Search Results

The aim of the study was to investigate the difference between car-to-e-bikes and car-to-pedestrian accidents. The China In-depth Accident Study (CIDAS) database was searched from 2011 to 2013 for pedestrians and e-bikes struck by car, van and SUV fronts, which resulted in 104 pedestrian and 85 e-bike cases where information was sufficient for in-depth analysis. Reconstruction by PC-Crash was performed for all of the sampled cases. Pre-crash parameters were calculated by a MATLAB code. Focus was on prototypical accident scenarios and causes; speed as well as possible prevention countermeasures. It has been shown that traffic light violations, road priority violations, and unsure safety (these situations included misjudgments, unpreparedness, proximity to other road users, inappropriate speeds, etc.…) are the main causes in both the VRU groups. Distinctions were found for aspects of car collision speed, accident scenario, distribution of head contact points and so on.

In this study, a new system of assessment method was developed to evaluate the characteristics of urban buses based on remote online monitoring. Four types of buses, including China V emission standards diesel bus, lean-burn CNG bus, air-fuel equivalence ratio combustion CNG bus and gas-electric hybrid bus, were chosen as samples to analyze the emission characteristics of urban buses with different engine types in urban scenario. Based on the traffic conditions in Beijing, the actual emission characteristics of buses under newly-built driving conditions were analyzed. Moreover, the emission factor database of urban buses in Beijing was established to analyze the characteristics of excess emission. The research results are shown as follows. 1) Compared with other types of buses, NOX emission factor and emission rate of lean-burn CNG bus are much higher.

To restrain the environmental and energy problems caused by oil consumption and improve fuel economy of heavy-duty commercial vehicles, China started developing relevant standards from 2008. This paper introduces the background and development of China's national standard “Fuel consumption test methods for heavy-duty commercial vehicles”, and mainly describes the test method schemes, driving cycle and weighting factors for calculating average fuel consumption of various vehicle categories. The standard applies to heavy-duty vehicles with the maximum design gross mass greater than 3500 kg, including semi-trailer tractors, common trucks, dump trucks, city buses and common buses. The standard adopts the C-WTVC driving cycle which is adjusted on the basis of the World Transient Vehicle Cycle[1, 2] and specifies weighting factors of urban, rural and motorway segments for different vehicle categories.

Because of the advantages of excellent power, fuel economy and zero-emission characteristics, electric buses have been used widely as cities’ short-range commuter vehicles. However, the high-frequency noise becomes more prominent for the powertrain system of the electric bus due to the lack of noise masking effect for the traditional internal combustion engine. To improve the noise characteristic of electric bus powertrain, the identification of the main noise source of the powertrain is well needed. In this paper, the effects of the motor and transmission on the noise level of the electric bus powertrain have been studied using lead packaging method. The variations of acoustical power level of the powertrain according to different rotation speed and torque under the conditions of only motor covered and only transmission covered have been discussed.

The underbody diffusers are used widely in race cars to improve the flow field structure at the bottom of the car and provide enough downforce. In recent years, passenger cars have begun to use bottom diffuser to improve aerodynamic characteristics, so as to reduce drag and increase downforce. In this paper, the aerodynamic characteristics of the bus with different underbody diffuser angles and channel numbers are studied by numerical simulation analysis. Firstly, the aerodynamics of the bus under different diffuser inlet and outlet angles are studied, and then an optimal inlet and outlet angle is determined based on the simulation results. Then, using this angle as a constant, the 2, 3, and 4 channel numbers were chosen as the diffuser channel variables to study the influence of the multiple-channel diffusers on the aerodynamic drag of the vehicle.

With the development of vehicle technologies, vehicle safety is much better than before, many companies put research focus on harder accident scenarios. The 25% overlapping collision is considered as one type of most dangerous collision, this paper study this type accidents base on CIDAS database. Paper showed 7 scenarios appeared frequency in China, 11, 12, 1 o’clock are main impact direction. High way and freeway are the main places, and the head, thorax and lower extremities were the main sites of injury.

The fatigue load spectrum of the physical proving ground is the necessary input for fatigue life analysis of vehicle parts and components. It is usually obtained by Road Load Data Acquisition (RLDA) and loads decomposition using multi-body dynamics tools. Virtual Proving Ground (VPG) methodology is gradually replacing this technical strategy. The belgian road is the typical event in durability test, in this paper, the flexible body and FTire model are applied to the vehicle multi-body dynamics model in order to improve the simulation accuracy. The result shows that all the wheel center force, shock absorber displacement and axial force acquired by VPG simulation have excellent correlation with real vehicle measured data. It is also proved that the virtual proving ground technology is a reliable and effective method to obtain the fatigue load spectrum in the early stage of development.