Search Results

Road accidents and persons killed in India have been reported to the tune of 4,90,383 and 1,38,258 respectively during 2012. On National Highways (NHs), major share of accidents (about 29%) and number of persons killed (35.3%) are observed out of total accidents. National Highways in India constitute about 2% of total road network (92,851 km) in India, but carries about 40% of traffic. 46% (42,829 km) of NHs in India comprises of two-lane and about 19% (17239 km) of NHs are single or intermediate-lane. Road accidents being multi-disciplinary in nature involves attention of multiple departments such as Highways Authority, Police, Motor Vehicles, Automobile Manufacturers, NGOs, etc. Owing to spurt in growth of motor vehicle population in India, road accidents are not reduced significantly despite improvement in NHs (widening of carriageway and riding quality).

Severe problem of aerodynamic heating and drag force are inherent with any hypersonic space vehicle like space shuttle, missiles etc. For proper design of vehicle, the drag force measurement become very crucial. Ground based test facilities are employed for these estimates along with any suitable force balance as well as sensors. There are many sensors (Accelerometer, Strain gauge and Piezofilm) reported in the literature that is used for evaluating the actual aerodynamic forces over test model in high speed flow. As per previous study, the piezofilm also become an alternative sensor over the strain gauges due to its simple instrumentation. For current investigation, the piezofilm and strain gauge sensors have mounted on same stress force balance to evaluate the response time as well as accuracy of predicted force at the same instant. However, these force balance need to be calibrated for inverse prediction of the force from recorded responses.

Fatigue design has to account for the scatter of component geometry, material behavior and loading. Scatter of the first two variables is mainly due to manufacturing and material sourcing. Loading on the other hand depends decisively on operating conditions and customer usage. Loading is certainly most difficult to determine. Tests on proving ground or even long-term real time measurements are used to obtain actual load time histories. Because of the costs of measurements and safety measure, real-time measurements are used exceptionally to gain changes in the usage profile. In this paper, an attempt has been made to find the difference in the extrapolated data to the actual data. A comparison has been made between the actual road distance of 2000 km to the extrapolated data of 100 km, 500 km and 1000 km to 2000 km. The front Axle channel is taken for the study.

A novel Air-Alcohol INDUCTOR with an inherent flexibility to tailor the alcohol flow rate, has been developed for a multi-cylinder, variable-speed, vehicular Diesel engine to enable operation in the Alcohol-Diesel bi-fuel mode. Tests have been carried out on the dynamometer over the whole speed range of the engine. Also road tests have been carried out under constant vehicular speed conditions. Upto 48% Diesel substitution was achieved on road without reduction in thermal efficiency. Laboratory tests indicate lower exhaust temperatures and lower smoke intensities than in the diesel mode.

An analysis of the rollover propensity of a make of a TSR used extensively in S.E. Asia roads is presented using a 6-degree of freedom simulation. Verification of the model was against measured accelerations measured over speed breakers. Rollover stability was analyzed through simulating Increasing Steer, NHTSA J Turn, and Road Edge Recovery maneuvers.

In commercial vehicles, exhaust system is normally mounted on frame side members (FSM) using hanger brackets. These exhaust system hanger brackets are tested either as part of full vehicle durability testing or as a subsystem in a rig testing. During initial phases of product development cycle, the hanger brackets are validated for their durability in rig level testing using time domain signals acquired from mule vehicle. These signals are then used in uni-axial, bi-axial or tri-axial rig facilities based on their severity and the availability of test rigs. This paper depicts the simulation method employed to replicate the bi-directional rig testing through modal transient analysis. Finite Element Method (FEM) is applied for numerical analysis of exhaust system assembly using MSC/Nastran software with the inclusion of rubber isolator modeling, meshing guidelines etc. Finite Element Analysis (FEA) results are in good agreement with rig level test results.

Gasoline direct injection (GDI) technology is already in use in four wheeler applications owing to the additional benefits in terms of better combustion and fuel economy. The air-assisted in-cylinder injection is the emerging technology for gasoline engines which works with low pressure injection systems unlike gasoline direct injection (GDI) system. GDI systems use high pressure fuel injection, which provides better combustion and reduced fuel consumption. It envisages small droplet size and low penetration rate which will reduce wall wetting and hydrocarbon emissions. This study is concerned with a CFD analysis of an air-assisted injection system to evaluate mixture spray characteristics. For the analysis, the air injector fitted onto a constant volume chamber (CVC) maintained at uniform pressure is considered. The analysis is carried out for various CVC pressures, mixture injection durations and fuel quantities so as to understand the effect on mixture spray characteristics.