Search Results

The purpose of this paper is to introduce a method to analyze the imaginary kingpin axis in multi-link type suspension mechanisms by using the Displacement Matrix method, the instantaneous screw axis theory, and the nonlinear equation solver “DESIGN”.[1][2] The mathematical logic and a Kinematic theory used in this method have been developed a long time ago. But the key point of this method is how accurate and effective we can get the information on design parameters related to the imaginary kingpin axis existing only in the multi-link type suspension, especially in the initial stage of suspension geometry design.

Customer vehicle usage monitoring is one of the most fundamental elements to consider in the process of developing a durable vehicle. The extant method to research customer vehicle usage takes considerable time and effort because it requires attaching a series of sensors to the vehicle-gyroscope, accelerometer, microphone, and GPS-to gather information through data logs and then to analyze data in a computer where designated analyzing software has been installed. To solve the problem, this paper introduces a new concept of integrated system developed to examine customer vehicle usage that can analyze data by collecting it from a variety of sensors installed on a smartphone.

To design an optimum engine intake system, a flow model for the intake manifold was developed by the method of characteristics. The flow in the intake manifold was one-dimensional, and finite difference equations were derived from the governing equations of flow. The thermodynamic properties inside a cylinder were found by the first law of thermodynamics, and the boundary conditions were formulated using a steady flow model. By comparing the calculated results with experimental data, the appropriate boundary conditions and convergence limits for a flow model were established. From this model, design variables for the intake system were investigated. The optimum manifold length became shorter when the engine speed were increased. The effect of intake valve timings on inlet air mass was also studied by this model. Advancing intake valve opening decreased inlet air mass slightly, and the optimum intake valve closing was found.

This paper discusses the effects of lubricant viscosity on the friction characteristics of engine bearing and cam/tappet which are the typical moving parts of an engine and operate in different lubrication regimes. Based on the measured crankshaft temperatures, we calculated the friction coefficient of the engine bearing according to Sommerfeld number by a simple heat equilibrium equation. The oil film thicknesses between cam and tappet were measured in a motored cylinder head which had a direct acting type overhead camshaft. The boundary and viscous friction components were estimated separately according to a parameter defined as the ratio of the central oil film thickness to the composite surface roughness. These two friction components were added to calculate the friction coefficient. Finally, the motoring friction torque was measured and compared with the estimated friction coefficient.

The verification of the durability for vehicle body and chassis components is a basic requirement for the vehicle development process. For this, automotive company performs durability test on the proving ground or predict the durability using CAE technology. The representative proving ground test that verifies the durability of vehicle body and chassis components are belgian(hereinafter B/G) and cross-country(hereinafter X/C) test road. The B/G test road verifies the durability of body and chassis components for periodic road load that the vehicle undergoes while travelling on a rough road with regular speed. The X/C test road is composed of squat, dive, bumping and bottoming test modes and this test verifies the durability under aperiodic road load. Because of the relatively long test load of X/C, the road load signal of X/C is too long and enormous to apply it to durability analysis.

Identification of structure borne sound sources induced by the structural vibration of an automotive powertrain has been studied. Based on the principal component analysis which uses singular value decomposition of a matrix consisting of the auto- and cross-spectra, the operating vibrational analysis is performed. The quantitative description of the output power due to intrinsic incoherent source is addressed. The applicability of the technique is tested both numerically and experimentally. First, the coherence analysis is numerically carried out with a simple structure which is modeled as multi-input and single output to identify the structure borne noise generation process. Second, the actual vibrational behavior of a powertrain structure and the interior noise analysis of a car under the running condition are carried out. The technique is shown to be very effective in the identification of the structure borne noise sources.

In this paper, an active type variable intake system is proposed, which improves both engine power and NVH performance. The proposed system uses a magnet valve to control the air path to the engine intake manifold. While other types of variable intake system such as vacuum actuator type or DC motor type need an ECU to control the valve, the proposed system only uses force equilibrium between magnetic force and vacuum pressure, resulting in weight and cost reduction. The system is composed of dual duct (duct A, duct B) and a magnet valve. In low RPM region, the magnet valve is closed and only duct A is used to supply air into the engine. In high RPM region the valve opens up and maximizes the amount of the air that goes into the engine intake manifold. The result is that the output power of the engine is maximized in high RPM region, as well as the NVH performance is improved in low RPM region.

Acoustics comfort is a key point for the ground transportation market and in particular in the automotive area. A significant contributor to the noise levels in the cabin in the range 200Hz to 3000Hz is the HVAC (Heating, Ventilating, and Air Conditioning) system, consisting of sub-systems such as the air intake duct, thermal mixing unit, blower, ducts, and outlet vents. The noise produced by an HVAC system is mainly due to aeroacoustics mechanisms related to the flow fluctuations induced by the blower rotation. The structure borne noise related to the surface induced vibrations and to the noise transmission through the dash or plastic panels may also contribute but is not considered in this study. This study presents a digital approach for HVAC aeroacoustics noise predictions related to the ducts and outlet vents. In order to validate the numerical method flow and acoustics measurements are performed on production HVAC systems placed in an anechoic room.

This paper outlines an improved methodology to perform calculations to verify the compliance of automotive door latch systems to minimum legal requirements as well as to perform additional due diligence calculations necessary to comprehend special cases such as roll over crashes and locally high inertial loadings. This methodology builds on the calculation method recommended by SAE J839 and provides a robust and clear approach for application of this method to cable release systems, which were not prevalent at the time J839 was originally drafted. This method is useful in and of itself but its utility is further increased by the application of the method to a Computer Aided Design (CAD) template (in this case for Catia V5), that allows some automation of the calculation process for a given latch type. This will result in a savings of time, fewer errors and allows for an iterative concurrent analysis during the design process.

Ground systems in automobiles become more important as more electric devices are installed and the amount of currents flowing increases. The performance of the devices depends on the ground voltage, which is generated between ground points by I-R voltage drops. Therefore, low ground voltages are required for the reduction of the unnecessary power dissipation as well as the reliable performance of the devices. In this paper, we propose an automotive ground system model to analyze ground structure and reveal the main cause of ground voltages. The equivalent resistor network model is presented to describe the relationship between ground points. Then, we validate the model by comparing the simulation results with the measurements in a real car. The presented analysis can provide guidance on designing a reliable ground system such as how to reduce the ground voltages for the proper operation of devices.

In this paper, we deal with the automatic climate control for Recreational Vehicle (RV). The HVAC system used for RV was composed of front side and rear side. And, the HVAC system of front side differed from that of rear side in the characteristic of HVAC system. This system was economically optimized for automatic control over 2 separated zones. The development procedure of automatic climate controller was as follows. The first stage was to derive control equation from characteristic analysis of HVAC system and the structural characteristic of vehicle interior. In the second stage, the software (S/W) was designed and programmed to operate microprocessor which calculated previously mentioned equation. Finally, the hardware (H/W) design and building were performed to operate the HVAC system with the calculation results from microprocessor. The control performance of this automatic climate control algorithm and system was evaluated by experimental method.

Polylactide (PLA), which is one of the most important biocompatible polyesters that are derived from annually renewable biomass such as corn and sugar beets, has attracted much attention for automotive parts application. The manufacturing method of PLA is the ring-opening polymerization of the dimeric cyclic ester of lactic acid, lactide. For the PLA composites including stereocomplexed with L- and D-PLA, we developed the unit processes such as fermentation, separation, lactide conversion, and polymerization. We investigated D-lactic acid fermentation with a view to obtaining the strains capable of producing D-lactic acid, and through catalyst screening test for polycondensation and depolymerization reactions, we got a new method which shortens the whole reaction time of lactide synthesis step. Poly(d-lactide) is obtained from the ring-opening polymerization of d-lactide. Also we investigated several catalysts and polymerization conditions.

In order to improve the fuel consumption ratio of the vehicle, a great deal of research is being carried out to improve air-conditioning efficiency. Increasing the efficiency of the condenser is directly connected to the power consumption of the compressor. This paper describes an experimental method of using an additional water-cooled condenser to reduce power consumption and decrease discharge pressure of the air-conditioning system. First, the principle of a combined cooling (water + air) method was evaluated theoretically. Next, experimental proof was conducted with the additional water-cooled condenser. The shape and structure is similar to the plate type of the transmission oil cooler used in a radiator. Through a number of tests, it was found that it is possible is to reduce power consumption of compressor by decreasing discharge pressure.

Many high risks of failure in developing and applying new technologies exist in the recent automotive industry because of big volume of selling cars in a global market. Several recalls cost companies more than $ 100 million per problem. New technologies always have uncertainty in performing intended functions at various given conditions despite the fact that engineers do their best to develop technologies to meet all the requirements. Uncertainty of new technologies put companies into danger of failing in their business. Therefore, many companies tend to take interest in reducing risks from the uncertainty in technologies, but the increasing complexity of modern automotive technologies make it difficult to develop complete technologies. A new engineering methodology called SPEED Engineering was introduced to reduce the risks of new technology applications and to facilitate engineers to conceive innovative ideas dominating the market in the future.

This report explains the basic theory of designing the accelerating durability test road and the role of each factors contributing to the test road surface profile. Also this road is designed by considering the charactors of vehicle suspension system and conditions of driving. In test road, the factors affecting to the vehicle structural durability are correlation among surface shape of road profile, frequency of vehicle suspension system,distribution of axle twist angle and vibration of road profile height. Road PSD magnitude and frequency delay is used to control these factors relation.

In this paper, a design procedure for the optimized light weight front cross member, which is a sub frame of the car chassis, without sacrificing basic functional requirements is presented. As the first step, optimal structural integrity was calculated and extracted using a CAE technique with the available volume constraint of the package layout. Quantitative design loads for the cross member was achieved by measurement. Dynamic load analysis using ADAMS was also performed to determine the loads. Later, these calculated loads were applied to the FEM stress analysis of the cross member. Furthermore, durability analysis was also performed using load profile database measured from ‘Hyundai Motor Co. Proving Ground’. Four constant amplitude durability tests and two static tests were performed on the cross member prototypes to confirm design reliability.

Currently, the interest in accelerated reliability testing (ART) of electric vehicles parts has been increasing. In particular, an electric motor and battery are vital components of battery powered electric vehicles. The electric motor has two major roles, to discharge or charge battery when it is driven or braking. For analyzing the exact behavior mechanism of electric motor and predicting lithium-ion battery cell degradation, new accelerated reliability testing technology is required. This paper describes the results of research and development in new approach to reliability testing for electric vehicles. The methodology to measure a precise motor output torque of the rotating rotor using telemetry system was provided. The electric energy quantities as well as the used quantities of the electric power were also analyzed. The results of research and development in new approach to reliability testing for electric vehicles were systematized and reflected in development.

Aluminum steering knuckles are widely employed for weight reduction and improvement of ride & handling performance. In this study, a high strength aluminum alloy for cast-forged knuckle was designed to achieve higher mechanical properties than those of the conventional foundry alloy. Using this alloy, high strength knuckles were manufactured and performed test of mechanical properties, suspension module strength and durability. The strength and the elongation of the developed knuckle were increased by 20% and 40%, respectively, as compared with the conventional alloy. Also this knuckle passed the static strength and durability test of the front suspension module.

In the present study, we developed a CVVL (Continuously Variable Valve Lift) engine. The CVVL mechanism is Hyundai Motor Company's own design, which is characterized by its compactness. The CVVL engine was developed without the increase of the engine height, thus the same hood line of the vehicle could be used with the base engine; the base engine does not adopt the CVVL technology, and it has the same engine specification other than valvetrain system. The CVVL mechanism was based on a six-linkage mechanism. Although the valvetrain friction of the CVVL engine of the six-linkage is higher than the base engine when operated with the same valve lift, it is in a competitive level compared to the other engines produced by HMC. The fuel consumption of the CVVL engine has been reduced by more than 5% compared to the base engine, and this is mainly thanks to the reduction of the pumping loss and friction.

Hyundai Motor Group launched a Continuously Variable Valve Lift (CVVL) engine in 2012. The engine is equipped with HMG's unique CVVL mechanism and is characterized by low fuel consumption, high performance and its responsiveness. The CVVL mechanism is based on a six-linkage mechanism and has advantages of compactness and durability. The engine is a 4 cylinder In-Line, 2.0L gasoline engine and is designed for a mid-sized passenger car. The engine increases fuel efficiency by 7.7% and the peak engine power by 4.2%. One of the most challenging issues in producing a CVVL engine is the valve lift deviations throughout the engine cylinders. The valve cap shim and set screw were designed to adjust the valve lift deviations. Cap shim thickness is chosen by measuring the valve top height, and shoe lift of the cam carrier assembly. The set screw is an auxiliary device to adjust the valve lift deviation.