Search Results

A full vehicle of a preview control semi-active suspension system based on an interval type-2 fuzzy controller design using a magnetorheological (MR) damper to improve ride comfort is investigated in this paper. It is integrated with the force distribution system to obtain the optimal rate of road adhesion during braking and handling. The nonlinear suspension model is derived by considering vertical, pitch, and roll motions. The preview interval type-2 fuzzy technique is designed as a system controller, and it is attached with a Signum function method as a damper controller to turn on the voltage for the MR damper. This voltage is adjusted for each wheel based on the external excitation generated by road roughness in order to enhance ride comfort. To describe the effectiveness and adaptable responses of the preview controlled semi-active system, the performance is compared with both the passive and MR passive suspension systems during time and frequency domains.

Vehicle Handling performance depends on many parameters. One of the most important parameters is the dynamic behavior of the steering system. However, steering system had been enhanced thoroughly over the past decade where Active Front Steering (AFS) is now present and other system as Active Independent Front Steering (AIFS) is currently in the research phase. Actually, AFS system adopt the front wheels’ angles base on the actual input steering angle from the driver according to vehicle handling dynamics performance. While, the AIFS controls the angle of each front wheel individually to avoid reaching the saturation limits of any of the front wheels’ adhesion. In this paper modeling and analysis of an AIFS is presented with Tire Work Load (TWL) based controller. Magic Formula tire model is implemented to represent the tire in lateral slip condition.

This paper is concerned with the analysis of the performance of actively suspended vehicles when the effects of the aerodynamics are considered. The investigation is wholly theoretical and treats a half vehicle model, active suspension, through simulation of running at different speeds on a random-profile road. Using classical control laws, which do not account for aerodynamic effects, it is shown that starting from a vehicle speed of 35 m/s, ride comfort and road holding parameters significantly deteriorate. A method is introduced to modify the control strategy so that these effects can be taken into consideration. Various forms of control laws are presented, and conclusions are drawn to specify the benefits that could be achieved from this modified control strategy.

The latest developments in the engine’s design aim to maximize the power output, downsize the engine, and minimize the fuel consumption. This paper investigates the thermomechanical loads on the piston of a turbocharged diesel engine. The main emphasis is the effect of increasing the boosting pressure on the piston loading until the possible maximum engine power is achieved. Also, it proposes the modification of the piston design in order to increase the durability for more power loading and decrease the total mass. The temperature distribution on the piston body, the corresponding thermomechanical deformations, the stress distribution, and the safety factor is excessively calculated. Finite element methods (ANSYS workbench) is used to analyze the thermomechanical loads applied to a three-dimensional model. The study is applied to the piston of a 300 hp diesel engine (base case) in order to increase the engine power by 17% (upgraded one).

This study presents a practical theoretical method to judge the aerodynamic response of buses in the early design stage based on both aerodynamic and design parameters. A constant longitudinal velocity 2-DOF vehicle lateral dynamics model is used to investigate the lateral response of a bus under nine different wind gusts excitations. An appropriate 3-D CFD simulation model of the bus shape results is integrated with carefully chosen design parameters data of a real bus chassis and body to obtain vehicle lateral dynamic response to the prescribed excitations. Vehicle model validity is carried out then, the 2-DOF vehicle lateral dynamics model has been executed in MATLAB Simulink environment with the selected data. Simulation represents the vehicle in a straight ahead path then entered a gusting wind section of the track with a fixed steering wheel. Vehicle response includes lateral deviation (LD), lateral acceleration (LA), yaw angle (YA) and yaw rate (YR).

Nonparametric models do not require any assumptions on the underlying input/output relationship of the system being modeled so that they are highly useful for studying and modeling the nonlinear behaviour of Magnetorheological (MR) fluid dampers. However, the application of these models in semi-active suspension is very rare and most theoretical works available on this topic address the application of parametric models (e.g. Modified Bouc-Wen model). In this paper, a nonparametric MR damper model based on the Restoring Force Surface technique is applied in vehicle semi-active suspension system. It consists of a three dimensional interpolation using Chebyshev orthogonal polynomial functions to simulate the MR damper force as a function of the displacement, velocity and input voltage. Also, a damper controller based on a Signum function method is proposed, for the first time, for use in conjunction with the system controller of a semi-active vehicle suspension.

A non-linear mathematical model of a semi-active (2DOF) vehicle suspension using a magnetorheological (MR) damper with information concerning the road profile ahead of the vehicle is proposed in this paper. The semi-active vibration control system using an MR damper consists of two nested controllers: a system controller and a damper controller. The fuzzy logic technique is used to design the system controller based on both the dynamic responses of the suspension and the Padé approximation algorithm method of a preview control to evaluate the desired damping force. In addition, look-ahead preview of the excitations resulting from road irregularities is used to quickly mitigate the effect of the control system time delay on the damper response.

This study deals with the mitigation of the vibration of the structure using a compound mass liquid column damper (MLCD). To study the damping efficiency of the MLCD, the mathematical model of the single degree of freedom structure integrated with MLCD including the damping due to the moving mass in the horizontal portion of the damper is derived. The equivalent-damping factor of the MLCD is determined by simulating the interaction between the moving mass and the liquid using the fluid-structure interaction (FSI) technique. A 3D FSI model is solved numerically using the ANSYS Workbench-CFX package. The global search optimization algorithm is applied to find the optimum tuning frequency and the optimum mass diameter ratio over a wide range of mass ratio and excitation amplitude. The optimization issue is solved with considering the limits of the maximum displacement of the liquid and the mass.

This research aims to model and assess autonomous vehicle controller while including a four-wheel steering and longitudinal speed control. Such a modeling process simulates human driver behavior with consideration of real vehicle dynamics’ characteristics during standard maneuvers. However, a four-wheel steering control improves vehicle stability and maneuverability as well. A three-degree of freedom bicycle model, lateral deviation, yaw angle, and longitudinal speed is constructed to describe vehicle dynamics’ behavior. Moreover, a comprehensive traction model is implemented which includes an engine, automatic transmission, and non-linear magic formula tire model for simulation of vehicle longitudinal dynamics. A combination of proportional integral derivative (PID) longitudinal controller and fuzzy lateral controller are implemented simultaneously to track the desired vehicle path while minimizing lateral deviation and yaw angle errors.

The work presented here is to develop a monitoring life mathematical model to manage periodically the operations job orders of vehicle service station. This period is occasionally an hour, a day or a longer period than that, and is normally determined by the service manager. Model parameters are changeable over these periods due to dynamic movable situation of a vehicle markets. The objective function is to maximize the total income from vehicles service operations at all considered conventional model or with self expert prognostic system by taken into account least stop of vehicles, while keeping in mind the satisfying the customer demands and the service quality. The decision variables indicate the number of various technical operations to be performed for different types of vehicles.

Dynamic modeling of the gear vibration is a useful tool to study the vibration response of a geared system under various gear parameters and operating conditions. An improved understanding of vibration signal is required for early detection of incipient gear failure to achieve high reliability. However, the aim of this work is to make use of a 6-degree-of-freedom gear dynamic model including localized tooth defect for early detection of gear failure. The model consists of a gear pair, two shafts, two inertias representing load and prime mover and bearings. The model incorporates the effects of time-varying mesh stiffness and damping, backlash, excitation due to gear errors and modifications. The results indicate that the simulated signal shows that as the defect size increases the amplitude of the acceleration signal increases. The crest factor and kurtosis values of the simulated signal increase as the fault increases.

In order to achieve the high capability of the ride comfort and regulating the tire slip ratio, a preview of a nonlinear semi-active vibration control suspension system using a magnetorheological (MR) fluid damper is integrated with traction control in this paper. A controlled semi-active suspension system, which consists of the system controller and damper controller, was used to develop ride comfort, while the traction controller is utilized to reduce a generated slip between the vehicle speed and rotational rate of the tire. Both Fractional-Order Filtered Proportional-Integral-Derivative (P¯IλDμ) and Fuzzy Logic connected either series or parallel with P¯IλDμ are designed as various methodologies of a system controller to generate optimal tracking of the desired damping force. The signum function method is modified as a damper controller to calculate an applied input voltage to the MR damper coil based on both preview signals and the desired damping force tracking.

Vehicle suspension is considered a vital system of modern automotive and necessary to offer an adequate level of ride comfort and roadholding. In the present paper, a fuzzy-based sliding surface (FBSS) controller is designed, as a system controller for the first time, for a semi-active vehicle suspension using a magnetorheological (MR) damper in order to minimize the transmitted unwanted vibrations to the passengers. Therefore, an ideal reference skyhook model is employed to construct the sliding surface, which is the input of fuzzy logic. MR damper is a semi-active device and is controlled indirectly using an external voltage source. So a neural-based damper controller is used to compute the applied voltage to the magnet coil of the MR damper in series with the FBSS system controller. The proposed semi-active controlled quarter-vehicle suspension using an MR damper is solved numerically by Matlab.

The purpose of this paper is to investigate the efficiency of a quarter car semi-active suspension system with the state-derivative feedback controller using the Bouc-Wen model for magneto-rheological fluids. The magnetorheological (MR) dampers are classified as adaptive devices because of their characteristics can be easily modified by applying a controlled voltage signal. Semi-active suspension with MR dampers combines the benefits of active and passive suspension systems. The dynamic system captures the basic performance of the suspension, including seat travel distance, body acceleration, passenger acceleration, suspension travel distance, dynamic tire deflection and damping force. With minimal reliance on the use of sensors, the investigation aims to improve ride comfort and vehicle stability. In this study, the state derivative feedback controller and Genetic algorithm (GA) is utilized to improve the performance of semi-active suspension system.

E-spring is a recent innovation in vehicle suspension springs. Its behavior and characteristics are investigated experimentally and verified numerically. The mechanical and frequency-response-based properties of E-springs are investigated experimentally at both of the structural and constitutional levels. Thermoplastic-based and thermoset-based fibrous composite structures of the E-springs are modified at micro-scale with various additives and consequently they are compared. The experimental results reveal that additives of micrometer-sized particles of mineral clay to an ISO-phthalic polyester resin of the composite E-spring can demonstrate distinguished characteristics. A hybrid approach of the inter-laminar shear stress and Tsai-Wu criteria is implemented in order to identify failure indices numerically at the utmost level of loading and verify the experimental results.

A hybrid search optimization is presented in order to optimize hybrid laminated fibrous composite E-springs for vehicle suspension systems. This optimization is conducted with both of the geometrical configuration and laminate structure of the E-spring. A genetic algorithm along with a hill-climbing random-walk approach are used through a developed NURBS-based technique in order to conduct this optimization. A mathematical-modeling-based mid-ware technology is introduced in order to fully automate the optimization process through linking the run engines of mathematical modeling and finite element analysis from within the mathematical modeling engine. A hybrid approach of the inter-laminar shear stress and Tsai-Wu criteria is first implemented in order to identify failure indices of the resulting optimum shape and laminate structure.

Adaptive neuro-fuzzy inference system (ANFIS) technique has been developed and applied by numerous researchers as a very useful predictor for nonlinear systems. In this paper, non-parametric models have been investigated to predict the direct and inverse nonlinear dynamic behavior of magnetorheological (MR) fluid dampers using ANFIS technique to demonstrate more accurate and efficient models. The direct ANFIS model can be used to predict the damping force of the MR fluid damper and the inverse dynamic ANFIS model can be used to offer a suitable command voltage applied to the damper coil. The architectures and the learning details of the direct and inverse ANFIS models for MR fluid dampers are introduced and simulation results are discussed. The suggested ANFIS models are used to predict the damping force of the MR fluid damper accurately and precisely. Moreover, validation results for the ANFIS models are proposed and used to evaluate their performance.

The dynamics of vehicles became one of the most important aspects for current developments of electronically controlled steering, suspension and traction/braking systems. However, most of the published research on vehicle maneuverability doesn't take into account the effect of the dynamic tire load and its variation on uneven roads. Clearly, it was stated that using a suitable active suspension system could reduce this dynamic tire load. This dynamic tire load is playing a vital role as it is the major link between the vertical and lateral forces exerted on the road, which affects the lateral dynamics of the vehicle. In this paper, a practical hydro-pneumatic limited bandwidth active suspension system with and without wheelbase preview control is used to study its influence on the vehicle stability in lateral direction. The model is a longitudinal half car with four degrees of freedom.

The transformation of rapeseed oil into methyl ester through the transestrification process normally produce biodiesel fuel with kinematic viscosity almost double that of the commercial diesel fuel. The bulk modulus of biodiesel is also higher than that for the conventional diesel fuel. In this paper, the effects of the two physical properties on the injection characteristics of Rapeseed Methyl Ester (RME) are discussed. The injection characteristics considered here were namely; nozzle chamber pressure, needle lift, and fuel injection rate. The mutual effects of engine speed and delivery pipe length were also analyzed. A previously developed computer model was used to simulate the injection process of the conventional pump-line-nozzle injection system. An explicit finite difference scheme was adopted to solve the unsteady flow equation within the delivery pipe.

In this work the effects of vehicle vertical vibrations on the tires/road cornering forces, and then consequently on vehicle lateral dynamics are studied. This is achieved through a ride model and a handling model linked together by a non-linear tire model. The ride model is a half vehicle with four degrees of freedom (bounce and pitch motions for vehicle body and two bounce motions for the two axles). The front and rear suspension are a hydro-pneumatic slow-active systems with 6 Hz cut-off frequency designed based on linear optimal control theory. Vehicle lateral dynamics is modeled as two degrees (yaw and lateral motions) incorporating a driver model. An optimal rear wheel steering control in addition to the front steering is considered in the vehicle model to represent a Four Wheel Steering (4WS) system. The tire non-linearity is represented by the Magic Formula tire model.