Search Results

This paper describes an improved mathematical model to study the emission conversion effectiveness of a three-way catalytic converter, which employed detailed chemical reaction mechanism. The model also accounts for adsorption/release of oxygen in the catalyst monolith under non-stoichiometric A/F conditions. A commercial CFD code FLUENT was utilized to solve the governing equations for flow and pressure drop and to simulate the transient process in a three-way catalytic converter in a multi-dimensional manner. A comparison between simulation results and experimental data for a three-way catalyst was conducted and a good agreement was observed. Based on the improved model, some geometric parameters were studied for an elliptic monolith catalyst, which are widely used in today's converter systems because of its advantages in packaging.

To find out the main excitation sources of a bus floor's vibration, modal analysis and spectral analysis were respectively performed in the paper. First we tested the vibration modal of the bus's floor under the full-load condition, and the first ten natural frequencies and vibration modes were obtained for the source identification of the bus floor's vibration. Second the vibration characteristic of the bus floor was measured in an on-road experiment. The acceleration sensors were arranged on the bus's floor and the possible excitation sources of the bus, which includes engine mounting system, driveline system, exhaust system, and wheels. Then the on-road experiment was carefully conducted on a highway under the four kinds of test condition: in-situ acceleration, uniform velocity (90km/h, 100km/h, 110km/h, 120km/h), uniform acceleration with top gear, and stall sliding condition with neutral gear.

To meet more stringent emission regulations for diesel engines, diesel particulate filters (DPF) have been widely used for diesel engines. However, the DPF regeneration is a great challenge for fuel economy. In this paper, a mathematical model characterizing the microwave regeneration process of a wall-flow particulate filter is introduced to better understand the process. Based on this model, important parameters such as evolutions of the energy stream densities of microwaves, wall temperature, regeneration efficiency and the pressure drop in the filters, both cordierite and SiC, are investigated. These results can provide an important theoretical guide for optimizing and controlling the microwave regeneration process.

A 2-D gas-particle two-phase flow model has been developed to study the flow characteristics in a single channel of a honeycomb ceramic diesel particulate filter. A particle source in cell (PSIC) algorithm is used to calculate the gas-particle two-phase flow. Firstly, the gas-phase flow field alone (without taking into account of the particle-phase) is solved for estimation of gas velocity and pressure fields in the Euler coordinate. Secondly, the particle-phase is added in and particles tracked down in the Lagrange coordinate. Thirdly, the particle source which acts on the gas-phase cell is calculated and added to the gas-phase equations. Fourthly, the gas-phase equations with the particle source are solved again. Lastly, the above process is iterated until the flow field is convergent. Taking the above-mentioned approach, the gas-particle two-phase flow characteristic is simulated using FLUENT. The simulation results are in good agreement with experiment data.

A 3D grid model of engine brake is established for an automobile engine. The dynamic compression release braking process is simulated by using this model. In the process of engine braking, the movement of valve and piston causes changes of the internal flow field of the engine. In this paper, the movement of valve and piston were defined by using the dynamic grid technology, so that the numerical simulation is closer to the actual situation via the updating of grid. Based on the relevant parameters of compression release engine brake (including the opening of the exhaust valve, the engine speed and the exhaust back pressure), the pressure and power of the compression release braking system were simulated under the conditions of multiple operating conditions and experimental verification was carried out. The results showed that the braking works of the compression release engine brake are mainly from the compression stroke and the exhaust stroke.

This paper summarized the development methodology and technical experiences on Formula Student racecar engines acquired by Jilin University from 2011 to 2015. This series of engines are all based on 600cc 4-cylinder motorcycle gasoline engines and were modified to turbocharged engines which met the Formula Student technical regulations, in order to achieve higher power output, wider torque band as well as lower fuel consumption. During the development process, multiple research projects have been conducted surrounding the turbocharging technology. These research projects have covered multiple areas including the matching of the flow rate characteristics of the engine and the turbocharger, the design of intake and exhaust systems, research on the wastegate as well as its actuator, the tuning and control of the boost pressure as well as the design of the lubrication system for the turbocharger, etc.

With its advantages on cost and performance, the integrated exhaust manifold (casting with the turbine) is being used on more vehicles by auto makers. Generally, when compared with the divided exhaust manifold, the integrated exhaust manifold stands for higher vibratory excitation from gas dynamics. In this paper, the gas dynamics excitation has been computed through the GD (gas dynamics) software GT-Power which calculates the exhaust pipe surface pressure, and CFD code Star-CCM+ which calculates the turbine blade force. And the response of manifold has been solved under this excitation. On the other hand, the mechanical excitation has been computed through the MBD (multi-body dynamics) platform AVL-Excite-PU, and the responses under the gas excitation plus the mechanical load have been studied in order to analyze the effects of the fluid excitation on an integrated manifold.