Search Results

The cyclic behavior of single overlap aluminum joints joined through a number of different methods has been investigated using Alcan 5754-O, an alloy that potentially could be used in structural applications. Overlap shear tests of spot welded, clinched and riveted joints are compared on the basis of their fatigue performance. The fatigue response of the spot welded joint was the baseline to which the other fasteners were compared. Test results showed an improvement of approximately 25% for both the mechanical clinch joints and aluminum rivets in fatigue strength at 106 cycles. The most significant improvement in fatigue strength of 100% was found for the self piercing rivets at 106 cycles. The failure behavior of the various joining methods is discussed as well as the surface appearance.

A 1990 Ford Taurus operated on reformulated gasoline was tested under three modes of malfunction: disabled heated exhaust gas oxygen (HEGO) sensor, inactive catalytic converter, and controlled misfire. The vehicle was run for four U.S. EPA UDDS driving schedule (FTP-75) tests at each of the malfunction conditions, as well as under normal operating conditions. An extensive set of emissions data were collected. In addition to the regulated emissions (HC, CO, and NOx), a detailed chemical analysis was carried out to determine the gas- and particle-phase non-regulated emissions. The effect of vehicle malfunction on gas phase emissions was significantly greater than it was on particle phase emissions. For example, CO emissions ranged from 2.57 g/mi (normal operation) to 34.77 g/mi (disable HEGO). Total HCs varied from 0.22 g/mi (normal operation) to 2.21 g/mi (blank catalyst). Emissions of air toxics (1,3-butadiene, benzene, acetaldehyde, and formaldehyde) were also significantly effected.

A model is presented which incorporates the key mechanisms in the formation and reduction of unburned HC emissions from spark ignited engines. The model includes the effects of piston crevice volume, oil layer absorption / desorption, partial burns, and in-cylinder and exhaust port oxidation. The mechanism for the filling and emptying of the piston crevice takes into account the location of the flame front so that the flow of both burned gas and unburned gas is recognized. Oxidation of unburned fuel is calculated with a global, Arrhenius-type equation. A newly developed submodel is included which calculates the amount of unburned fuel to be added to the cylinder as a result of partial burns. At each crankangle, the submodel compares the rate of change of the burned gas volume to the rate of change of the cylinder volume.

A four-stroke, spark-ignition engine is described that seeks to achieve high expansion ratio and low throttling losses at light load, whilst retaining good knock resistance at full load operation and without the need for expensive mechanical changes to the engine. The engine does, however, incorporate a second inlet (transfer) valve and associated transfer port linked to the intake port. The timing of the transfer valve is different from that of the main inlet valve. Load modulation is achieved by control of the gas outflow from the transfer port. A computer model of the engine is first validated against measured data from a conventional engine. Comparisons are made of incylinder pressure at part load conditions, total air flowrate through the engine and intake port air velocities as a function of crank angle position.

The galvanostatic polarization method was used to determine the pitting potentials of candidate wrought aluminum alloys in inhibited ethylene glycol engine coolants. It was shown that the relative value of the pitting potential is an excellent measure of the long-term effectiveness of the coolants in preventing spontaneous pitting and crevice attack in the aluminum heat exchangers. The long-term effectiveness was determined by metallographic examination of aluminum heat exchangers subjected to a four-month, 50,000 mile simulated service circulation test.

In this study an attempt to understand and demonstrate the effects of various washcoat technologies under active and passive regeneration conditions was performed. Six different formulations, on 1.0" D. x 3.0" L. SiC wall flow filters at the laboratory level were used at various test conditions, including variable NO₂/NO ratios and O₂ concentrations. Samples were regenerated using active and passive conditions to evaluate regeneration rates and the potential impact of regeneration at the vehicle level. Results were applied to vehicle operating conditions to determine passive functionality and potential benefits. Active regenerations at 2% O₂ and 5% O₂ showed no significant difference in time to complete regeneration and soot burn rates. Active regenerations performed at 1% O₂ and 5% O₂ concentration showed that the regeneration temperature was shifted by approximately 50°C.

A study was carried out to increase our understanding of the emissions of air toxics from normal and high-emitting vehicles. This study is part of a larger study on fuel effects in high-emitting vehicles, and is part of the Auto/Oil Air Quality Improvement Research Program (AQIRP). Detailed measurements were carried out on the emissions of two vehicles run on industry-average gasoline. The two vehicles, having similar emissions control technologies, represent a high-emitting vehicle and a normal-emitting vehicle. In addition to the regulated emissions (HC, CO, and NOx), a detailed chemical analysis was carried out on the gas - and particle-phase non-regulated emissions. The vehicles were tested over the U.S. EPA UDDS driving schedule. The high emitter was highly variable with regard to emissions, but always operated rich of the stoichiometric point. Up to 46% of fuel carbon was emitted as CO and unburned HC for the high emitter, compared to less than 1.4% for the normal emitter.

Vehicle body with aluminum riveted construction instead of steel welded one will be a big challenge to NVH. In this paper, aluminum and steel rails with the dimensions similar to the rear rail portion of a typical mid-size sedan were fabricated. Rivets were used to assemble the aluminum rails while welds were used to assemble the steel rails. Adhesive, rivet/weld spacing, and rivet/weld location were the three major factors to be studied and their impact on NVH were investigated. The DOE matrix was developed using these three major factors. Modal tests were performed on those rails according to the DOE matrix. The FEA models corresponding to the hardware were built. CAE modal analysis were performed and compared with test data. The current in-house CAE modeling techniques for spot weld and adhesive were evaluated and validated with test data.

Here we present an analytical model, written in general terms, which predicts the trajectory of a spherical particle/droplet placed in a uniform fluid stream. The model is compared to an experiment in which three millimeter diameter polypropolyene spheres (specific gravity = 0.91) are dropped in a uniform airstream (velocity varies from 0.9 to 3.8 m/s). Agreement between the two suggests the model incorporates all the important physics and thus should be useful as a design tool.

In this paper, we present the results of a series of experiments to determine the exhaust particulate size distributions from a number of diesel, gasoline and compressed natural gas (CNG) fuelled vehicles. The results show that all three types of vehicle produce significant populations of particulates under certain operating conditions. Particulates produced by gasoline and CNG engines tend to be smaller than for diesel engines. At low loads, there is a significant particulate distribution for diesel engines but much lower particulate numbers for both gasoline and CNG vehicles. Under these conditions, the gasoline particulate distribution has little structure but the CNG distribution is clearly bimodal. At higher loads, the number of particulates produced by diesel vehicles increases by an order of magnitude from idle and both the CNG and gasoline distributions are comparable in peak height. The diesel vehicle produces a much larger particulate volume than gasoline or CNG.

Sliding door designs are applied to rear side doors on vans and other large vehicles with a trend towards dual sliding doors with power operation. It is beneficial for the vehicle user to reduce the weight of and space occupied by these doors. Alcoa, in conjunction with Ford, has developed a multi-product, multi-material-based solution, which significantly reduces the cost of an aluminum sliding door and provides both consumer delight and stamping-assembly plant benefits. The design was successfully demonstrated through a concept readiness/technology demonstration program.

Future European air quality standards for light duty diesel vehicles will include stringent NOx emission regulations. In order to meet these regulations, a lean NOx catalyst system may be necessary. Since the catalytic removal of NOx is very difficult with the large concentration of oxygen present in diesel exhaust, a reductant is usually added to the exhaust to increase the NOx conversion. This paper describes a lean NOx catalyst system for a Transit light-duty truck which uses a reductant solution of urea in water. In this work, a microprocessor was used to vary the amount of the reductant injected depending on the operating conditions of a 2,5 L naturally aspirated HSDI engine. The NOx conversions were 60% and 80% on the current European driving cycle and the U.S. FTP cycles, respectively. Data on the emissions of HC, CO, NOx, particulate mass and composition, individual HC species, aldehydes, PAH and most HC species were evaluated.

After establishing the performance requirements and initial design assumptions, CAE concept models are used to set targets for major structural components to achieve desirable crash performance. When the designs of these major components become available they are analyzed in detail using nonlinear crash finite element models to evaluate their performance. All these components are assembled together later in a full car model to predict the overall vehicle crash performance. If the analysis shows that the targets are met, the design drawings are released for prototype fabrication. When CAE tools are effectively used, it will reduce product development cycle time and the number of prototypes. Crash analysis methodology has been validated and applied for steel automotive product development. Recently, aluminum is replacing steel for lighter and more fuel efficient automobiles. In general aluminum has quite different performance from steel, in particular with lower ductility.

This paper quantifies typical United States in-vehicle cowl area particulate filter parameters such as temperature, humidity and environmental conditions. Secondly, United States and Germany particulate filter fleet results will be included to help quantify the effect of loading on electret nonwoven particulate filter fractional efficiency and demonstrate the amount and types of particulate matter captured. Finally the paper will address the low submicron fractional filter efficiency of a simulated production “wet and dry” plate-fin automotive evaporator core.

The effect of temperature and preload on the bolt load retention (BLR) behavior of AZ91D and AE42 magnesium die castings was investigated. The results were compared to those of 380 aluminum die castings. Test temperatures from 125 to 175°C and preloads from 7 to 28 kN were investigated. The loss of preload for AZ91D was more sensitive to temperature than that observed for AE42, especially at low preloads. In general, retained bolt-load was lowest in AZ91D. All test assemblies were preloaded at room temperature and load levels increased when the assemblies reached test temperature. The load-increase was dependent on the preload level, test temperature, alloy, and results from thermal expansion mismatch between the steel bolt and the magnesium alloy components, mitigated by the onset of primary creep. Thermal exposure (aging) of AZ91D at 150°C improved BLR behavior.

Naturally aspirated Homogeneous Charge Compression Ignition (HCCI) operational window is very limited due to inherent issues with combustion harshness. Load range can be extended for HCCI operation using a combination of intake boosting and cooled EGR. Significant range extension, up to 8bar NMEP at 1000RPM, was shown to be possible using these approaches in a single cylinder engine running residual trapping HCCI with 91RON fuel with a 12:1 compression ratio. Experimental results over the feasible speed / load range are presented in this paper for a negative valve overlap HCCI engine. Fuel efficiency advantage of HCCI was found to be around 15% at 2.62bar / 1500RPM over a comparable SI engine operating at the same compression ratio, and the benefit was reduced to about 5% (best scenario) as the load increased to 5bar at the same speed.

This paper presents the design and operation of a new stepped bore master cylinder (fast-fill) which also integrates the rear brake proportioning valves and brake failure warning device in one major assembly. This design optimizes weight, performance and package together with several unique design features. It incorporates a combination of a plastic reservoir, permanent mold aluminum body, steel pistons, and minaturized steel proportioning valves resulting in a significant weight and cost reduction versus equivalent hydraulic actuation systems.

THE study of engine life, carried out by investigating engine wear in typical service, and by then striving to find the most effective ways of controlling it, forms the basis of this paper on contaminants in lubricants. The investigation involved a study of engine wear in 20,000 miles of operation typical of the average driver. The average driver was selected by using test cars from an employee transportation car pool. At the conclusion of the tests it was found that the use of the full-flow oil filter proved to be the best method for restricting engine wear caused by contaminants that get inside the engine. It was also shown that after successfully eliminating large, solid particles, further restriction of engine wear would depend upon the ability of the oil to lubricate, and upon the engine design to provide the oil supply in a manner suitable for lubrication of each part of the engine.

Flow fields generated during the intake stroke of a 4-stroke I.C. engine are studied experimentally using water analog simulation. The fluid is seeded by small flow tracer particles and imaged by two digital cameras at BDC. Using a 3-D Particle Tracking Velocimetry technique recently developed, the 3-D motion of these flow tracers is determined in a completely automated way using sophisticated image processing and PTV algorithms. The resulting 3-D velocity fields are ensemble averaged over a large number of successive cycles to determine the mean characteristics of the flow field as well as to estimate the turbulent fluctuations. This novel technique was applied to three different cylinder head configurations. Each configuration was run for conditions simulating idle operation two different ways: first with both inlet ports open and second with only the primary port open.

The requirements to produce high specific power, a high torque across a broad engine speed range and very low emissions levels have been seen as mutually exclusive in a conventional normally aspirated SI engine. Ford Motor Co in association with Cosworth Technology Ltd. have developed a port injection SI engine which achieves in excess of 63kW/ltr, a peak torque in excess of 97Nm/ltr, 92Nm/ltr between 2500rpm and 6500rpm and meets European IV and North American LEV emissions levels for the Focus ST170 in Europe and the SVT Focus in the US. To achieve the required torque across the speed range the volumetric efficiency needed to be maximized at all engine speeds. This was done by fitting continuously variable inlet valve timing, variable length intake manifold and a tuned exhaust manifold. To meet the emissions requirements, the catalyst light off time must be kept to a minimum.