Search Results

In this work, an experimental and analysis methodology was developed to evaluate the preignition propensity of fuels and engine operating conditions in an SI engine. A heated glow plug was introduced into the combustion chamber to induce early propagating flames. As the temperature of the glowplug varied, both the fraction of cycles experiencing these early flames and the phasing of this combustion in the engine cycle varied. A statistical methodology for assigning a single-value to this complex behavior was developed and found to have very good repeatability. The effects of engine operating conditions and fuels were evaluated using this methodology. While this study is not directly studying the so-called stochastic preignition or low-speed preignition problem, it studies one aspect of that problem in a very controlled manner.

Stochastic or Low-Speed Preignition (SPI or LSPI) is an undesirable abnormal combustion phenomenon encountered in spark-ignition engines. It is characterized by very early heat release and high cylinder pressure and can cause knock, noise and ultimately engine damage. Much of the focus on mitigating SPI has been directed towards the engine oil formulation, leading to the emergence of the Sequence IX test and second-generation GM dexos® oil requirements. Engine design, calibration and fuels also contribute to the prevalence of SPI. As part of a recently completed research consortium, a series of engine tests were completed to determine the impact of fuel composition on SPI frequency. The fuel blends had varying levels of paraffins, olefins, aromatics and ethanol.

It is widely recognized that internal combustion engines (ICE) are needed for transport worldwide for years to come, however, demands on ICE fuel efficiency, emissions, cost, and performance are extremely challenging. Gasoline compression ignition (GCI) is one approach to achieve demanding efficiency and emissions targets. At Aramco Research Center-Detroit, an advanced, multi-cylinder GCI engine was designed and built using the latest combustion system, engine controls, and lean aftertreatment. The combustion system uses Aramco’s PPCI-diffusion process for ultra-low NOx and smoke. A P2 48V mild hybrid system was integrated on the engine for braking energy recovery and improved cold starts. For robust low-load operation, a 2-step valvetrain system was used for exhaust rebreathing. Test data showed that part-load fuel consumption was reduced 7 to 10 percent relative to a competitive 2.0L European diesel engine.

In order to further understand the sequence of events leading to stochastic preignition in a spark-ignition engine, a methodology previously developed by the authors was used to evaluate the propensity of a wide range of fuels to establishing propagating flames under conditions representative of those at which stochastic preignition (SPI) occurs. The fuel matrix included single component hydrocarbons, binary mixtures, and real fuel blends. The propensity of each fuel to establish a flame was correlated to multiple fuel properties and shown to exhibit consistent blending behaviors. No single parameter strongly predicted a fuel’s propensity to establish a flame, while multiple reactivity-based parameters exhibited moderate correlation. A two-stage model of the flame establishment process was developed to interpret and explain these results.

Onboard reforming has been proposed as a strategy for improving spark-ignited (SI) engine efficiency through knock reduction, dilution limit extension, improved thermodynamic gas properties, and thermochemical exhaust enthalpy recuperation. One approach to onboard fuel reforming is to combust fuel in the engine cylinder under rich conditions, producing a hydrogen-rich reformate gas--which can subsequently be recirculated into the engine. Hydrogen is the preferred product in this process due to its high flame speed and knock resistance, compared with other reformate constituents. In this work, the effects of engine operation, fuel composition and water injection were evaluated for their effect on reformate gas composition produced under rich combustion conditions. Engine parameters, including intake pressure, intake temperature, combustion phasing, and valve timing all had no significant impact on hydrogen yield at a given equivalence ratio.

The peak efficiency of modern spark ignited engines varies from 36% to 40% depending on the exact technology utilized. Most engines can achieve this peak efficiency for a limited operating region. Multi-speed transmissions allow the engine to operate closer to its most efficient operating regions for more significant portions of operation. In the case of hybrid powertrains, electric machines help in improving engine efficiency by adjusting operating speed and load. Engine shutdown during idle events and low loads is another avenue for improving the overall efficiency. The choice of the ideal powertrain and component sizes depends on the engine characteristics, drive cycles and vehicle technical requirements. This study examines what type of powertrains will be suitable for more efficient engines that are likely to be available in the near future. Some of the new technologies achieve higher efficiency with a trade off on power or by accepting a more restrictive operating region.

The efficiency and emission potential of pre-chamber combustion in a Miller cycle light duty gasoline engine operated under part load was evaluated. Several pre-chamber designs that examine the engine performance tradeoffs with nozzle diameter, pre-chamber volume, number of nozzles, and pre-chamber fuel enrichment were investigated for both excess air and cooled external EGR dilution strategies. The introduction of pre-chamber jet ignition was observed to significantly reduce the main-chamber combustion duration while reducing cyclic variability under dilute conditions, benefiting from the long-reach ignition jets and enhanced turbulence. However, the pre-chamber design that provided the fastest combustion led to reduced brake efficiency primarily due to increased wall heat loss. Maintaining the total nozzle area while increasing the number of nozzles was identified as a means to minimize the additional heat loss and maintain fast burn rates.