Search Results

Automotive industry is a major contributor to global carbon dioxide (CO2) emissions and waste generation. Not only do vehicles produce emissions during usage, but they also generate emissions during production phase and end of life disposal. There is an urgent need to address sustainability and circularity issues in this sector. This paper explores how circularity and CO2 reduction principles can be applied to design and production of automotive parts, with the aim of reducing the environmental impact of these components throughout their life cycle. Also, this paper highlights the impact of design principles on End-of-Life Management of vehicles. As Design decisions of Component impacts up to 80% of emissions [1], it is important to focus on this phase for major contribution in reduction of emissions.

In spite of environmental issues related to cadmium and its electroplating process, electroplated cadmium is still extensively used in the aerospace and defense sectors. This trend is likely to continue especially for high strength steels because cadmium provides the best known corrosion and embrittlement protection for this application. Consequently, the environmental concerns related to the cadmium electroplating have been addressed using an alternative Zero-waste Physical Vapor Deposition (Z-PVD). This method does not use liquids, it recycles cadmium in situ, and is free of hydrogen embrittlement. The Z-PVD process is now in commercial production for the aerospace fasteners. The quality of the coatings has been at least equal to that of the electroplated cadmium.

OBD system requirements were first developed by the California Air Resources Board, the U.S. Environmental Protection Agency, and the European Commission. New OBD requirements should be as consistent as possible with existing requirements to maximize reliability and to minimize system complexity, proliferation of configurations, and consumer cost. New OBD requirements from around the world are briefly reviewed and most are consistent with the original U.S. and European requirements. Worldwide OBD requirements are being further harmonized under the United Nations, Economic Commission for Europe, World Forum for Harmonization of Vehicle Regulations (WP29). Presenter David H. Ferris, General Motors Company

To investigate the feasibility of various test procedures to determine aerodynamic performance for the Phase 2 Greenhouse Gas (GHG) Regulations for Heavy-Duty Vehicles in the United States, the US Environmental Protection Agency commissioned, through Southwest Research Institute, constant-speed torque tests of several heavy-duty tractors matched to a conventional 53-foot dry-van trailer. Torque was measured at the transmission output shaft and, for most tests, also on each of the drive wheels. Air speed was measured onboard the vehicle, and wind conditions were measured using a weather station placed along the road side. Tests were performed on a rural road in Texas. Measuring wind-averaged drag from on-road tests has historically been a challenge. By collecting data in various wind conditions at multiple speeds over multiple days, a regression-based method was developed to estimate wind-averaged drag with a low precision error for multiple tractor-trailer combinations.

This paper discusses the several reasons why vehicles do not achieve the EPA MPG values in service, and makes a numerical estimate of the magnitude of the individual effects. In addition, methods for adjusting EPA MPG values to estimate road fuel economy performance are presented and discussed.

Acid rain in the U.S. is becoming a major environmental issue. This paper reviews the known information regarding pollution sources, impact on the environment and the role of the automobile in acid rain. Although natural sources of sulfur and nitrogen pollutants are equal to or greater than man-made sources on a global scale, many scientists believe man's activities are the major cause of high levels of acidity. Attempts to relate specific sources of SO2 to specific acid rain events in the northeastern U. S. have been unsuccessful. The roles of tall stacks, long range transport and dry vs. wet deposition are incompletely understood. Temporal and geographic trends in acidity are not well defined except for increased acidity in the southeast. About 30% of the acidity in rain in the northeast is due to HNO3. In the process of utilizing nitrates as a nutrient, plants partly neutralize the affect of HNO3 in the rain.

Weber Metals Inc., a division of Otto Fuchs KG of Germany, unveiled a new, $180 million, 60,000-ton press at its 2.5-acre facility in Paramount, California, southeast of Los Angeles. It sets a record as the highest tonnage hydraulic forging press in the Americas and the largest privately funded forging press investment in the world.

The paper reports on the outcome of a still on-going joint-research project with the objective of establishing a demonstrator high speed direct injection (HSDI) diesel engine in a Sport Utility Vehicle (SUV) which allows to exploit the effectiveness of new engine and aftertreatment technologies for reducing exhaust emissions to future levels of US/EPA Tier 2 and Euro 4. This objective should be accomplished in three major steps: (1) reduce NOx by advanced engine technologies (cooled EGR, flexible high pressure common rail fuel injection system, adapted combustion system), (2) reduce particulates by the Continuous Regeneration Trap (CRT), and (3) reduce NOx further by a DeNOx aftertreatment technology. The current paper presents engine and vehicle results on step (1) and (2), and gives an outlook to step (3).

After a review of current and future emission legislation for non-road engines (India, Europe, USA), the various options available to reduce the emissions of diesel tractor engines are discussed. Special emphasis is put on naturally aspirated engines in the 37 - 50 kW power range. AVL has recently designed and developed several naturally aspirated heavy-duty diesel tractor engines to comply with current exhaust emissions standards for the Indian domestic and the US markets (EPA Tier 2). In doing so, different levels of technologies were applied. Their impact on mean effective pressure, specific fuel consumption and emissions will be shown. The future non-road engine exhaust emissions legislation in different markets will be addressed (India, Europe and USA). Compliance with the new emission standards will require the introduction of more advanced technology.

The combined forces of environmental protection, consumerism, energy conservation and productivity are completely altering the nature of coatings used by the Automotive Industry. Waterborne basecoats allow application at low volume solids, thus producing optimum metallic effect while maintaining compliance with emission regulations. In order to control rheology and thereby sag resistance and metal flake orientation, a novel aqueous microgel polymer has been developed. Processing of these basecoats is similar to present solvent-borne finishes with the exception that stainless steel equipment must be used and water must be removed before application of clearcoat. The production feasibility of waterborne basecoats was first established in a Canadian truck assembly plant and in the next two years several other production facilities are expected to convert to this new technology.

Water quality standards have been completed for space vehicles and habitats for ingestion periods from 1 day to 1000 days. These standards are called spacecraft water exposure guidelines (SWEGs). The National Research Council Committee on Toxicology has worked with the Toxicology Group at the National Aeronautics and Space Administration (NASA) to set and document these standards. Prior to SWEG development, the practice of NASA was to apply the United States Environmental Protection Agency (USEPA) maximum contaminant levels (MCLs) in the interpretation of any potential health effects from water pollutants. This practice had the potential to result in erroneous conclusions because MCLs are intended for lifetime exposures and are set to protect a much more diverse population than is present in the astronaut corps. However, for certain pollutants it was recognized that the stresses of spaceflight may make astronauts more susceptible to adverse effects.

GM de Mexico Ramos Arizpe Automotive Complex (RAAC) manufactures engines and passenger cars. Located in the northern part of Mexico, the RAAC water supply comes entirely from a subsurface aquifer whose drawdown rates presently exceed its recharge rate. The original wastewater treatment facilities, installed at the beginning of the RAAC operations, became inadequate as a result of more stringent wastewater discharge limits issued by SEDUE (Mexican EPA counterpart) in 1987 (see Table I). A Water Management Study was performed in 1986-7, to determine viable solutions to the problems of insufficient water supply and wastewater treatment. A three-phase Water Management Program was adopted.

At WCX World Congress Experience you’ll participate in live panel discussions, Q&As, keynotes, and breakout sessions with researchers and leaders across the industry.