Search Results

To achieve future fleet CO2 emission targets, all powertrain types, including those with internal combustion engines, need to achieve higher efficiency. Next to others the reduction of friction is one contributor to increase powertrain efficiency. The piston bore interface (PBI) accounts for up to 50 % of the total engine friction losses [1]. Optimizations in this area combined with the use of low viscosity oil, which can reduce the friction of further engine sub-systems, will therefore have a high positive impact. To assess the friction of the PBI whilst considering cross effects of other relevant parameters for mechanical function (e.g. blow-by & wear) and emissions (e.g. oil consumption) AVL has established a holistic development method based around the AVL FRISC (FRIction Single Cylinder) engine with a floating liner measurement concept.

As emission limits become increasingly stringent and the price of gaseous fuels decreases, more emphasis is being placed on promoting gas engines. In the field of large engines for power generation, dual fuel combustion concepts that run on diesel/natural gas are particularly attractive. Knock in diesel/natural gas dual fuel engines is a well known yet not fully understood complex phenomenon that requires consideration in any attempt to increase load and efficiency. Thus combustion concept development requires a reliable yet robust methodology for detecting knock in order to ensure knock-free engine operation. Operating parameters such as rail pressure, start of injection and amount of diesel injected are the factors that influence oscillations in the in-cylinder pressure trace after the start of combustion. Oscillations in the pre-mixed combustion phase, or ringing, are caused by the rapid conversion of large parts of the injected diesel.

High-pressure direct injection (HPDI) of natural gas into the combustion chamber enables a non-premixed combustion regime known from diesel engines. Since knocking combustion cannot occur with this combustion process, an increase in the compression ratio and thus efficiency is possible. Due to the high injection pressures required, this concept is ideally suited to applications where liquefied natural gas (LNG) is available. In marine applications, the bunkering of and operation with LNG is state-of-the-art. Existing HPDI gas combustion concepts typically use a small amount of diesel fuel for ignition, which is injected late in the compression stroke. The diesel fuel ignites due to the high temperature of the cylinder charge. The subsequently injected gas ignites at the diesel flame. The HPDI gas combustion concept presented in this paper is of a monovalent type, meaning that no fuel other than natural gas is used.

Hydrogen is seen as a promising energy carrier for a future mobility scenario. Applied as fuel in IC engines with internal mixture formation, hydrogen opens up new vistas for the layout of the combustion system. The 3D CFD simulation of internal mixture formation as well as combustion helps to understand the complex in-cylinder processes and provides a powerful tool to optimize the engine's working cycle. The performance of standard simulation models for mixture formation as well as the performance of a user-defined combustion model applied in a commercial CFD-code is discussed within this article. The 3D CFD simulations are validated with measurements obtained from a thermodynamic and from an optical research engine respectively.

In a variety of applications, two-stroke engines assert their usage as a propulsion unit, for examples in off-road vehicles, scooters, hand-held power tools and others. The outstanding power to weight ratio is the key advantage for two-stroke engines. Furthermore, two-stroke engines convince with high durability and low maintenance demand. However, an increasing environmental awareness, the protection of health and the shortage of fossil resources are the driving factors to further enhance the internal combustion process of two-stroke engines. The reduction of emissions and fuel consumption with a constant power level is focused on. Developments deal with the optimization of the combustion process itself or the enhancement of the exhaust gas aftertreatment. Especially in very small two-stroke engines an exhaust gas aftertreatment system is rarely applied, due to disadvantages regarding component temperatures and product costs.

Optimization of engine warm-up behavior has traditionally made use of experimental investigations. However, thermal engine models are a more cost-effective alternative and allow evaluation of the fuel saving potential of thermal management measures in different driving cycles. To simulate the thermal behavior of engines in general and engine warm-up in particular, knowledge of heat distribution throughout all engine components is essential. To this end, gas-side heat transfer inside the combustion chamber and in the exhaust port must be modeled as accurately as possible. Up to now, map-based models have been used to simulate heat transfer and fuel consumption; these two values are calculated as a function of engine speed and load. To extend the scope of these models, it is increasingly desirable to calculate gas-side heat transfer and fuel consumption as a function of engine operating parameters in order to evaluate different ECU databases.

Worldwide increasing energy consumption, decreasing energy resources and continuous restriction of emission legislation cause a rethinking in the development of internal combustion engines and fuels. Alternative renewable fuels, so called bio-fuels, have the potential to contribute to environmentally friendly propulsion systems. This study concentrates on the usage of alcohol fuels like ethanol, methanol and butanol in non-automotive high power engines, handheld power tools and garden equipment with the focus on mixture formation and cold start capability. Although bio-fuels have been investigated intensely for the use in automotive applications yet, the different propulsion systems and operation scenarios of nonautomotive applications raise the need for specific research. A zero dimensional vaporization model has been set up to calculate the connections between physical properties and mixture formation.

Dual fuel combustion processes, which burn varying ratios of natural gas and diesel, are an attempt to reach high efficiencies similar to diesel engines while exploiting the CO2 savings potential of natural gas. As shown in earlier studies, the main challenge of this combustion process is the high emission of unburned hydrocarbons during low load operation. Many publications have focused on a layout which utilizes port injection of natural gas and a direct injection of diesel to initiate combustion. However, previous studies indicated that a sequential direct injection of both fuels is more promising. It enables charge stratification of natural gas and air, whereby a remarkable reduction of the unburned hydrocarbon emissions was observed. This work develops this approach further, utilizing a low pressure direct injection of natural gas.

Charge dilution by lean-burn is one way to increase the efficiency of spark ignition engines while reducing NOx emissions. This work focuses on increasing the flammability of lean mixtures inside a passive pre-chamber spark plug by elevating its temperature with the help of a controllable hot surface integrated into the pre-chamber. Thus, an extension of the lean limit under part load is aimed for. A pre-chamber spark plug prototype with an integrated, controllable glow plug was developed, called Hot Surface Assisted Spark Ignition (HSASI). Experimental investigations were conducted on a single-cylinder engine at the Karlsruhe University of Applied Sciences. Operating modes with an active glow plug (HSASI) and a non-active glow plug were compared. The lean limit for both operation modes were determined under part load. NOx, CO and THC emissions were measured for different air-fuel equivalence ratios λ. The lean limit is extended by more than 0.1 in λ at low loads with HSASI operation.

Hydrogen is frequently cited as a future energy carrier. Hydrogen allows a further optimization of internal combustion engines, especially with direct injection. In order to assess various concepts, detailed thermodynamic analyses were carried out. Effects, which can be neglected with conventional fuels (e.g. losses due to injection during compression stroke) are considered. These basics as well as several results from test bed investigations are described within this article. Wall heat losses were found to have a major influence on overall efficiency and are thus investigated in detail, based on local surface temperature measurement. Finally, concepts that allow an increase in engine efficiency and lowest NOx emissions are demonstrated.

As alternative to electrification or carbon free fuels such as hydrogen, CO2-neutral fuels have been researched aiming to decrease the impact of fossil energy sources on the environment. Despite the potential benefit of capturing CO2 emission after combustion for own fuel production, the so-called eFuels also benefit by using a green source of energy during their fabrication. Among all the possibilities for eFuels, alcohols, ethers (such as MTBE and ETBE) and alternative hydrocarbons have shown positive impacts regarding emission reduction and performance when compared to standard gasoline. Previously in [1] and [2], synthetic fuels and methanol blends were tested at steady state conditions in order to verify advantages and drawbacks relative to gasoline, for power-sport motorcycles.

Small displacement two-stroke engines are cheap and low-maintenance propulsion systems and commonly used in scooters, recreation vehicles and handheld power-tools. The restriction by emission legislation and the increasing environmental awareness of end users as well as decreasing energy resources cause a rethinking in the development of propulsion systems and fuels in these fields. Despite recent improvements of electric powertrains, two stroke engines are the challenged propulsion system in high performance handheld power tools at the moment. The reasons are the extraordinary high power to weight ratio of two-stroke engines, the high energy density of liquid fuels and the reliability of the product with respect to extreme ambient conditions. Nevertheless, further improvements on emissions and fuel consumption of small displacement two-stroke engines can be realized.

Small engines for non-automotive applications include 2-stroke and 4-stroke gasoline engine concepts which have a reduced number of sensors due to cost and packaging constraints. In order to cope with future emission regulations, more sophisticated engine control and monitoring becomes mandatory. Therefore, a cost-effective way has to be found to gain maximum information from the existing sensors and actuators. Due to an increasing bio-fuel share in the market, the detection of bio-fuel content is necessary to guarantee a stable combustion by adapting the injection and ignition control strategy. Meaningful information about the combustion can be retrieved from combustion chamber ion current measurements. This paper proposes a general overview of combustion process monitoring in different engine concepts by measuring the ion current during combustion.

Using natural gas as a fuel in internal combustion engines is a promising way to obtain efficient power generation with relatively low environmental impact. Dual fuel operation is especially interesting because it can combine the safety and reliability of the basic diesel concept with fuel flexibility. To deal with the greater number of degrees of freedom caused by the interaction of two fuels and combining different combustion regimes, it is imperative to use simulation methods in the development process to gain a better understanding of the combustion behavior. This paper presents current research into ignition and combustion of a premixed natural gas/air charge with a diesel pilot spray in a large bore diesel ignited gas engine with a focus on 3D-CFD simulation. Special attention was paid to injection and combustion. The highly transient behavior of the diesel injector especially at small injection quantities poses challenges to the numerical simulation of the spray.

Hydrogen nowadays is considered one promising energy carrier for future mobility scenarios. Its application as a fuel in ICEs greatly benefits from Direct Injection (DI) strategies, which help to reduce the disadvantages of PFI systems such as air displacement effects, knocking, backfiring and low power density. In SI-engines one appropriate way to increase efficiency is the reduction of wall heat losses by jet- and/or wall-guided mixture formation systems. In theory, Compression Ignition (CI) systems employing a diffusion type of combustion allow for a significant raise in compression ratio and, thus, are likely to excel the SI concept in terms of efficiency. The following paper deals with results obtained from investigations on H2 Compression-Ignition (H2-CI) combustion systems by employing both thermodynamic research engines and 3D CFD simulation.

This paper presents an analysis of the potential of E85 (a mixture of 85 % (bio)ethanol and 15 % gasoline) as a fuel for spark-ignition (SI) direct-injection internal combustion engines. This involves investigation of not only application to downsizing concepts with high specific power but also behavior relating to emissions and efficiency at both part and full load. Measurements while running on gasoline were used for comparison purposes. The first stage involved analysis using 1D simulation of two different downsizing concepts with regard to turbocharging potential and performance. Following this, various influential parameters such as injector position, injection pressure, compression ratio, degree of turbocharging etc. were investigated on a single cylinder research engine. In the case of high pressure direct injection, particulate emissions also play an important role, so particulate count and particulate size distribution were also studied in detail.

Synergies in infrastructure and customer acceptance can be achieved by running internal combustion engines on mixtures of hydrogen and natural gas. Alongside the bridging effect between natural gas and hydrogen, such mixing offers advantages in terms of reduced emissions and improvements to the combustion process. The wide ignition limits and high flame speed of hydrogen have as positive an impact on the combustion of H2NG mixture as does the higher energy density of natural gas on range. A bi-fuel gasoline-natural gas vehicle was adapted to operation with gasoline, natural gas, hydrogen and any H2NG mixtures. For that purpose, the intake manifold was replaced by an aluminum construction, the injectors were replaced and the ECU had to be adjusted. Essentially quality-controlled hydrogen operation was possible throughout the engine map.

It is critical for gas and dual fuel engines to have improved transient characteristics in order that they can successfully compete with diesel engines. Testing of transient behavior as well as of different control strategies for the multi-cylinder engine (MCE) should already be done on the single cylinder engine (SCE) test bed during the development process. This paper presents tools and algorithms that simulate transient MCE behavior on a SCE test bed. A methodology that includes both simulation and measurements is developed for a large two-stage turbocharged gas engine. Simple and fast models and algorithms are created that are able to provide the boundary conditions (e.g., boost pressure and exhaust back pressure) of a multi-cylinder engine in transient operation in real-time for use on the SCE test bed. The main models of the methodology are discussed in detail.

Discussions about the optimal technology of propulsion systems for future ground vehicles have been raising over the last few years. Several options include different types of technologies. However, those who are advocating conventional internal combustion engines are faced with the fact that fossil fuels are limited. Others favor hydrogen fuel as the solution for the future, either in combination with combustion engines or as an energy carrier for fuel cells. In any case, the production and storage of hydrogen is an ongoing challenge of numerous research works. Finally, there are battery-electric or hybrid propulsion systems in use, gaining more and more popularity worldwide. Ongoing advances in power electronics help to improve control systems within automotive applications. New developed or designed components enable more efficient system architectures and control.

Focus is pointed on the highly favorable physical properties of hydrogen (H2) with regard to its combustion characteristics in internal combustion engines. Thereby it will be shown in how far the performance of next generation hydrogen engines can be improved by implementing a direct fuel injection system instead of the conventional port injection approach. Results from numerical as well as from experimental investigations will be used to clearly give a vision of the overall future potential of hydrogen for combustion engines in comparison to fuel cell systems.