Search Results

The combustion noise of a diesel engine can be deteriorated by combustion characteristics such as the maximum rate of heat release and the start of combustion. These combustion characteristics in turn are influenced by the factors such as the engine NVH durability, driving conditions, environmental factors and fuel properties. Therefore, we need to develop the robust combustion noise that is insensitive to these factors. To achieve this aim, methods for predicting combustion characteristics has been developed by analyzing the vibration signal measured from the engine cylinder block. The closed-loop control of injection parameters through combustion characteristics prediction has been performed to produce the desired engine combustion performance. We constructed an ECU logic for the closed-loop control and verified the design in a diesel passenger car. We also evaluated the effect of combustion noise and fuel consumption by applying the closed-loop control.

As a part of the global efforts to reduce CO2 emission, studies are in progress to derive regulation measures for CO2 emission from heavy-duty vehicles. Thus, identification of emission characteristics of CO2 for heavy-duty vehicle is required and test driving cycle for this would be necessary. Before developing a test driving cycle to identify the emission characteristics of CO2, selection of test subject vehicles and actual road test was carried out. Through this, road drive characteristics per diverse vehicle type and emission levels of CO2 were identified. Correlations between the currently used cycles of each country and the actual road were analyzed and the cycle most similar to the actual road situations was selected among various countries' cycles to verify whether its easy use was possible for the actual tests. The test driving cycle selected after comparison with actual road situations was modified so as to enable actual tests for all heavy-duty vehicles.

Emissions regulations are becoming more severe, and they remain a principal issue for vehicle manufacturers. Many engine subsystems and control technologies have been introduced to meet the demands of these regulations. For diesel engines, combustion control is one of the most effective approaches to reducing not only engine exhaust emissions but also cylinder-by-cylinder variation. However, the high cost of the pressure sensor and the complex engine head design for the extra equipment are stressful for the manufacturers. In this paper, a cylinder-pressure-based engine control logic is introduced for a multi-cylinder high speed direct injection (HSDI) diesel engine. The time for 50% of the mass fraction to burn (MFB50) and the IMEP are valuable for identifying combustion status. These two in-cylinder quantities are measured and applied to the engine control logic.

Studies of driving cycles for buses have been published in a number of papers, e.g., the Central Business District (CBD) and New York Bus (NY Bus) driving cycles. Such studies, however, cannot represent the actual driving environment of Seoul because of differences in road conditions and the volume of traffic. Thus, this study presents the development of a driving cycle for the city bus system of Seoul, the capital city of Korea. A representative route is selected by means of a statistical analysis of the city bus routes in Seoul. Experiments are performed to measure velocity, road grade, engine speed, load conditions, gear-shift patterns, and vehicle acceleration in actual Seoul traffic. A simulation model is developed to evaluate a driving cycle on the basis of the measured data obtained. The coupling effect between velocity and acceleration is analyzed, as well as the coupling effect between road grade and vehicle acceleration.

To properly respond to demands to reduce national energy consumption and meet greenhouse gas emission targets based on environment policy, the Ministry of Trade, Industry, and Energy of Korea formed a research consortium consisting of government agencies and academic and research institutions to establish the first fuel efficiency standards for medium- and heavy-duty (MHD) commercial vehicles. The standards are expected to be introduced in 2017 as Phase 1 of the plan and will regulate trucks with a gross vehicle weight in excess of 3.5 tons and buses with a carrying capacity of more than 16 persons. Most MHD commercial vehicles are custom-made and manufactured in diversified small-quantity batch production systems for commercial or public use, resulting in difficulties in utilizing mandatory vehicle tests for fuel efficiency evaluations.

Mixture preparation is a key contributor to both the combustion and emissions in automotive gasoline engines. The air-fuel ratio near the spark plug may have an effect on combustion characteristics since it is related to early flame development. Therefore, cycle resolved measurements of equivalence ratio near the spark plug is particularly important for better understanding of its contribution on combustion and emissions. This paper describes how we determined the in-cylinder equivalence ratio from the measured hydrocarbon concentration near the spark plug using a Fast Response Flame Ionization Detector (FRFID). The procedures established were then applied to a limited range of engine operating conditions, and the cycle resolved equivalence ratio near the spark plug was determined from the measured hydrocarbon concentration.

Conventional combustion models are suitable for predicting flame propagation for a wrinkled flamelet configuration. But they cannot predict the burned gas composition. This causes the overestimation of burned gas temperature and pressure. A modified method of combustion simulation was established to calculate the chemical composition and to investigate their ultimate fate in the burned gas region. In this work, the secondary products of combustion process, like CO and H2, were considered as well as the primary products like CO2 and H2O. A 3-dimensional CFD program was used to simulate the turbulent combustion and a zero dimensional equilibrium code was used to predict the chemical composition of burned gas. With this simple connection, more reasonable temperature and pressure approaching the real phenomena were predicted without additional time costs.