Search Results

The vision of SESAR is to integrate and implement new technologies to improve air traffic management (ATM) performance. Enhanced automation and new separation modes characterize the future concept of operations, where the role of the human operator will remain central by integrating more managing and decision-making functions. The expected changes represent challenges for the human actors in the aircraft and on ground and must be taken into account during the development phase. Integrating the human in the ATM system development starting from the early design phase is a key factor for future acceptability. This paper describes the adaptation of currently applied Cockpit Human Factors processes in order to be able to design the aircraft for the future ATM environment.

The intent of this paper is to provide a general overview of the main engineering and test activities conducted in order to support A350XWB Ice and Rain Protection Systems certification. Several means of compliance have been used to demonstrate compliance with applicable Certification Basis (CS 25 at Amendment 8 + CS 25.795 at Amendment 9, FAR 25 up to Amendment 129) and Environmental protection requirements. The EASA Type Certificate for the A350XWB was received the 30th September 2014 after 7 years of development and verification that the design performs as required, with five A350XWB test aircraft accumulating more than 2600 flight test hours and over 600 flights. The flight tests were performed in dry air and measured natural icing conditions to demonstrate the performance of all ice and rain protection systems and to support the compliance demonstration with CS 25.1419 and CS25.21g.

Airbus is a leading aircraft manufacturer with the position as technology driver and a distinct customer orientation, broad commercial know-how and high production efficiencies. It is constantly working on further and new development of its products from ecological and economical points of view. Fuel Cell Systems (FCS) on board of an aircraft provide a good opportunity to address both aspects. Based on existing and upcoming research results it is necessary to find trend-setting measures for the industrial implementation and application of this technology. Past and current research efforts have shown good prospects for the industrial implementation and application of the fuel cell technology. Being an efficient source of primarily electric power the fuel cell would be most beneficial when used in conjunction with electrical systems.

Airbus business and Extended Enterprise require more and more involvement of design and built suppliers, tier 1 but also across the complete supply chain i.e. tier 2-n. These suppliers are not working only for Aerospace industry and may have different cultures. The pressure on cost and overall efficiency is high and everybody has to cope with obsolescence and new regulation (e.g. REACH (Registration, Evaluation and Authorization and Restriction of Chemicals)). So it became very important for Airbus to clarify the criteria under which a change can be done without Airbus review, and criteria under which a change can be done without Airworthiness authority review.

The new edition of the well known Care and Repair of Advanced Composites, 3rd Edition, improves on the usefulness of this practical guide geared towards the aerospace industry. Keith B. Armstrong, the original lead author of the first edition was still in charge of this project, counting on the expert support of Eric Chesmar, senior composites specialist at United Airlines. Mr. Chesmar is also an active member of SAE International's CACRC (Commercial Aircraft Composite Repair Committee), an elite group of industry experts dedicated to the standardization, safety, security, and efficiency of composite repairs in the airline industry. Mr. Francois Museux (Airbus) and Mr. William F. Cole II also contributed. Care and Repair of Advanced Composites, 3rd Edition, presents a fully updated approach to the training syllabus recommended for repair design engineers and composite repair mechanics.

Water is always present in jet fuel, usually in a mixture of forms. At very low temperatures this phenomenon can lead to the formation of ice crystals within the aircraft fuel system, which can then stay in suspension within the entire volume of fuel. Pumps within the fuel system transfer fuel around the system. Pumps such as boost pumps that are typically used in fuel systems are protected by a weave type filter mesh at the inlet. Ice accretion on the surface of this mesh has operational implications as it can cause non optimal fuel flow. In this investigation, two fundamental tools are being used: 1) a high fidelity MATLAB model of a mesh strainer, pick-up line and pump, and 2) a test rig of the modelled system. The model is being used to investigate fuel system performance when exposed to fuel containing water/ice contaminants at cold temperatures.

Due to the importance of fulfilling the actual and upcoming environmental legislation, it is an Airbus main target to develop eco-efficient materials. Under consideration of the economical effects, these processes will be implemented into the production line. This paper gives an overview of Airbus and its partners research work, the results obtained within the frame of the European funded, integrated technology demonstrator (ITD) ECO Design for Airframe. This ITD is part of the joint technology initiative Clean Sky. Developments with different grade of maturity from “upstream” as the investigation of materials from renewable recourses up to materials now in use in production as low volatile organic compounds cleaner are under investigation. As a basis for future eco-efficient developments an approach for a quantitative life cycle assessment will be demonstrated.

In the past decades hydraulic systems have dominated actuation tasks in aerospace applications. Even today hydraulic actuation remains in first line for primary flight controls as well as for heavy consumers such as landing gear or auxiliary applications in the perimeter of military functions. Also in future, hydraulic systems and its consumers are candidates to fulfil operational and functional requirements and provide respective improvements to ensure product competitiveness. Thus, this paper deals with potential improvements on hydraulic system level such as, fluid monitoring and light weight applications linked to impacts on aircraft level or interfacing systems.

The PLANET System was used for real-time satellite data transmission during the HAIC-HIWC Darwin field campaign (January to March 2014). The basic system was initially providing aircraft tracking, chat, weather text messages (METAR, TAF, etc.), and aeronautical information (NOTAMs) in a standalone application. In the framework of the HAIC project, many improvements were made in order to fulfill requirements of the onboard and ground science teams for the field campaign. The aim of this paper is to present the main improvements of the system that were implemented for the Darwin field campaign. New features of the system are related to the hardware component, the communication protocol, weather and tracking display, geomarkers on the map, and image processing and compression before onboard transfer.

This paper proposes a rearview on aeronautical innovation, addresses some 2000-2010 new products, and suggests elements of future vision, serving passengers aspirations. Over 100 years, aeronautics brilliantly domesticated flight: feasibility, safety, efficiency, international travel, traffic volume and noise, allowing airlines to run a business, really connecting real people. Despite some maturations, new developments should extend the notion of passenger service. So far, turbofans became silent and widebodies opened ‘air-bus’ travel for widespread business, tourism or education. Today airports symbolize cities and vitalize regional economies. 2000-2010 saw the full double-decker, the new eco-friendly freighter and electronic ticketing. In technology, new winglets and neo classical engines soon will save short-range blockfuel. In systems and maintenance, integrated modular avionics and onboard data systems give new flexibility, incl by data links to ground.

Water is a contaminant that can lead to fuel system icing, microbial contamination, corrosion and fuel quantity gauging problems and therefore an efficient water management system is required in order to maximise the performance of an aircraft's fuel system. This paper describes a time-transient aircraft fuel tank model with water contamination, due to the principal mechanisms of dissolution, suspension, condensation and transportation. The tank model presented is a component of the NEPTUNE fuel system model which was developed for Airbus using the A380 as an example aircraft. A description of the physics of water contaminated fuel is given and of how this has been incorporated into a mathematical model of an aircraft fuel tank. A modular approach is demonstrated which enables interconnecting fuel tanks to be configured in larger systems in a flexible and easily understood manner.

Fuel on-board dehydration during flight technologies has been modeled and experimentally studied on a laboratory testing setup in normal specific gas flow rates range of 0.0002-0.0010 sec-₁. Natural air evolution, ullage blowing and fuel sparging with dry inert gas have been studied. It has been shown that natural air evolution during aircraft climb provides a significant, substantial, but insufficient dehydration of fuel up to 20% relative. Ullage blowing during cruise leads to a constant, but a slow dehydration of fuel with sufficient column height concentration gradient. Dry inert gas sparging held after the end of the natural air evolution or simultaneously with natural air evolution provides rapid fuel dehydration to the maximum possible values. It potentially may eliminate water release and deposition in fuel to -50°C. It has been found that for proper dehydration, necessary and sufficient volume of dry inert gas to volume of fuel ratio is about 1.

In 1994, an ATR-72 crashed at Roselawn, Indiana, USA. It has been speculated that accident was due to Supercooled Large Droplet (SLD) icing. This accident led to a modification of the regulation rules with the definition of the Appendix O which includes freezing drizzle and freezing rain icing conditions. The associated NPRM (Notice of Proposed Rule Making) has been distributed to industry for comments on 29th June 2010 and could be applicable by beginning 2012. In order to comply with this new rule, the simulation tools, as Acceptable Means of Compliance, have to be improved and validated for these conditions. The paper presents the work performed within Airbus to review, improve and assess simulation tools capability to accurately predict physical phenomena related to SLD. It focuses in particular on splashing and bouncing phenomena which have been highlighted as the first order effects.

Safety is one of the most important aspects of which we are concerned with in the field of aerospace-systems development. There are a variety of safety assessment activities that are performed throughout a system's lifecycle. Multiple interrelated safety analysis artifacts are generated from the process. However, requirements and guidance for the synthesis and validation of the results of this analysis are insufficient and are not explicit. In traditional system development processes, certification coordination, safety assessment, requirements validation, and implementation verification are generally treated as supporting processes, which are concurrent and interactively dependent throughout the iterative development of a system. In SAE ARP4754A, these processes are stressed as integral processes with traceability between safety requirements and the dependencies between safety assessment activities highlighted as an important concern.

The High Altitude Ice Crystals (HAIC) Sub-Project 3 (SP3) focuses on the detection of cloud regions with high ice water content (IWC) from current available remote sensing observations of space-based geostationary and low-orbit missions. The SP3 activities are aimed at supporting operationally the two up-coming HAIC flight campaigns (the first one in May 2015 in Cayenne, French Guyana; the second one in January 2016 in Darwin, Australia) and ultimately provide near real-time cloud monitoring to Air Traffic Management. More in detail the SP3 activities focus on the detection of high IWC from space-borne geostationary Meteosat daytime imagery, explore the synergy of concurrent multi-spectral multiple-technique observations from the low-orbit A-Train mission to identify specific signatures in high IWC cloud regions, and finally develop a satellite-based nowcasting tool to track and monitor convective systems over the Tropical Atlantic.

Air traffic has been steadily increasing for the last years. Moreover, fuel availability at a reasonable cost seems more and more uncertain. Climate change implies that greenhouse gases emissions should be reduced. In this context, the search for new alternative fuels for aircraft seems to be a promising solution. Nevertheless, aeronautic represents a very specific transportation mode, due to its usage (short range, middle range, long range with the same fuel, worldwide distribution of the fuel…) and its compulsory security constraints. In the first part of the European project ALFA-BIRD (Alternative Fuels and Biofuels for Aircraft development - FP7), a selection of the best candidates to become the fuels for the future of aircraft has been done. The selection process was very complex, due to multiple criteria (physical properties, economical issued, environmental issues…).

Measurements in snow conditions performed in the past were rarely initiated and best suited for pure and extremely detailed quantification of microphysical properties of a series of microphysical parameters, needed for accretion modelling. Within the European ICE GENESIS project, a considerable effort of natural snow measurements has been made during winter 2020/21. Instrumental means, both in-situ and remote sensing were deployed on the ATR-42 aircraft, as well as on the ground (ground station at ‘Les Eplatures’ airport in the Swiss Jura Mountains with ATR-42 overflights). Snow clouds and precipitation in the atmospheric column were sampled with the aircraft, whereas ground based and airborne radar systems allowed extending the observations of snow properties beyond the flight level chosen for the in situ measurements.

In response to the ice crystal icing hazard identified twenty years ago, aviation industry, regulation authorities, and research centers joined forces into the HAIC-HIWC international collaboration launched in 2012. Two flight campaigns were conducted in the high ice water content areas of tropical mesoscale convective systems in order to characterize this environment conducive to ice crystal icing. Statistics on cloud microphysical properties, such as Ice Water Content (IWC) or Mass Median Diameter (MMD), derived from the dataset of in situ measurements are now being used to support icing certification rulemaking and anti-icing systems design (engine and air data probe) activities. This technical paper focuses on methodological aspects of the derivation of MMD. MMD are estimated from PSD and IWC using a multistep process in which the mass retrieval method is a critical step.

Increased production rates and cost reduction are affecting manufacturing in all mobility industry sectors. One enabling methodology that could achieve these goals in the burgeoning “Industry 4.0” environment is the optimized deterministic assembly (DA) approach. It always forms the same final structure and has a strong link to design-for-assembly and design-for-automation. The entire supply chain is considered, with drastic savings at the final assembly line level through recurring costs and lead-time reduction. Unsettled Technology Areas in Deterministic Assembly Approaches for Industry 4.0 examines the evolution of previous assembly principles that lead up to and enable the DA approach, related simulation methodologies, and undefined and unsolved links between these domains. Click here to access the full SAE EDGETM Research Report portfolio.

Improving the verification and certification process of the high lift system by introduction of virtual testing is one of the approaches to counter the challenges related to testing of future aircraft, in terms of performing more tests of more complex systems in less time. The quality of the applied modelling methods itself and the guarantee of a completely traceable simulation lifecycle management along the aircraft development are essential. The presentation shows how existing processes for the management of all test related data have to be extended to cover the specifics of using multi body simulation models for virtual tests related to high lift failure cases. Based on a demonstrator, MSC Software GmbH and Airbus developed and are still refining the SimManager based “High Lift System Virtual Test Portal”. This portal has to fulfil on the one side global requirements like data management, data traceability and workflow management.