Search Results

This paper describes Programmed Ride Control (PRC), the automatic adjustable shock absorber system designed and patented by Ford Motor Company. The system utilizes low shock absorber damping under normal driving conditions to provide soft boulevard ride, automatically switching to firm damping when required for improved handling. The system's microprocessor control module “learns” where the straight ahead steering wheel position is, allowing the system to respond to absolute steering wheel angle. A closed loop control strategy is used to improve system reliability and to notify the driver in the event of a system malfunction. Fast acting rotary solenoids control the damping rate of the shock absorbers.

Frequency domain testing has had limited use in the past for durability evaluations of automotive components. Recent advances and new perspectives now make it a viable option. Using frequency domain testing for components, test times can be greatly reduced, resulting in considerable savings of time, money, and resources. Quality can be built into the component, thus making real-time subsystem and full vehicle testing and development more meaningful. Time domain testing historically started with block cycle histogram tests. Improved capabilities of computers, controllers, math procedures, and algorithms have led to real time simulation in the laboratory. Real time simulation is a time domain technique for duplicating real world environments using computer controlled multi-axial load inputs. It contains all phase information as in the recorded proving ground data. However, normal equipment limitations prevent the operation at higher frequencies.

Automakers have the opportunity to utilize bio-based composite materials to lightweight cars while replacing conventional, nonrenewable resource materials. In this study, Life Cycle Assessment (LCA) is used to understand the potential benefits and tradeoffs associated with the implementation of bio-based composite materials in automotive component production. This cradle-to-grave approach quantifies the fiber and resin production as well as material processing, use, and end of life for both a conventional glass-reinforced polypropylene component as well as a cellulose-reinforced polypropylene component. The comparison is calculated for an exterior component on a high performance vehicle. The life cycle primary energy consumption and global warming potential (GWP) are evaluated. Reduced GWP associated with the alternative component are due to the use of biomass as process energy and carbon sequestration, in addition to the alternative material component's lightweighting effect.

This paper describes the fabrication and operation of a low-cost, monolithic silicon mass-air-flow sensor (MAFS) developed for automotive applications. The device is a hot wire anemometer made of two thin single-crystal silicon beams, one being the heated element and the other serving as a temperature reference. Temperature compensation techniques and the design tradeoffs to maximize performance while ensuring durability in the harsh automotive environment are discussed.

This paper discusses the testing for retentivity of non-volatile memories. The physics associated with the reliable production of various non-volatile data storage devices has long been a topic of debate. The ability to reliably produce devices which endure erase/write cycling and retain data for extended periods of time has been questionable. Recent improvements in IC processing has given rise to claims of enhancements in both of these areas. Non-volatile memories are attractive in many automotive electronic applications where battery backup is neither convenient or feasible, but because of reliability concerns they have not found their way into critical applications. In applications like odometer or emission control calibrations it is imperative that memory retention is assured. In order to verify the reliability of the various available non-volatile memory devices, an accelerated test program was instituted.

An analytical method for the determination of hydrocarbon and ether emissions from gasoline-, methanol-, and flexible-fueled vehicles is described. This method was used in Phase I of the Auto/Oil Air Quality Improvement Research Program to provide emissions data for various vehicles using individual reformulated gasolines and alternate fuels. These data would then be used for air modeling studies. Emission samples for tailpipe, evaporative, and running loss were collected in Tedlar bags. Gas chromatographic analysis of the emissions samples included 140 components (hydrocarbons, ethers, alcohols and aldehydes) between C1 and C12 in a single analysis of 54-minutes duration. Standardization, quality control procedures, and inter-laboratory comparisons developed and completed as part of this program are also described.

Analytical methods for determining individual aldehyde, ketone, and alcohol emissions from gasoline-, methanol-, and variable-fueled vehicles are described. These methods were used in the Auto/Oil Air Quality Improvement Research Program to provide emission data for comparison of individual reformulated fuels, individual vehicles, and for air modeling studies. The emission samples are collected in impingers which contain either 2,4-dinitrophenylhydrazine solution for the aldehydes and ketones or deionized water for the alcohols. Subsequent analyses by liquid chromatography for the aldehydes and ketones and gas chromatography for the alcohols utilize autoinjectors and computerized data systems which permit high sample throughput with minimal operator intervention. The quality control procedures developed and interlaboratory comparisons conducted as part of this program are also described.

A number of advancements have been made in the coulometric sulfur trace instrumental technique for the real-time measurement of engine oil economy. These advancements include modification of the coulometric cell to improve reliability and reproducibility. The instrument has been interfaced with a microcomputer for instrument control as well as data acquisition, storage, and analysis. Studies were undertaken which demonstrate sufficient sensitivity and linearity for determination of engine oil economy at levels better than 10,000 miles/quart. Applications to steady-state engine oil consumption mapping and to instantaneous oil consumption during transient engine cycling are described. These instruments are being produced by an outside supplier for use in various company locations in both the engine production and engine research environments.

To serve the need of in-line rear axle diagnostics as well as other types of transmission inspection, an angular sensor development has been undertaken. It has resulted in a new device, incorporated into a system which performs angular error sensing at three levels. High precision of better than 0.003% in velocity variations is achieved. A continuous check of the null-error status of the devices is maintained in order to ensure maximum reliability of the readings. An easy on-site calibration check is available which eliminates the need for any precision calibrating fixture. The device is configured to accommodate a pass-through drive shaft for in-line mounting. A rugged design and immunity to rotor imperfections are advantageous in a plant environment.

The paper describes the application of surface mounted technology to cost reduce and downsize an existing electronic control module. Ford Motor Company's Lamp Outage Module was chosen to demonstrate the advantages of this technology. The application of this new manufacturing technology to an automotive product required careful printed circuit board design and component selection. The design considerations, test plan and reliability results are presented. The test results indicate that with proper component selection performance can be obtained that surpasses the existing manufacturing process. This technology does promise vehicle cost reductions as it is applied to other automotive products.

Sliding door designs are applied to rear side doors on vans and other large vehicles with a trend towards dual sliding doors with power operation. It is beneficial for the vehicle user to reduce the weight of and space occupied by these doors. Alcoa, in conjunction with Ford, has developed a multi-product, multi-material-based solution, which significantly reduces the cost of an aluminum sliding door and provides both consumer delight and stamping-assembly plant benefits. The design was successfully demonstrated through a concept readiness/technology demonstration program.

Future European air quality standards for light duty diesel vehicles will include stringent NOx emission regulations. In order to meet these regulations, a lean NOx catalyst system may be necessary. Since the catalytic removal of NOx is very difficult with the large concentration of oxygen present in diesel exhaust, a reductant is usually added to the exhaust to increase the NOx conversion. This paper describes a lean NOx catalyst system for a Transit light-duty truck which uses a reductant solution of urea in water. In this work, a microprocessor was used to vary the amount of the reductant injected depending on the operating conditions of a 2,5 L naturally aspirated HSDI engine. The NOx conversions were 60% and 80% on the current European driving cycle and the U.S. FTP cycles, respectively. Data on the emissions of HC, CO, NOx, particulate mass and composition, individual HC species, aldehydes, PAH and most HC species were evaluated.

Four regenerator matrix samples, fabricated by different manufacturing methods and consisting of different ceramic materials and cell geometries, were studied to determine their reliability and performance potential in a typical industrial gas turbine engine. Hypothetical regenerators were designed from these matrix samples to give identical engine performance, and the thermal stress was determined for each. In some instances, it was necessary to stress relieve and preload the rims in order to reduce the thermal stresses so that acceptable reliability could be obtained. The four hypothetical regenerators were then compared on the basis of size, cost, leakage, etc., so that the advantages of each configuration could be observed. The performance and reliability analysis was based on Ford Motor Company's shuttle rig performance tests and over 200,000 core-hours of engine test on ceramic regenerators. The engine test program is described in detail.

The purpose of this paper is to describe the growth and the trends of automotive convenience products. These products contributed to make the driving experience more pleasurable. Electronics have contributed to this growth since the sixties, and its contribution and prospects will be the prime focus of this paper. With the continuing advance of electronic products in the consumer and industrial sectors, the consumer wants' and expectations are changing, especially with the “Baby Boom” generation. More new convenience features will be developed by the prudent use of electronics. The development of these future products require a thorough understanding of consumer wants and needs through market research, careful adaptation of the emerging technology to avoid gimmickry, and dedicated application of engineering know how to design package efficient, cost effective and reliable products.

Obstacle detection technology has made significant progress in the last five years in the important product areas of quality, performance and affordability. Ford Motor Company's market research indicates that our customers are very interested in new safety features. Drivers consider obstacle detection and collision warning technology as the next breakthrough in safety technology. Ford recognizes the importance of moving from the collision mitigation to the collision avoidance paradigm. Fortunately, the first step in collision avoidance can be taken by equipping the vehicle with reliable and affordable obstacle detection sensors

In design for durability, it is generally believed that a compressive mean stress is beneficial and a tensile mean stress is detrimental. Quantitatively the effect of mean stress on fatigue life however is still inconclusive and may very well depend on both the material used and the loading conditions. Over the years, many models have been proposed to help predict mean stress effects. For example, in the long life region, Goodman's formula is widely used, while the Smith-Watson-Topper damage parameter seems the most popular for use in computerized local strain based fatigue tools. In this paper, several frequently cited mean stress correction methods together with the most recent crack closure based method are compared in various ways. Particular emphasis is given to the effect of yield level mean stresses, which has been traditionally neglected but is of practical importance to the ground vehicle industry.

The Composite Lightweight Automotive Suspension System is a composite rear suspension knuckle/tieblade consisting of UD prepreg (epoxy resin), SMC (vinylester resin) carbon fibre and a steel insert to reduce the weight of the component by 35% and reduce Co2. The compression moulding manufacturing process and CAE optimisation are unique and ground-breaking for this product and are designed to allow high volume manufacture of approx. 30,000 vehicles per year. The manufacturing techniques employed allow for multi-material construction within a five minute cycle time to make the process viable for volume manufacture. The complexities of the design lie in the areas of manufacturing, CAE prediction and highly specialised design methods. It is a well-known fact that the performance of a composite part is primarily determined by the way it is manufactured.

A compact in-situ tensile stress fixture was designed for the study of the combined effects of stress and automotive environments on structural glass fiber-reinforced composite materials. With this fixture, a standardized 300 hour laboratory screening test was developed to compare the residual property loss of composite materials due to concurrent exposure to stress and environment. It is of great importance that the data gathered in the laboratory have correlation to on-vehicle (in-service) performance, and that both lab and real world data be taken with a test system (in-situ test fixtures) capable of providing accurate and consistent results under either test condition.

Road to rig problems exist as long as vehicles are being tested. Many approaches and methods exist to produce test cycles for rigs or test tracks, in order to produce viable results for the generation of statements concerning such crucial aspects as durability and fuel consumption. Modern model strategies again demand shorter–than–ever development periods, whilst meeting better–than–ever the needs and demands of special target groups. Therefore, the testing methods must also be refined, in order to gain a closer correlation to the customer's vehicle deployment. The approach introduced here makes use of real–world customer data for obtaining a closer look at how the vehicle is used by different customer groups, in different countries. The data is collected by small and unobtrusive dataloggers installed in customer vehicles. As these customers are using their own vehicles in everyday life, being unaware of the acquisition process, a database of real customer usage is generated.

Incremental Sheet Forming (ISF) is an emerging sheet metal prototyping technology where a part is formed as one or more stylus tools are moving in a pre-determined path and deforming the sheet metal locally while the sheet blank is clamped along its periphery. A deformation analysis of incremental forming process is presented in this paper. The analysis includes the development of an analytical model for strain distributions based on part geometry and tool paths; and numerical simulations of the forming process with LS-DYNA. A skew cone is constructed and used as an example for the study. Analytical and numerical results are compared, and excellent correlations are found. It is demonstrated that the analytical model developed in this paper is reliable and efficient in the prediction of strain distributions for incremental forming process.