Search Results

This paper demonstrates the possibilities of using Automotive waste plastic material from “end of life” vehicles (ELVs), in the Footwear Industry to manufacture shoe components. The study establishes the sustainability of the flow of ELVs, from the European Car Parc and identifies and estimates the quantity of plastic materials potentially available for recycling from ELVs. Four potential materials, Acrylonitrile/butadiene/styrene (ABS), Polypropylene (PP), Polypropylene/ethylene/propylene/diene (PP/EPDM) and Polyamide (PA), were identified and three materials (PP, PP/EPDM and ABS) were reprocessed from ELV components and evaluated by the Footwear Industry. As a result, ABS was recommended as an economically, suitable replacement for HIPS, the current material used for manufacturing shoe heel components.

Countless articles and publications3,4,5 have documented and proven the efficacy, benefits and value of operating within a lean system. Furthermore, there exists common agreement amongst leading organizations successfully implementing a lean system that in order to do so it must take into consideration the entire enterprise, that is, from supplier to customer and everything in between6. One of the core issues this paper addresses is when the optimal time is to train and educate the people who currently have, or will have, influence over the ‘enterprise’.

TFC/IW, total fuel consumption divided by inertia weight is reported with other engineering variables for recent EPA data for industry passenger cars and truck. TFC/IW is used in comparisons between gasoline and diesel engines, 49 States and California, passenger cars and trucks. The California fuel economy penalty due to more stringent emissions standards is discussed. The relationship between TFC/IW and ton miles per gallon is shown. Special attention is focused on 4 cylinder gasoline powered vehicles in 49 States passenger car fleet. The use of TFC/IW to answer the question, ‘What Changed?’ when comparing the fuel economies of two fleets is described.

Software programs in non-application areas such as Board Support Packages, Hardware Abstraction Layers, signal processing and data acquisition are more or less very standard and common across many applications. These form a major part of the “platform” software, which changes very little. However, it is seen that many a time, efforts are spent resolving issues in the hardware dependent layers rather than concentrating on the application at hand, despite the fact that the software controlling the hardware has been developed many times. There are many reasons why this section of the software is rewritten many times over: different coding standards, different software architecture and layering concepts, the dreadful cut-and-paste methods, and so on. Introduction of a tool-based code configurator and generator eliminates access to the code and focuses on configuring a pre-written set of SW procedures. Advantages: Standardization, reuse and high levels of productivity.

This paper will discuss using Astronics “Smart Panel” illuminated control panels to control an electronic power distribution system. A discussion of wiring simplification, automatic control possibilities and real time load monitoring is presented. The challenges of retrofitting the system into older aircraft will be covered as well. The paper also explains Electronic Circuit Breaker technology, arc fault protection, panel lighting technologies, control bus options, displays, and human input technology (buttons and knobs).

IN this paper the authors present some experimental results obtained by using the analysis outlined by Prof. James J. Guest before the Institution of Automobile Engineers, in 1926. To make the experimental work more understandable, they present the essential points of Professor Guest's analysis. Professor Guest begins his analysis of the movements of a car body with the simplest set of conditions and presents a graphical as well as an algebraic solution. He then includes one additional factor after another in his analysis until the principal factors in car suspension are included. After all factors are considered, the essential structure of the simple analysis is retained. The authors' efforts at the experimental determination of the moment of inertia of passenger cars were started in January, 1932, on Sir Charles Dennistoun Burney's “tear-drop” design with which he visited leading American manufacturers.

High performance lubricant additive systems have been developed to formulate SAE 5W-30 passenger car engine oils which meet current and anticipated requirements of the North American original equipment manufacturers. The trend in North America is to recommend SAE 5W-30 oils that not only meet the API SF requirements for gasoline engines (“first-generation” oils), but also meet the stringent API CC requirement for light duty diesel engines (“second-generation” oils). Furthermore, the engine builders have issued “world specifications” for motor oils which incorporate additional “second-generation” SAE 5W-30 characteristics, such as enhanced API SF limits, improved fuel efficiency, an increased margin of bearing protection, and lower finished-oil phosphorus levels. The additive systems described herein exceed API SF and CC requirements as well as “second-generation” performance hurdles.

This paper presents, chemistry, test data and processing procedures on a non toxic and environmentally friendly chrome-free conversion coating alternative with the same level of adhesion and secondary corrosion resistance as that found in chrome containing conversion coating systems. Test data from military and independent sources will be presented on secondary coating adhesion, electrical conductivity, filiform and neutral salt-spray corrosion resistance as compared to chromate based systems .on magnesium, aluminum and zinc and their respective alloys. The European “RoSH” initiative will not allow for the presence of any hexavalent chromium on imported electrical components as of July first of 2006. Trivalent chromium based systems generate hexavalent chromium due to the oxidation of the trivalent chromium and as such will not be allowed.

A sense of “personal integrity” blocks pilot use of new information about how he thinks. Research on human performance under stress done over the past fifty years indicates increased rigidity and regression to earlier learned behavior in high stress, and in low Stress a shift in attention to any domestic situation or on the job controversy which is of higher stress than that of the job at hand, all without the pilot's knowledge. Informal surveys of commercial pilot training and commercial pilot attitudes towards these studies indicate that the study findings directly confront learned cultural responses. Pilot and trainer reactions prevent the information from being adequately investigated or formally taught. The findings are not written into training manuals and pilots who are informally given the information do not have adequate access to the knowledge when it is needed.

A survey of the in-service fuel consumption of passenger vehicles and derivatives in the Australian fleet was carried out in 1984-85. Seven hundred and four owners across Australia took part in the survey. Vehicle owners reported by questionnaire the amount of fuel used during four tank fills of normal operation, the distance travelled, and other details of the operating circumstances. The survey shows a clear downward trend in the fuel consumption of the Australian passenger fleet. The data also provides comparisons of actual fuel consumption obtained on the road, with laboratory derived values for fuel consumption. Vehicles in a sub-set of 40 were fitted with fuel flow meters during the survey and tested to Australian Standard 2077 for fuel consumption. The questionnaire method is shown to be a valid and accurate technique for determining in-service fuel consumption.

The current research was aimed at determining the most effective way to use alternative renewable feedstock to power a diesel engine. Mimusops elengi, a new and novel biofuel was recognized for this current study, which is widely available in the south of India. The investigation was conducted on B20 volume basis (20% Mimusops elengi methyl ester blended with 80% diesel). Furthermore, it was recognized that when the performance characteristics were traded off, the emission magnitude has slightly higher. To address the diesel engine pollution, an oxygenated nano additive like titanium oxide was dissipated only with the fuel blend at distinct mass fractions of 25 parts per million (ppm) with differing injection pressures of 180 bar, 200 bar, 220 bar, and 240 bar. The tests were created using a statistical programme known as design of experiments, which is purely based on Taguchi and response surface methodology.

Vehicle dynamics is a discipline of mechanical engineering that benefited of significant improvements thanks to the progress of computational engineering. Vehicle dynamics engineers are using CAE for the development of a vehicle with MBS and FEA. The concurrent use of these two technologies is a standard in the automotive industry. However the current simulation process is not fully efficient because local geometrical and material nonlinearities are not accurately modeled in classical MBS software. This paper introduces a methodology for vehicle dynamics simulation integrating MBS capabilities in one single nonlinear FEA environment enabling an accurate modeling of nonlinearity in vehicles.

MONOGAL is a coated steel developped to improve the corrosion resistance of exposed automotive body applications. Its process os based on the brittleness of the η zinc coating in a range of temperatures below the melting point of the zinc. MONOGAL is produced on a hot dip galvanizing line; at the exit of the pot the free zinc is brushed off the light side of the differentially coated sheet. Side 1 of MONOGAL presents a very thin and continuous layer of iron-zinc diffusion alloy with no free zinc. Side 2 is a standard G90 or G60 zinc coating. The iron-zinc alloy layer has excellent anti-galling properties which improve the formability of MONOGAL over two side hot dip galvanized steel with the same r value. MONOGAL also shows good weldability, paintability and corrosion resistance.

The results of several anti-knock studies are discussed in this paper. Road anti-knock performance for 1000 fuel blends covering the years 1940 to 1957 have been investigated. The laboratory Research octane numbers of these fuels covered the range from 80 to 105. The fuels were evaluated in 46 cars representing a cross-section of the automotive products for these years. The objective of these investigations was to determine the practical application of the laboratory to road octane rating relationships, and the effect of vehicles, and operating conditions on these relationships. The results show that there is a valid correlation between laboratory and road octane ratings. The relative importance of Research and Motor octane ratings on road performance is influenced by make of car, engine speed, throttle position, and distributor advance characteristics. It also indicated that aromatics improve, whereas olefins reduce high speed Modified Borderline ratings.

This paper describes the interrelated controls for automatic start sequencing, fuel scheduling, customer air delivery, and supervisory and protective systems as applied to the Curtiss-Wright CW657E “Jet-Air” Compressor. Model CW657E is capable of delivering 15,000 SCFM air at 85 psig (at 30°F and sea level pressure) and may be used in a diversity of manufacturing, processing, and industrial applications. A description of the control system and its operation in relation to compressor requirements, while furnishing air to feed distribution lines to air assisted water atomizing nozzles for snow making is reviewed as an example. Other models can deliver up to 30,000 SCFM with modified control systems, including pressure controls.

Considering that the opening of the national market varies at the mercy of the economy and the government, Mercedes-Benz do Brasil launched a program to support the local suppliers. Within this program, one may enhance the tool IQTC (Commercial and Technical Qualitative Index). One deals with an index that will enable the supplier to exactly know in which scores he is “weak”, where he is strong and where he has to improve. The transparency regarding the information has to be complete. The general composition of the index will be presented with its criteria and requisites in which the various areas of Mercedes-Benz participate in, with additional details for the IQDP (Quality Index in Product Development), that is the subindex prepared by the Development area. Some practical results involving the evaluation of suppliers will also be shown, whose results, however, will not be nominally quoted.

In the work presented to SAE in 1999: IQTC: a Practical and Unified Index to Evaluate the Continuous Improvement of Suppliers, we showed that the Development Area is one of the chapters inserted into the evaluation process of suppliers and answers for an evaluation called IQDP (Quality Index in Product Development). The present work objective is to show the difficulties found in the implementation, solutions and improvements that are being used to outline a better supplier evaluation. Such a control within a universe of 350 suppliers (directly connected to production) being evaluated by 400 persons, in a natural process, is not an easy task. Collecting information about the difficulties faced to evaluate a supplier and the supplier claims to obtain an answer in reply to the attributed scores, took us to the search of the adequate computerized technology that would allow us to group the interests of work methods that would comply with the diverse demands involved.

Over the last ten years there has been a steady growth in the market share of light-duty diesel engines, especially in Europe. At the same time, a general trend in petrol engine development has been seen, in which normal aspirated engines are being replaced by downsized turbocharged engines. Therefore, NVH engineers have to deal with new challenges. Turbochargers produce an aerodynamic noise in the frequency range above 1000Hz, which might influence the exterior and interior noise level. As a result, the additional requirement for acoustical components to reduce this flow noise is going to pose an increasing challenge for air intake system suppliers. This paper describes a new design of well-known wide band silencer first mentioned by A. Selamet, N.S.Dickey and J.M.Novak [1,2]. The silencer works according to the interference principle. The sound is guided into two or more parallel pipes of different lengths.