Search Results

To enable non-throttling operation of gasoline S.I. engine, we have manufactured engines equipped with a newly developed Hydraulic Variable-valve Train (HVT), which can vary its intake-valve closing-timing freely. The air-intake control ability of HVT engine is equivalent to conventional throttling engines. Combustion becomes unstable, however, under non-throttling operation at idling. For the countermeasure, newly designed combustion chamber has been developed. The reduction of pumping loss by the HVT depends on engine speed rather than load, and amounts to about 80 % maximum. A conventional engine-management system is not applicable for non-throttling operation. Therefore, new management system has been developed for load control.

This paper reports on DaimlerChrysler's participation in the Ad Hoc Diesel Fuels Test Program. This program was initiated by the U.S. Department of Energy and included major U.S. auto makers, major U.S. oil companies, and the Department of Energy. The purpose of this program was to identify diesel fuels and fuel properties that could facilitate the successful use of compression ignition engines in passenger cars and light-duty trucks in the United States at Tier 2 and LEV II tailpipe emissions standards. This portion of the program focused on minimizing engine-out particulates and NOx by using selected fuels, (not a matrix of fuel properties,) in steady state dynamometer tests on a modern, direct injection, common rail diesel engine.

We developed a copper catalyst using zero Platinum group metals (hereafter PGMs) to fit motorcycle specific emission gas environment. Though many research reports to develop catalyst without using PGMs that are precious and costly resources are available, no reports had proven Base Metal Catalyst development to meet actual emission regulation equivalent to PGM catalysts. Compared to conventional PGM catalysts, higher temperature is required to keep high catalytic conversion efficiency by utilizing properties of this Base Metal Catalyst. Thus, this Base Metal Catalyst is located in cross coupling position, though it is rare case in motorcycle. This catalyst location could cause negative impacts on engine knocking, engine performance and drivability. This time, to overcome such negative impacts we optimized whole exhaust system, including parts around catalyst.

Into the early-part of the next century, automotive emission standards are becoming stricter around the world. The electrically-heated catalyst (EHC) is well known as an effective technology for the reduction of cold-start hydrocarbon emissions without a significant increase in back pressure. Our extruded, alternator powered EHC (APEHC) manufactured with a unique canning method and equipped with a reliable, water proof electrode has demonstrated excellent durability and reliability, as stated in our previous SAE paper (#960340). The APEHC system discussed in this paper has achieved the Ultra-Low-Emission Vehicle (ULEV) standards, after 100,000 miles of fleet testing, without any failure. This is the final milestone in addressing the EHC as a realistic-production technology for ULEV. With the ability to meet ULEV/Stage III emission targets without a significant increase in back pressure, the EHC will be applied to an especially high performance vehicle with a large displacement engine.

In recent years, fuel efficiency has been improved by using many technologies such as downsizing engine, turbocharger and direct injection to reduce CO2 emissions from vehicle. However, the temperature of the exhaust gas from the engines using these technologies becomes lower than that form conventional one. That increases the difficulty for three-way catalyst (TWC) to purify CO, HC and NOx enough because TWC is not warmed up just after engine starting. In order to reduce cold emission mentioned above, we have been studying the warmup strategy of which the key property is thermal mass of TWC. To achieve early warmup, thermal mass of TWC is reduced by lightening the weight of (1) substrate and (2) catalytic materials, namely washcoat amount. Along with the strategy, we have developed TWC with lightweight substrate and applied it from the 2016 model year CIVIC.

This research is aimed at development of the catalyst for gasoline automobiles which uses only palladium (Pd) among platinum group metals (PGMs). And the conformity emission category aimed at LEV III-SULEV30. For evaluation, the improvement effect was verified for 2013 model year (MY) ACCORD (LEV II-SULEV) as the reference. As compared with Pd-rhodium (Rh) catalyst, a Pd-only catalyst had the low purification performance of nitrogen oxides (NOx), and there was a problem in the drop in dispersion of Pd by sintering, and phosphorus (P) poisoning.

Aiming for higher output power, greater fuel economy and reduced exhaust emissions, a new V-6 3.5-liter i-VTEC Variable Cylinder Management (VCM) engine has been developed. This engine uses a cylinder-deactivation mechanism with VTEC technology that allows the number of cylinders to be controlled in three modes (three, four or all six cylinders), according to the operating conditions. This adds a four-cylinder mode to the conventional cylinder- deactivation engine. In addition to increasing the number of cylinder- deactivation modes, the new hydraulic circuits, a hydraulic pressure switching mechanism and a switchover control were also developed. These make it possible to instantaneously switch the active cylinders without impairing drivability, in the same manner as a conventional engine.

In order to contribute to the resolution of global environmental problems and to respond to the issue of diminishing resources, the Civic Hybrid, a hybrid passenger automobile has been developed to achieve both low emissions and low fuel consumption. The hybrid system takes the conventional Honda IMA (Integrated Motor Assist) system as its foundation. 4-cylinder, 1.3L SOHC, 2-plug engine i-DSI (DSI: Dual and Sequential Ignition) has been selected and modified for lean burn combustion. In addition, a cylinder idling system to increase the amount of electrical energy regenerated during deceleration has been adopted, among other technology. The ultra-thin DC brushless motor has been modified with its magnetic circuit to improve maximum regenerative torque by approximately 30%. Thanks to a new power train that improves CVT transfer efficiency, low fuel consumption of 48mpg in the city and 47mpg on the highway (the 5MT vehicle is 46mpg in the city and 51mpg on the highway) is achieved.

With the increasing number of automobiles, the worldwide problem of air pollution is becoming more serious. The necessity of reducing tail-pipe emissions is as high as ever, and in countries all over the world the regulations are becoming stricter. The emissions at times such as after engine cold start, when the three-way catalyst (TWC) has not warmed up, accounts for the majority of the emissions of these pollutants from vehicles. This is caused by the characteristic of the TWC that if a specific temperature is not exceeded, TWC cannot purify the emissions. In other words, if the catalyst could be warmed up at an early stage after engine start, this would provide a major contribution to reducing the emissions. Therefore, this research is focused on the substrate weight and investigated carrying out major weight reduction by making the porosity of the substrate larger than that of conventional products.

Recently, automotive emission regulations are being further tightened, such as the Tier III/LEV III in the U.S. As a result, reducing cost of after-treatment systems to meet these strict regulations has become an urgent issue, and then the demand for high-precision air-fuel ratio (A/F) control which can achieve this cost reduction is high [1]. On the other hand, in order to meet rapidly changing market needs, it is becoming difficult to keep enough development periods that enable sufficient calibration by trial-and-error, such as feedback-gain calibration. This leads to an increase in three-way catalytic converter costs in some cases. For these reasons, it is necessary to construct control system that can make full use of hardware capabilities, can shorten development periods regardless of the skill level of engineers.

Measuring the real-world performance of emission control technologies is an important aspect in the development of advanced low-emission vehicles. In addition, data acquired from such measurements can be used to improve the accuracy of air quality predictive models. Honda has developed an on-board sampling/analysis system capable of measuring on-road emissions at ULEV levels and below. Ambient air can be analyzed simultaneously. This FTIR-based system can measure several species; this paper will focus on NMHC, NOX, and CO. Techniques were developed to address the challenges associated with acquiring accurate real-time data at concentrations below 1 ppm in an on-road vehicle. Validation studies performed with reference gases and vehicle exhaust indicate a very good correlation between the on-road analyzer system and classic bench methods for all target compounds. Dynamic studies performed by the University of California, Riverside, also show good correlation.

The Automotive Industry/Government Emissions Research CRADA (AIGER) has been working to develop a new methodology for the direct determination of nonmethane hydrocarbons (DNMHC) in vehicle testing. This new measurement technique avoids the need for subtraction of a separately determined methane value from the total hydrocarbon measurement as is presently required by the Code of Federal Regulations. This paper will cover the historical aspects of the development program, which was initiated in 1993 and concluded in 2002. A fast, gas chromatographic (GC) column technology was selected and developed for the measurement of the nonmethane hydrocarbons directly, without any interference or correction being caused by the co-presence of sample methane. This new methodology chromatographically separates the methane from the nonmethane hydrocarbons, and then measures both the methane and the backflushed, total nonmethane hydrocarbons using standard flame ionization detection (FID).

The two liter DOHC-VTEC engine developed for the Honda S2000 produces 179kW (240HP, which is 120HP per liter). It is the highest output power among all naturally aspirated two liter engines ever mass-produced. It also achieves an exhaust emission level within National LEV standards. The new engine utilizes a redesigned VTEC cylinder head, in which MIM (metal injection molding) rocker arms are used. The new cylinder block with a ladder frame structure for its lower part, a newly developed camshaft drive chain and gear system and a metal honeycomb catalyst with an air pump start-up system are also utilized.

With the total amount of air pollution caused by vehicle emissions on the increase, the problem has now became a global concern, and various regulatory measures have been put into effect in each region of the world. This is especially true in California, U.S.A, where countermeasures have been adopted early. There, the ULEV (Ultra Low Emission Vehicle) standard, which was ones deemed impossible for gasoline engines to meet, is now in effect. In response to these developments, Honda announced the ULEV system for a 2.2 liter gasoline engine with a closed-coupled catalytic converter (CC) and an under-floor catalytic converter (UF) at the beginning of 1995, and reported on the system's emission characteristics. 1) A new ULEV system has been developed based on the previous system but using only UF, aiming for marketable improvements in product characteristics such as higher output. The new system features the ultra low heat capacity and high heat insulating (ULOC) exhaust manifold.

With the adoption of the California Low-Emission Vehicle Regulations and the associated lower emission standards such as LEV (Low-Emission Vehicle in 1990), ULEV (Ultra-Low-Emission Vehicle), and LEV II (1998 with SULEV-Super Ultra Low Emission Vehicle), concerns were raised by emissions researchers over the accuracy and reliability of collecting and analyzing emissions measurements at such low levels. The primary concerns were water condensation, optimizing dilution ratios, and elimination of background contamination. These concerns prompted a multi-year research program looking at several new sampling techniques. This paper will describe the cooperative research conducted into one of these new technologies, namely the Bag Mini-Diluter (BMD) and Direct Vehicle Exhaust (DVE) Volume system.

Vehicle evaluations and model calculations were conducted on a vacuum-insulated catalytic converter (VICC). This converter uses vacuum and a eutectic PCM (phase-change material) to prolong the temperature cool-down time and hence, may keep the converter above catalyst light-off between starts. Tailpipe emissions from a 1992 Tier 0 5.2L van were evaluated after 3hr, 12hr, and 24hr soak periods. After a 12hr soak the HC emissions were reduced by about 55% over the baseline HC emissions; after a 24hr soak the device did not exhibit any benefit in light-off compared to a conventional converter. Cool-down characteristics of this VICC indicated that the catalyst mid-bed temperature was about 180°C after 24hrs. Model calculations of the temperature warm-up were conducted on a VICC converter. Different warm-up profiles within the converter were predicted depending on the initial temperature of the device.

For reduction of NOx and soot emission with conventional diesel diffusion combustion, the authors focused on enhancement of the rate of injection (hereafter referred to as RoI) to improve air availability, thus enhancing the fuel distribution and atomization. In order to increase opening ramp of the RoI (hereafter referred to as fast injection rate), a hydraulic circuit was improved and nozzle geometries were optimized to make the greatest use of the advantages of the hydraulic circuit. Two different common rail injectors were prepared for this research. One is a mass production-type injector with piezo actuator that achieved the EURO-V exhaust gas emission standards, and the other is a prototype injector equipped with the new hydraulic circuit. The nozzle needle of the prototype injector is directly actuated by high-pressure fuel from common rail to improve the RoI.

The College of Engineering-Center for Environmental Research and Technology at the University of California, Riverside and Honda Motor Company are conducting a cooperative research program to study the emission characteristics and evaluate the environmental impact of advanced technology vehicles designed to have emission rates at, or below, the California ULEV standard. This program involves a number of technical challenges relating to instrumentation capable of measuring emissions at these low levels and utilizing this instrumentation to gather data under realistic conditions that will allow assessments of the environmental impact of these advanced vehicle technologies. This paper presents results on the performance and suitability of a Fourier Transform Infrared (FTIR) based on-board measurement system developed principally by Honda R&D for this task. This system has been designed to simultaneously measure vehicle exhaust and ambient roadway pollutant concentrations.

Recently, emission regulations have been strict in many countries, and it is very difficult technical issue to reduce emissions of diesel cars. In order to reduce the emissions, various combustion technologies such as Massive EGR, PCCI, Rich combustion, etc. have been researched. The combustion technologies require precise control of the states of in-cylinder gas (air mass flow, EGR rate etc.). However, a conventional controller such as PID controller could not provide sufficient control accuracy of the states of in-cylinder gas because the air-pass system controlled by an EGR valve, a throttle valve, a variable nozzle turbo, etc. is a multi-input, multi-output (MIMO) coupled system. Model predictive control (MPC) is well known as the advanced MIMO control method for industrial process. Generally, the sampling period of industrial process is rather long so there is enough time to carry out the optimization calculation for MPC.

Honda has developed a new hybrid system targeting the C and D segments that aims for the latest environmental performance, high fuel economy, and enhanced acceleration feeling in driving. The new engine to be applied to this new hybrid system has been developed with the goal of expanding the high thermal efficiency range, realizing the latest environmental performance, and high quietness. The new engine has adopted the Atkinson cycle and cooled exhaust gas recirculation (EGR) carried over from the previous model [1], and employed an in-cylinder direct fuel injection system with fuel injection pressure of 35 MPa. The combustion chamber and ports have been newly designed to match the fuel system changes. By realizing high-speed combustion, the engine realized a high compression ratio with the mechanical compression ratio of 13.9.