Search Results

High cycle fatigue (HCF) S-N curves of steels are applied by OEMs for direct evaluation of the products' durability or as an input to their CAE for design purpose. It has been found that the existing models for S-N data resulting HCF test might have difficulties in properly depicting the entire spectrum of fatigue lives. To overcome these difficulties, a new equation has been developed based on the relationship between the behaviors of short and long fatigue lives. The new equation was applied to model S-N data resulting from recent HCF testing of several steels and was compared with the 3 existing popular models. The comparison in the preliminary validations indicated that the new equation has high potential for application in more accurate S-N data modeling and fatigue limit prediction.

To reach safety, emissions, and cost objectives, manufacturers of automotive body structural components shape thin gauge, high strength steel tube using a series of manufacturing steps that often include bending, preforming and hydroforming. Challenging grades and bend severity require a sensitive optimization of the tubular bending process. To this end, it is necessary to achieve an understanding of efficient measurement methods capable of capturing small differences in bending formability. In preparation for an optimization of a 90o bend using Dual Phase 780 (DP780) and High Strength Low Alloy (HSLA350) thin walled tube, the measurement techniques of three formability characteristics: thinning, strain, and final geometry were statistically evaluated. In addition, the difference in the bending behaviour of the two grades was evaluated.

To reach safety, emissions, and cost objectives, manufacturers of automotive body structural and chassis components shape thin gauge, high strength steel tube with a bending, pre-forming and hydroforming process. Challenging grades and bend severity require a careful optimization of the bending procedure. A joint project between Ford and ArcelorMittal Tubular Products investigated suitable bending parameters for severe bends using commercially available thin-walled DP780 and HSLA350 tubes. This paper summarizes the measurement methods found to be capable of capturing small differences in bending formability and details the influence of bender variables such as boost, pressure die, center-line bend radius and bend angle on the wrinkling, thinning and springback of these tubes. As a result of this work, recommendations were made as to effective bender set-ups for these tubes.

Injection molding tools are expensive and the fatigue failure during production would result in very costly rework on the tool and downtime. Currently, mold designs are mostly based on expert experience without a careful stress analysis and the mold tool life cycle relies largely on rough estimates. The industry state of the art applies averaged temperature change and peak pressure load on the mold tool. The static analysis is then performed. Mold temperature history and thermal shock are not considered in the durability analysis. In this paper, a transient thermal analysis of the tool is performed in conjunction with the injection molding process simulation. The spatial and temporal variation of temperature, pressure and clamping forces are exported from Moldflow simulation. These histories of temperature and pressure are converted to appropriate loading curves and mapped into Abaqus FEA model.

Predicting fracture behavior of Advanced High Strength Steels (AHSS) on both manufacturing and crash simulations is becoming more and more important with the wide use of AHSS in automotive industry. The accurate measurement of fracture strains is a critical input for predicting failure in FEA simulations. It is well known that fracture is a highly localized behavior and fracture strain is gauge or size dependent. In this paper, a full field measurement technique, Digital Image Correlation (DIC), is employed to measure gauge-dependent fracture strains for several Advanced High Strength Steels (AHSS) under tensile test conditions and Limit Dome Height (LDH) tests. Applications of the fracture strains for FEA simulation are discussed.

With tighter environmental regulations, as well as political and public opinion pressure, the reduction of automotive polluting gas emissions is subject to intense debates and interests. Before a potential transition to full electrical vehicles as the long term solution, the reduction of mass remains of prime importance to permit direct reduction of emissions in internal combustion engine (ICE) vehicles. In addition to the challenges of structural integrity and safety issues, the acoustical and vibration performance of vehicles can be greatly influenced by mass reduction. This article presents a case study of lightweight design of an automotive door with a high strength steel thin gauge outer panel. An experimental comparison between a reference and a lightweight door was conducted in a complete vehicle, allowing assessing the potential effect of the mass reduction on the acoustic and vibrational performances.

Third generation advanced high strength steels (AHSS) that rely on the transformation of austenite to martensite have gained growing interest for implementation into vehicle architectures. Previous studies have identified a dependency of the rate of austenite decomposition on the amount of strain and the associated strain path imposed on the sheet. The rate and amount of austenite transformation can impact the work hardening behavior and tensile properties. However, a deeper understanding of the impact on toughness, and thus crash performance, is not fully developed. In this study, the strain path and strain amounts were systematically controlled to understand the associated correlation to impact toughness in the end application condition (strained and baked). Impact toughness was evaluated using an instrumented Charpy machine with a single sheet v-notch sample configuration.

This study introduces a new practical calibration approach of ductile fracture models by performing square punch tests on metal sheets. During square punch tests, ductile fracture occurs at either the corner of die or punch radius when applying different clamping loads and lubrication conditions. At the corner of die radius, in-plane pure shear is induced at the intersection between the side-walls and the flange by combined tension and compression. On the other hand, the material at the corner of the punch radius is under combined bending and biaxial tension. The material studied in this paper is advanced high strength steel (AHSS) DP780 from ArcelorMittal. Isotropic J2 plasticity model with mixed Swift-Voce hardening rule is calibrated from uniaxial tensile tests.