Search Results

The aim of this research was to find vehicle characteristics including stiffness that is effective for compatibility performance. Compatibility is said to be affected by three factors: vehicle mass, geometry and stiffness (1, 2). Of these factors, stiffness has more flexibility at the design stage than vehicle mass and geometry which are limited by the vehicle application. However, the stiffness is assumed to have a conflict issue between the self-protection and the partner-protection (3). In this research, it was analyzed comprehensively how some defined factors such as stiffness, mass, crash stroke and other vehicle characteristics indices relate to each occupant injury rate of the case and its partner vehicle in the real-world accidents. Both “front-to-front” and “front-to-side” crash occupants were covered.

To reduce real world fatal/serious/minor injuries, factors causing such injuries should be investigated in depth from wider perspectives. The aim of this paper is to clarify the factors based on Japanese accident database compiled by ITARDA (Institute for Traffic Accident Research and Data Analysis). ITARDA database has data for injury rates, seatbelt use rate of driver and age of driver involved in crashes, etc. by vehicle model. As a result of an elaborate statistical analysis, the most influential and essential factors on all injuries including fatality were quantitatively found to be seatbelt use rate and vehicle weight. The increase by 1% in seatbelt use rate makes injury rate decrease by 7%. The influence of vehicle weight is 1.7 times higher than seatbelt use rate. Multiple regression analysis on these two parameters was also conducted. The present analysis successfully predicted all injury rates by model per 10,000 units.

This paper clarifies aggressivity reduction approach for MPV, Multi-Purpose Vehicles, derived from large passenger vehicles toward small passenger vehicles. The effects of aggressivity-reducing approach were measured through full-frontal rigid barrier crash simulations with TRL aluminum honeycomb by Finite Element Method. The front-end structures of large vehicles studied in this paper based on this aggressivity reduction approach show good front-end homogeneity and low average height of force. The structures were also found to effectively reduce aggressivity toward small vehicles by car-to-car simulation. However, there are some cases where the effect was influenced by overlap ratios. From this result, overlap ratio is considered to be one of the important factors to improve compatibility performance.

Driver fatality rate of a passenger vehicle is considerably high when struck on the side by an LTV (light truck and van). Aggressivity of LTVs, particularly in side crashes, needs to be reduced to improve this incompatible situation. Crash energy absorption share of a passenger car struck on the side by an LTV was measured through component tests. As a result, B-pillar of the struck passenger car was found to receive most of the crash energy intensively. This intensive energy triggered large B-pillar deformation. Computer simulation proved that B-pillar deformation was closely related to occupant injury. The key to mitigate the injury of side-struck car occupant, therefore, is to disperse crash energy to other structural parts than B-pillar. Front-end structures of LTVs that realize crash energy dispersion were designed and examined. The structures include (a) optimization of the vehicle height, and (b) adoption of a forward-extended sub-frame.

With an aim to improve compatibility performance, vehicle-to-vehicle frontal impact simulations have been conducted between large car and small car. Focusing on sub-frame structure that disperses applied force with multiple load paths, a large saloon car with sub-frame was selected and three different front structures were studied: original, forward-extended sub-frame, and original with 25%-stiffness reduced structures. The types of collision contained four different crash modes in a combination of lateral overlap rate difference and side member height difference. As a result, it was found that the front structure with forward-extended sub-frame improved aggressivity by preventing override effect through structural interaction enhancement. Height of Force (HOF) was also improved.

Continuous improvement of side airbag safety performance is an important step because it is associated with many public domain tests and regulations. Thus, occupant restraint with a side airbag is critical and it is necessary to develop tools that can be utilized to help in design of side airbags. Though many papers on side impact safety have been published, only a few papers are related to MADYMO simulations of side airbags. This paper describes an improved injury prediction and optimization approach using a MADYMO model for side impact. This model consists of 3 parts: dummy, trim and airbag in FEM. In this study, a side impact with a ES-2, EuroSID-2, was simulated in MADYMO as follows: First, component tests were conducted for trim and airbag respectively to establish correlation. Second, these component models were then integrated into a MADYMO model, which has high correlation with a crash simulator that is capable of replicating physical vehicle tests.

Of the injuries sustained by belted rear occupants in a frontal collision event in Japan, the neck and the head are the regions of the body most likely to be injured, while children and female occupants are accounting for the highest rate of injuries. For the purpose of reducing rear seat occupant injuries, the occurrence mechanism of neck and head injuries is clarified by sled tests with the current rear seat belt system. When a high load is applied to the occupant via the seat belt, the occupant experiences sudden deceleration of the chest, resulting in a great relative velocity difference between the head and the chest. This causes injury to the occupant's neck and head. To reduce occupant injuries, therefore, it is important to minimize the relative velocity difference by control of belt load.

Seat lumbar support is thought to be essential for seating comfort as it plays important role in the driver's fatigue during long term driving. We tried to evaluate the lumbar support performance objectively with Seat Pressure Distribution. First, the tolerance in the measurement was eliminated by application of ASPECT manikin that reproduced a human seating torso posture [1, 2]. Second, an analysis method to visualize the seat support balance on the human back was developed. Third, a hypothesis for the optimal support balance to minimize the fatigue was proposed according to the fatigue growing mechanisms. Examining the deviation of each seat result from the optimal support, the performances were quantitatively evaluated. In addition to that, the effect of the lumbar support adjuster was taken into consideration to predict the market evaluation more precisely.

Development of anti-whiplash technology is one of the hottest issues in the automotive safety field because of the frequent occurrence of rear impact accidents. We analyzed the whiplash mechanism and conducted a study to seek the optimized seat characteristics with BioRID II and MADYMO simulations. A parameter study was made to construct a conceptual theory to decrease NIC, Neck Injury Criteria, with the MADYMO model. As a result of the study, head restraint position and seatback stiffness were found to affect dummy movement and injury values. Applying the NIC mechanism and the influential parameters to the MADYMO model, the optimized seat characteristics for whiplash prevention were obtained.

The present study had two aims: (1) to develop a model which reproduced the dummy lower leg kinematics observed in a high-speed test, and (2) to develop a methodology to assess various theoretical design parameters of a heel foam pad to reduce the risk of the lower extremity injuries. To address the first aim, a MADYMO sled simulation model was developed. The interior parts were represented mainly with finite element (FE) models, with intent to capture deformations and the reaction force directions. Moreover, the occupant responses were estimated from the refined version of the dummy model (i.e., the Hybrid III model; Q dummy model). The model was acceptably correlated to experiments. To address the second aim, the model was simplified for subsequent optimization of the heel foam pad.

In order to secure effective occupant protection at vehicle collisions, it is necessary to conduct close examination into vehicle crash characteristics as well as interior parts, etc. This paper analyzes the behavior of a HYBRID III dummy restrained by three point seatbelt using MVMA2D computer simulation program at a 35 mph vehicle frontal barrier crash. As a result, it is found for good agreement between experiment and simulation that the exact input data of successive toeboard intrusion play an important role. As for the parametric study on vehicle crashworthiness, the authors propose the convenient method to represent the actual crash pulse by two simplified trapezoids. Then using these trapezoids, the parametric study clarifies the influence of vehicle deformation characteristics as well as the interior parts on dummy injury.