Search Results

In the development of HC traps (HCT) for reducing vehicle cold start hydrocarbon (HC)/nitrogen oxide (NOx) emissions, zeolite-based adsorbent materials were studied as key components for the capture and release of the main gasoline-type HC/NOx species in the vehicle exhaust gas. Typical zeolite materials capture and release certain HC and NOx species at low temperatures (<200°C), which is lower than the light-off temperature of a typical three-way catalyst (TWC) (≥250°C). Therefore, a zeolite alone is not effective in enhancing cold start HC/NOx emission control. We have found that a small amount of Pd (<0.5 wt%) dispersed in the zeolite (i.e., BEA) can significantly increase the conversion efficiency of certain HC/NOx species by increasing their release temperature. Pd was also found to modify the adsorption process from pure physisorption to chemisorption and may have played a role in the transformation of the adsorbed HCs to higher molecular weight species.

Engine and flow reactor experiments were conducted to determine the impact of biodiesel relative to ultra-low-sulfur diesel (ULSD) on inhibition of the selective catalytic reduction (SCR) reaction over an Fe-zeolite catalyst. Fe-zeolite SCR catalysts have the ability to adsorb and store unburned hydrocarbons (HC) at temperatures below 300°C. These stored HCs inhibit or block NOx-ammonia reaction sites at low temperatures. Although biodiesel is not a hydrocarbon, similar effects are anticipated for unburned biodiesel and its organic combustion products. Flow reactor experiments indicate that in the absence of exposure to HC or B100, NOx conversion begins at between 100° and 200°C. When exposure to unburned fuel occurs at higher temperatures (250°-400°C), the catalyst is able to adsorb a greater mass of biodiesel than of ULSD. Experiments show that when the catalyst is masked with ULSD, NOx conversion is inhibited until it is heated to 400°C.

Lean NOx Traps are used to treat the NOx emissions from lean-burn engines by storing the NOx under lean conditions and reducing the NOx during periodic rich excursions. However, sulfur poisons the adsorption sites of the traps. The sulfur can be removed from the NOx trap by operating rich at high temperatures for several minutes. This results in the release of some SO2 but also large quantities of H2S, which is a source of customer dissatisfaction that must be reduced or eliminated. This paper describes the use of a nickel-containing catalyst and air/fuel control to maximize the release of SO2 and minimize the emissions of H2S during the desulfation of a lean NOx trap. We present laboratory and vehicle data with a nickel-containing catalyst located downstream of a lean NOx trap during desulfations of the trap. The nickel effectively reduced the emissions of H2S during the desulfation while improving the robustness to fluctuations in the air/fuel control.

Selective Catalytic Reduction (SCR) catalysts have been designed to reduce NOx with the assistance of an ammonia-based reductant. Diesel Particulate Filters (DPF) have been designed to trap and eventually oxidize particulate matter (PM). Combining the SCR function within the wall of a high porosity particulate filter substrate has the potential to reduce the overall complexity of the aftertreatment system while maintaining the required NOx and PM performance. The concept, termed Selective Catalytic Reduction Filter (SCRF) was studied using a synthetic gas bench to determine the NOx conversion robustness from soot, coke, and hydrocarbon deposition. Soot deposition, coke derived from propylene exposure, and coke derived from diesel fuel exposure negatively affected the NOx conversion. The type of soot and/or coke responsible for the inhibited NOx conversion did not contribute to the SCRF backpressure.

The effects of PGM zoning and washcoat staging have been investigated as a means to lower the cost and simultaneously improve the performance of a lean NOx trap system. It is shown that reverse PGM zoning can be used to reduce the cost of the LNT while essentially maintaining the NOx performance of a similarly-sized trap with a uniformly high PGM loading. In addition, the effective temperature window of the trap can be expanded by staging different NOx trap formulations that are optimized for different temperature ranges. Alternatively, LNT washcoat staging can be used to improve the hydrocarbon conversion of the trap while maintaining good NOx performance. Laboratory data and vehicle data are presented for several NOx trap system combinations that demonstrate the improved performance that can be obtained from a combination of reverse PGM zoning and washcoat staging.

A study was performed on a lean NOx trap in which the loading of a ceria-containing mixed oxide in the washcoat was varied. After a mild stabilization of the traps, the time required to purge the NOx trap generally increased with increasing amount of mixed oxide. The purge NOx release also increased with increasing mixed oxide level but was greatly diminished after thermal aging. The sulfur tolerance of the NOx trap improved as the mixed oxide content was increased from 0% to 37%. The sample with 0% mixed oxide was more difficult to desulfate than the other samples due to poor water-gas-shift capability. After thermal aging, the NOx reduction efficiency on a 60 second lean/5 second rich cycle was highest for the samples with 0% to 37% mixed oxide at evaluation temperatures of 400°C to 500°C.