of a Focused Diffractive Plenoptic Camera New technology captures spectral and spatial information of a scene in one snapshot while raising pixel counts and improving image quality.
Magazine

Tech Briefs: June 2018

2018-06-01
Beyond VMEbus - A New Concept Taming the Thermal Behavior of Solid-State Military Lasers Solving the Challenge of Thermal Design in Aerospace Electronics Improving Component Life in Abrasive, Corrosive Aerospace Environments New Pulse Analysis Techniques for Radar and EW Validation of Ubiquitous 2D Radar Converting Existing Copper Wire Firing System to a Fiber-Optically Controlled Firing System for Electromagnetic Pulsed Power Experiments Technological improvements make pulsed-power experiments with gunpowder- or air-driven guns safer. Low-Cost Ground Sensor Network for Intrusion Detection COTS-based system could provide increased level of security with less manpower. In-Network Processing on Low-Cost IoT Nodes for Maritime Surveillance Commercially available system of distributed wireless sensors could increase the Navy's intelligence collection footprint.
Technical Paper

Methodology and Results of Testing an Impact of F-34 Fuel on the Engine Reliability

2020-09-15
2020-01-2133
An application of the new kind of the fuel for the diesel engine requires to conduct the qualification tests of the engines powered by this his fuel which allow assessing an impact of fuel on the engine reliability. Such a qualification test of the piston and turbine engines of the aircraft stationed on the ground and land vehicles is described in the NATO standardisation agreement (STANAG) 4195 as the AEP-5 test. The methodology and selected results of the qualification tests of the SW-680 turbocharged multi-purpose diesel engine fuelled with F-34 fuel have been presented in this paper. A dynamometric stand with the SW-680 engine has been described. Based on the preliminary results of the investigation it has been found that a change in a type of the fuel from IZ-40 diesel fuel into F-34 kerosene-type one has reduced a maximum engine torque by about 4%. This has been primarily due to a lower fuel density of F-34 by about 3%.
Video

Methodology and Results of Testing an Impact of F-34 Fuel on the Engine Reliability

2020-10-02
An application of the new kind of the fuel for the diesel engine requires to conduct the qualification tests of the engines powered by this his fuel which allow assessing an impact of fuel on the engine reliability. Such a qualification test of the piston and turbine engines of the aircraft stationed on the ground and land vehicles is described in the NATO standardisation agreement (STANAG) 4195 as the AEP-5 test. The methodology and selected results of the qualification tests of the SW-680 turbocharged multi-purpose diesel engine fuelled with F-34 fuel have been presented in this paper. A dynamometric stand with the SW-680 engine has been described. Based on the preliminary results of the investigation it has been found that a change in a type of the fuel from IZ-40 diesel fuel into F-34 kerosene-type one has reduced a maximum engine torque by about 4%. This has been primarily due to a lower fuel density of F-34 by about 3%.
Training / Education

Introduction to Airframe Engineering Design for Manufacturing, Assembly and Automation

Why is a design for manufacturing, assembly and automation so important? This introductory course on airframe engineering will cover the importance of design for manufacturing, assembly and automation in aerospace. It will review what the key drivers are for a “good” design and some of the key points for manufacturing and assembly of aircraft components. It will look at how an engineer can combine traditional technologies with new, cutting-edge technologies, to determine the best scenario for success.
Book

How to Manage the Perfect Factory or How AS6500 Can Lead To Everlasting Happiness

2020-10-01
Why AS6500? Where did it come from? Why does it exist? Those are easy questions to answer. It came from the inspiration of angels and it exists to make your life, and your factory, more perfect. That's why, when you open the standard, you can still hear the faint echoes of the singing of angels. Actually, experts were gathered from across the country, both from the Defense Department and from industry to create the new document. They toiled away until the perfect product emerged from the fruit of their labors: Aerospace Standard AS6500, "Manufacturing Management Program," published in November 2014. How to Manage the Perfect Factory combines education and instruction with fun, laughter and motivation. The book gently pokes fun at the people and organizational barriers that the Manufacturing function must overcome to make those obstacles seem more surmountable while providing key information on implementing AS6500.
Technical Paper

Comparison and Evaluation of Performance, Combustion and Particle Emissions of Diesel and Gasoline in a Military Heavy Duty 720 kW CIDI Engine Applying EGR

2020-09-15
2020-01-2057
Investigating the impact of Gasoline fuel on diesel engine performance and emission is very important for military heavy- duty combat vehicles. Gasoline has great potential as alternative fuel due to rapid depletion of petroleum reserves and stringent emission legislations, under multi fuel strategy program for military heavy- duty combat vehicle. There is a known torque, horsepower and fuel economy penalty associated with the operation of a diesel engine with Gasoline fuel. On the other hand, experimental studies have suggested that Gasoline fuel has the potential for lowering exhaust emissions, especially NOx, CO, CO2, HC and particulate matter as compared to diesel fuel. Recent emission legislations also restrict the total number of nano particles emitted in addition to particulate matter, which has adverse health impact.
Training / Education

AS13004 Process Failure Mode and Effects Analysis (PFMEA) and Control Plans

2021-05-18
In the Aerospace Industry there is a growing focus on Defect Prevention to ensure that quality goals are met. Process Failure Mode & Effects Analysis (PFMEA) and Control Plan activities described in AS13004 are recognized as being one of the most effective, on the journey to Zero Defects. This two-day course is designed to explain the core tools of Process Flow Diagrams, Process Failure Mode & Effects Analysis (PFMEA) and Control Plans as described in AS13004. It will show the links to other quality tools such as Design FMEA, Characteristics Matrix and Measurement Systems Analysis (MSA).
X