Search Results

Single-cylinder spark ignition engine experiments conducted at constant speed, fixed airflow, and using isooctane as the fuel, demonstrated the effects of fuel-air mixture preparation on lean operation. Mixture preparation was changed by varying the time of fuel injection in the induction manifold, near the intake valve port. For comparison, a prevaporized fuel-air mixture was also investigated. Emphasis was placed on determining the effects of mixture preparation on combustion characteristics. Based on the results from this study, the often favored prevaporized mixture of fuel and air may not be the best diet for lean engine operation.

This paper describes the initial works related to the study of Internal Combustion Engines, as an object of mechanical design, at the Universidad Tecnológica de Pereira. It is reported a concise, complete methodology for simple model of internal combustion engine. The emphasis of the paper is placed on the use of the in-cylinder parameters (pressure and temperature) and inertial loads in the crank-slider mechanism to derive the loads that act on all the components of the crank-slider mechanism as well as the theoretical output torque for a given geometrical structure and inertial properties. These loads can then be used to estimate the preliminary dimensions of engine components in the initial stage of engine development. To obtain the pressure and temperature inside the cylinder, under different operation parameters, such as air fuel ratio and spark angle advance, a Zero dimensional model is applied. The heat transfer from the cylinder and friction are not taken into account.

Combustion concepts for future SI engines try to meet CO2-emission commitments and legislation all over the world. Where the Diesel engine has an advantage by principle, the efficiency of the SI engine has to be improved significantly, while of course the exhaust emissions must not become worse. An approach is to reduce the gas exchange losses using fully variable valve trains on the intake side of the combustion engine. OptiVent is a patented new way of controlling the mass air flow in the cylinder of a combustion engine using opening valves during the compression phase of a four stroke engine. This technology regards a wider range of variability on the valvetrain components of the engine especially for opening the valves more than one time during a cycle. On the other hand it is necessary to combine this technology with direct injection to avoid fuel losses in the exhaust system and raising the exhaust hydrocarbon emission of the engine.

Due to the rising costs of fuel and increasingly stringent regulations, auto makers are in need of technology to enable more fuel-efficient powertrain technologies to be introduced to the marketplace. Such powertrains must not sacrifice performance, safety or driver comfort. Today's engine and powertrain manufacturers must, therefore, do more with less by achieving acceptable vehicle performance while reducing fuel consumption. One effective method to achieve this is the extreme downsizing of current direct injection spark ignited (DISI) engines through the use of high levels of boosting and cooled exhaust gas recirculation (EGR). Key challenges to highly downsized gasoline engines are retarded combustion to prevent engine knocking and the necessity to operate at air/fuel ratios that are significantly richer than the stoichiometric ratio.

Dynamic skip fire (DSF) has shown significant fuel economy improvement potential via reduction of pumping losses that generally affect throttled spark-ignition (SI) engines. In DSF operation, individual cylinders are fired on-demand near peak efficiency to satisfy driver torque demand. For vehicles with a downsized-boosted 4-cylinder engine, DSF can reduce fuel consumption by 8% in the WLTC (Class 3) drive cycle. The relatively low cost of cylinder deactivation hardware further improves the production value of DSF. Lean burn strategies in gasoline engines have also demonstrated significant fuel efficiency gains resulting from reduced pumping losses and improved thermodynamic characteristics, such as higher specific heat ratio and lower heat losses. Fuel-air mixture stratification is generally required to achieve stable combustion at low loads.

This study proposes a novel biofuel for spark ignition (SI) engine, α-pinene (C10H16), which is non-oxygenated and thus has a gravimetric energy density comparable to that of hydrocarbon fuels. The ignition characteristics of α-pinene were evaluated in an ignition quality tester (IQT) under standard temperature and pressure conditions. The measured ignition delay time (IDT) of α-pinene is 10.5 ms, which is lower than that of iso-octane, 17.9 ms. The estimated research octane number (RON) for pinene from IQT is 85. A temperature sweep in IQT showed that that α-pinene is less reactive at low temperatures, but more reactive at high temperatures when compared to isooctane. These results suggest that α-pinene has high octane sensitivity (OS) and is suitable for operation in turbocharged SI engines. With these considerations, α-pinene was operated in a single cylinder SI engine.

“Zoning” a catalytic converter involves placing higher concentrations of platinum group metals (PGM) in the inlet portion of the substrate. This is done to optimize the cost-to-performance tradeoff by increasing the reaction rate at lower temperatures while minimizing PGM usage. A potentially useful application of catalyst zoning is to improve performance using a constant PGM mass. A study was performed to assess what the optimum ratio of front to rear palladium zone length is to achieve the highest performance in vehicle emission testing. Varying the zone ratio from 1:1 to 1:9 shows a clear hydrocarbon performance optimum at a 1:5.66 (15%/85%) split. This performance optimum shows as both a minimum in FTP75 non-methane organic gas (NMOG) emissions as well as a minimum in hydrocarbon, carbon monoxide, and nitrogen oxide light-off temperature. Overall, an improvement of 18%, or 11 mg/mi of combined NMOG+NOx emissions was obtained without using additional PGM.

Long term control of the AFR (Air/Fuel Ratio) of spark ignition engines is currently accomplished with a selvoscillating PI control loop. Because of the intake/exhaust time delay, the oscillation frequency and hence bandwidth of this loop is small. This paper describes a new approach to the design of this control loop using a novel observer system. In this way the bandwidth of this important loop is increased by a factor of 2 - 6 times, leading to more accurate overall AFR control. Moreover the observer approach is so robust and allows such feedback levels that it reduces significantly the accuracy required in the calibration of the base fuel control system with which it is be used. It can be used with either conventional- or advanced observer based- base fuel strategies.

This study was undertaken to develop a better understanding of how intake charge dilution by various gases affected nitric oxide (NO) emission from a single-cylinder spark ignition engine. Carbon dioxide, nitrogen, helium, argon, steam, and exhaust gas were individually added to the intake charge of a propane-fueled, single-cylinder engine operated at constant speed and load. Nitric oxide emission was reduced in all cases. The gases with higher specific heats gave larger NO reductions. The product of diluent flow rate and specific heat correlated with NO reduction. The effects of diluents on calculated combustion temperature, mbt spark timing, and fuel consumption are also presented and discussed.

PF&L is priority event for mobility professionals that specialize in powertrain, fuels, lubricants technology, including OEM and Tier 1 component suppliers Light medium and heavy-duty vehicle system and product design engineers.

September 17-19, 2019 │ Garden Grove, CA, USA

For an open exchange about the most promising new propulsion/powertrain-related technologies for light-, medium-, and heavy-duty vehicles, the SAE 2023 Powertrains, Fuels & Lubricants Conference & Exhibition (PF&L) is where you need to be.

For an open exchange about the most promising new propulsion/powertrain-related technologies for light-, medium-, and heavy-duty vehicles, the SAE 2023 Powertrains, Fuels & Lubricants Conference & Exhibition (PF&L) is where you need to be.

Rankine powerplant advantages are found to fit best applications that call for long maintenance free life, or where the heat energy is essentially free as in bottoming and topping cycles, or in special environments as undersea or space. Worthy applications suggested on the basis of potential market size and ability to satisfy customer imposed cost and performance are: automotive and tank accessory power systems (APS), transportable refrigeration, portable power supply (GPS), standby power, remote site power, and home air conditioner drive. The automotive APS and a 1 1/2 kWe GPS are further analyzed. The APS can offer attractive features to the automobile user, including the possibility of reducing pollution from spark ignition engine. The GPS is an example showing high cost effectiveness for long operating times. It is recommended that marketing and cost studies continue, and that working fluid and heat exchanger technologies be accentuated.

The lack of clearly identified constraints for ignition and flame propagation has hindered understanding the processes which limit lean operation in spark ignition engines. This experimental study explores flame initiation and flame propagation as limits of lean operation in engines. In separate tests conducted in a single-cylinder CFR (cooperative fuel research) engine, the spark timing was either advanced or retarded from MBT* in order to determine the ignition-limit or partial-burn-limit spark timings, respectively. These two limiting spark timings were found to converge at lean mixtures. At the MBT lean misfire limit, the ignition-limit, and the partial-burn-limit spark timing lines converged. Apparently flame initiation as well as flame propagation considerations constrain lean operation. The effects of engine and ignition system-related variables on the ignition and partial-burn limits are presented and discussed.

This paper presents wear results of the top piston ring for an automotive spark ignited engine using gasoline and methanol blends. The Radiotracer Technique was employed utilising the multichannel analyser. In order to assess the wear process resulting due to each single factor viz. fuel type, engine speed, bhp and the water jacket temperature, investigations were carried out based on a series of statistically designed experiments. The design matrix employed a one half replication of 24 set. The study showed that the speed and load of an engine markedly affect the top ring wear. Use of alcohol blended fuels was found to marginally increase wear especially at low operating temperatures.

Wavelet analysis was used to calculate turbulence and mean velocity levels for LDV measurements made in a four valve spark ignition engine. Five different camshafts were tested, and they produce significantly different flow behaviour. The standard cam gives tumble and with valve deactivation, swirl is produced. One camshaft with early inlet valve closing and two camshafts with late inlet valve closing were also tested. The wavelet toolbox for Matlab version 5.1 has been used for the wavelet calculations. The wavelet technique produces both time resolved and frequency resolved velocity information. The results indicate some influence of the turbulence frequency content on the rate of heat release. Correlation against heat-release can be seen for different scales of turbulence. The breakdown of the tumble (low frequency turbulence) into high frequency turbulence can be seen clearly.

Single-cylinder engine tests, an analytical engine cycle simulation, and automobile tests were employed to study the effects of supplementing gasoline with water for use in spark ignition engines. Factors examined include: the method of water addition (both water-in-gasoline emulsions and direct manifold water addition), antiknock characteristics with water addition, MBT spark requirement, indicated engine efficiency, engine cooling requirement, exhaust emissions, volumetric efficiency, lean operating limit, smoke level, exhaust temperature, and vehicle driveability. Among the negative aspects of water addition were increased hydrocarbon emissions and decreased vehicle driveability. Also, the polyoxyethylene type of emulsifier used in the water-in-gasoline emulsions, gave poor fuel stability and caused a rapid buildup of engine deposits. However on the positive side, water-gasoline fuels have higher octane ratings and decrease nitric oxide emissions.

Under oxygen-deficient (rich) conditions, a potential route to maintaining control of carbon monoxide (CO) and hydrocarbon (HC) emissions in a three-way system is through reactions of these pollutants with water vapor (H2O). The importance of such reactions over supported rhodium was investigated in the laboratory. The water-gas shift (CO + H2O) was insignificant. Steam reforming (HC + H2O) took place, but gave CO as a product. Thus, if CO conversion governs the rich-side effectiveness of a three-way catalyst, steam reforming which converts HC to CO is unlikely, in itself, to improve three-way performance.

The most important problem arizing from methanol-gasoline is the phase separation caused by the presence of very small quantities of water. Two or three layers showing cloud points were observed after the addition of a small quantity of water, and their separation ratio could not be ascribed to their original blends ratio of methanol and gasoline. The greater the increase methanol content, the greater the increase in the amount of the lower layer and the limit of water absorption. Engine dynamometer tests were conducted on a 0.33L, 4-stroke spark ignition engine to get the effects of supplying the phase separation fuels on engine performances. The results of the separation behavior and the engine dynamometer tests are presented here and discussed.