Search Results

Nowadays, optimization of manufacturing and assembly operations requires taking into account the inherent processes variations. Geometric and dimensional metrology of mechanical parts is very crucial for the aerospace industry and contributes greatly to its. In a free-state condition, non-rigid parts (or compliant parts) may have a significant different shape than their nominal geometry (CAD model) due to gravity loads and residual stress. Typically, the quality control of such parts requires a special approach where expensive and specialized fixtures are needed to constrain dedicated and follow the component during the inspection. Inspecting these parts without jig will have significant economic impacts for aerospace industries, reducing delays and the cost of product quality inspection. The Iterative Displacement Inspection (IDI) algorithm has been developed to deal with this problem.

From purchase order to production womb-to-tomb in 5 months to the day, Bombardier's Fuselage Assembly line was upgraded and made into a fuselage automated assembly pulse line. This was accomplished with a factory move of the assembly line while maintaining production of this legacy line without missing one aircraft. Early in 2012, a bold decision was made to change the plan from a manual process to an automated process and implemented on schedule. This was applying automation to a legacy aircraft assembly line. It worked. Both technology and recurring cost savings will be addressed in this paper.

Statistical process control (SPC) has been extensively used in many different industries including automotive, electronics, and aerospace, among others. SPC tools such as control charts, process capability analysis, sampling inspection, etc., have definitive and powerful impact on quality control and improvement for mass production and similar production systems. In aerospace manufacturing, however, applications of SPC tools are more challenging, especially when these tools are implemented in processes producing products of large sizes with slower production rates. For instance, following a widely accepted rule-of-thumb, about 100 units of products are required in the first phase of implementing a Shewhart type control chart. Once established, it then can be used for process control in the second phase for actual production process monitoring and control.

The safe operation of technical systems is a mandatory basic requirement for the entire industry. However, there are specific industries where the safety of operation is critical and is considered as a required characteristic. These types of industries include the aerospace, military, civil aviation, nuclear power, as well as chemical and automotive industries. Safety is everyone's responsibility but engineering plays the most important role in the course of achieving a safe product operation. There are two specific phases of the product life cycle where the safety characteristics should be addressed by engineering activities: the design and development and operation phases. Modern engineering education is oriented to provide future engineers with a sufficient background to be able to Conceive-Design-Implement-Operate.

The aircraft components' lifetime is a key decision–making metric for the performance of safety–critical items. The piece–part degradation and age–related changes are critical from the perspective of design and continued airworthiness. The most obvious issue during design development is to establish the need for planned replacement for components that are known to have a limited life. During investigation of an airworthiness issue, it is necessary to determine if the anomaly is time–dependent. If it is, then the anticipated failure probability as a function of time must be estimated such that a decision regarding corrective action can be made. For both cases, an analysis must be performed to determine if and when planned replacement is necessary. Because unanticipated retrofits are costly and difficult, credible and accurate lifetime prediction is essential.

The need for efficient manufacturing approaches has emerged with the increasing usage of composites for structural components in commercial aviation. Resin Transfer Molding (RTM), a process where a fiber preform is injected with resin into a closed tool, can achieve high fiber content required for structural components as well as improved dimensional accuracy since all surfaces are controlled by a tool surface. Moreover, RTM is well suited for parts that can be standardized throughout the aircraft, such as a fuselage frames and stringers. The objective of this investigation is to develop a preforming approach for a C-Shaped Fuselage frame. Two approaches are proposed: tri-axial braiding and hand lay-up of Non-Crimp Fabrics. The fiber architecture of the basic materials as well as the complete preforms is explained. The necessary preforming operations are detailed. The quality control measurement of fiber orientation and thickness are presented.

Bombardier faced new manufacturing process challenges drilling and fastening CSeries* aircraft panels with multi-material stacks of composite (CFRP), titanium and aluminum in which Gemcor responded with a unique, flexible CNC Drivmatic® automatic fastening system, now in production at Bombardier. This joint technical paper is presented by Bombardier, expounding on manufacturing process challenges with the C Series aircraft design requirements and Gemcor presenting a unique solution to automatically fasten CFRP aft fuselage panels and aluminum lithium (Al Li) cockpit panels with the same CNC Drivmatic® system. After installation and preliminary acceptance at Bombardier, the CNC system was further enhanced to automatically fasten the carbon fiber pressure bulkhead dome assembly.

Manufacturing operations introduce unreliability into hardware that is not ordinarily accounted for by reliability design engineering efforts. Inspections and test procedures normally interwoven into fabrication processes are imperfect, and allow defects to escape which later result in field failures. Therefore, if the reliability that is designed and developed into an equipment/system is to be achieved, efforts must be applied during production to insure that reliability is built into the hardware. There are various ways to improve the reliability of a product. These include: Simplification Stress reduction/strength enhancement Design Improvement Using higher quality components Environmental Stress Screening before shipment Process Improvements, etc. This paper concentrates on ‘Manufacturing Process Improvement’ effort through the use of design of experiments, (DOE). Hence, improved levels of reliability can be achieved.

The hydraulic actuators are used to power flight control surfaces of the aircraft and to ensure surface movement. A system of two or three actuators is usually designed depending on the surface and intuitively these actuators are considered as a redundant architecture from a reliability and functionality point of view. The proper reliability modeling of the system of actuators must consider the system's functionality and design constraints for the remaining available actuator hinge-moment in the event of a partial or total actuator failure. As a result, this will affect the reliability assessment of that design. Furthermore, this system of actuators is also designed to provide a second function involving an assurance of the surface stiffness and damping. Generally, this second function does not require necessarily the same number of available actuators in order to be fully provided.

Metal matrix composites (MMCs) exhibit superior characteristics such as low weight, high stiffness, and high mechanical and physical properties. Inheriting such an outstanding combination of specifications, they are nowadays considered as the promising materials in the aerospace and biomedical industries. However, the presence of high abrasive reinforcing particles in MMCs leads to severe manufacturing issues. Due to the tool-particle interactions which occur during the machining of MMCs, high tool wear and poor surface finish are induced and those elements are considered as the main drawbacks of cutting MMCs. In this study, dry turning experiments were conducted for two different inserts and coated carbide on a bar of titanium metal matrix composite (Ti-MMC). Semi-finishing machining is operated with cutting parameters based on the tool supplier's recommendations which were not fully optimized. The maximum flank wear length (VBBmax) was selected as the tool wear criteria.