Search Results

Future fuel economy targets represent a significant challenge to the automotive industry. While a range of technologies are in research and development to address this challenge, they all bring additional cost and complexity to future products. The most cost effective solutions are likely to be combinations of technologies that in isolation might have limited advantages but in a systems approach can offer complementary benefits. This presentation describes work carried out at Ricardo to explore Intelligent Electrification and the use of Stratified Charge Lean Combustion in a spark ignition engine. This includes a next generation Spray Guided Direct Injection SI engine combustion system operating robustly with highly stratified dilute mixtures and capable of close to 40% thermal efficiency with very low engine-out NOx emissions.

An automatic matching method for engine control parameters is described which can aid efficient development of new engine control systems. In a spark-ignition engine, fuel is fed to a cylinder in proportion to the air mass induced in the cylinder. Air flow meter characteristics and fuel injector characteristics govern fuel control. The control parameters in the electronic controller should be tuned to the physical characteristics of the air flow meter and the fuel injectors during driving. Conventional development of the engine control system requires a lot of experiments for control parameter matching. The new matching method utilizes the deviation of feedback coefficients for stoichiometric combustion. The feedback coefficient reflects errors in control parameters of the air flow meter and fuel injectors. The relationship between the feedback coefficients and control parameters has been derived to provide a way to tune control parameters to their physical characteristics.

Charge motion is known to accelerate and stabilize combustion through its influence on turbulence intensity and flame propagation. The present work investigates the effect of charge motion generated by intake runner blockages on combustion characteristics and emissions under part-load conditions in SI engines. Firing experiments have been conducted on a DaimlerChrysler (DC) 2.4L 4-valve I4 engine, with spark range extending around the Maximum Brake Torque (MBT) timing. Three blockages with 20% open area are compared to the fully open baseline case under two operating conditions: 2.41 bar brake mean effective pressure (bmep) at 1600 rpm, and 0.78 bar bmep at 1200 rpm. The blocked areas are shaped to create different levels of swirl, tumble, and cross-tumble. Crank-angle resolved pressures have been acquired, including cylinders 1 and 4, intake runners 1 and 4 upstream and downstream of the blockage, and exhaust runners 1 and 4.

A new integrated control system has been developed for controlling an SI engine and a CVT proactively so as to obtain the demanded drive torque most efficiently. Taking into account ease of calibration, a control system configuration has been achieved that determines the CVT ratio from the target drive torque and vehicle speed, based on the steady-state relationship between the demanded drive torque and the vehicle speed, gear ratio, engine torque and fuel economy. An analysis was made of drive torque characteristics while the ratio was changing under transient conditions. The results showed that using engine torque to compensate for the ratio change response lag and inertia torque, which is proportional to the differential of the gear ratio, is effective in improving drive torque responsiveness.

Coherent anti-Stokes Raman spectroscopy (CARS) temperature measurements were performed in the unburned gas in a spark ignition engine. First, as the residual gas mass fraction is one of the factor that is known to cause to autoignition, the effect of the residual gas mass fraction on the unburned gas temperature is estimated. In order to control the residual gas mass fraction, a skip fired cycle method was used., and the single cylinder test engine used in this study was fueled with gasoline (89.9 RON). The residual gas causes the unburned gas temperature to rise by approximately 55 K and it also produces a large temperature variation on the order of ±20 K when expressed as a standard deviation. Second, the unburned gas temperature of the single cylinder test engine and the 4 valve production engine was measured under steady-state engine operation in order to compare the residual gas mass fraction of the test engine with that of the production engine.

Heavy fuel engines have typically been limited to large, heavy compression ignition engines. However, with the push by the US military to use a common fuel (JP5/JP8/diesel) there is a need to develop small, lightweight, high performance engines that are also capable of operating on heavy fuel. Recent advancements in air assisted direct injection technologies have improved fuel atomization to the level necessary to overcome the poor physical properties of heavy fuel. This has permitted the operation of small two-stroke engines which retain the advantage of a lightweight design with high power output. This paper discusses the process of benchmarking a two-stroke heavy fuel spark ignited engine with an integrated air-assist direct injection system. The setup and commissioning phases of the testing are outlined, including specific techniques for quantifying scavenging, burn rate, and heat release characteristics with the objective of validating a 1-D performance simulation model.

Cam-phasing is increasingly considered as a feasible Variable Valve Timing (VVT) technology for production engines. Additional independent control variables in a dual-independent VVT engine increase the complexity of the system, and achieving its full benefit depends critically on devising an optimum control strategy. A traditional approach relying on hardware experiments to generate set-point maps for all independent control variables leads to an exponential increase in the number of required tests and prohibitive cost. Instead, this work formulates the task of defining actuator set-points as an optimization problem. In our previous study, an optimization framework was developed and demonstrated with the objective of maximizing torque at full load. This study extends the technique and uses the optimization framework to minimize fuel consumption of a VVT engine at part load.

This paper presents a study of mixture formation in the combustion chamber of a direct-injection SI engine. In-cylinder flow measurement was conducted using laser Doppler velocimetry (LDV) and particle image velocimetry (PIV), and visualization of fuel vapor behavior was done using laser-induced fluorescence (LIF). Further, fast response flame ionization detector (FID) was used to measure the hydrocarbon (HC) concentrations in the vicinity of the spark plug. Thereby mixture concentrations in the vicinity of the spark plug, within the mixture distribution observed using LIF, were quantified. Results revealed that an upward flow forms near the center of the cylinder in the latter half of the compression stroke and goes from the piston crown toward the cylinder head. This upward flow is caused by the synergistic effect of the swirl motion generated in the cylinder and the cylindrical bowl provided in the piston crown eccentrically to the central axis of the cylinder.

This study attempts to develop a correlation between an airflow motion number, combustion burn rates, and initial flame kernel development. To accomplish this task, several motion plates were evaluated on a flowbench in order to calculate a motion number that would represent the dynamic motion in the combustion chamber. Afterwards, the plates were tested on a spark ignited engine at several part throttle conditions while gathering cylinder pressure measurements. These cylinder pressure measurements would then yield the combustion burn rates for each plate. In addition to the combustion measurements, the flame kernel growth, velocity and direction of the flame kernel were measured using an AVL Visio-flame. Finally, the data was evaluated and an attempt to correlate the motion number of the plates to the different measurements for describing combustion was made.

Simultaneous crank-angle-resolved measurements of gasoline vapor concentration, gas temperature, and liquid fuel droplet scattering were made with three-color infrared absorption in a direct-injection spark-ignition engine with premium gasoline. The infrared light was coupled into and out of the cylinder using fiber optics incorporated into a modified spark plug, allowing measurement at a location adjacent to the spark plug electrode. Two mid-infrared (mid-IR) laser wavelengths were simultaneously produced by difference-frequency-generation in periodically poled lithium niobate (PPLN) using one signal and two pump lasers operating in the near-infrared (near-IR). A portion of the near-IR signal laser residual provided a simultaneous third, non-resonant, wavelength for liquid droplet detection. This non-resonant signal was used to subtract the influence of droplet scattering from the resonant mid-IR signals to obtain vapor absorption signals in the presence of droplet extinction.

A transient knock prediction technique has been developed by coupling a zero-dimensional knocking simulation with chemical kinetics and a one-dimensional gas exchange engine model to study the occurrence of transient knock in SI engines. A mixed chemical reaction mechanism of the primary reference fuels was implemented in the two-zone combustion chamber model as the auto-ignition model of the end-gas. An empirical correlation between end-gas auto-ignition and knock intensity obtained through intensive analysis of experimental data has been applied to the knocking simulation with the aim of obtaining better prediction accuracy. The results of calculations made under various engine operating parameters show good agreement with experimental data for trace knock sensitivity to spark advance.

To improve the fuel economy, we developed a turbo-charged spark ignition engine combined with a low pressure loop EGR system. A negative pressure control valve has been applied to achieve high EGR ratio in wide engine operation condition. In this paper, a new developed model-based control system for low pressure loop EGR with a negative pressure control valve will be described.

The Ethanol-Boosted Direct Injection (EBDI) demonstrator engine is a collaborative project led by Ricardo targeted at reducing the fuel consumption of a spark-ignited engine. This paper describes the design challenges to upgrade an existing engine architecture and the synergistic use of a combination of technologies that allows a significant reduction in fuel consumption and CO₂ emissions. Features include an extremely reduced displacement for the target vehicle, 180 bar cylinder pressure capability, cooled exhaust gas recirculation, advanced boosting concepts and direct injection. Precise harmonization of these individual technologies and control algorithms provide optimized operation on gasoline of varying octane and ethanol content.

In spark-ignition engine pumping loss increases and fuel economy decreases during partial load operation. Methods to reduce this pumping loss by controlling the intake-valve closing timing are currently under study. The authors, also, have confirmed that pumping loss can be reduced by controlling the amount of intake air-fuel mixture through making changes in the in Cake-valve closing timing. However, when pumping loss was reduced by controlling intake-valve closing timing, an improvement in fuel economy equivalent to the reduction in pumping loss was not obtained. In this study, it was found that the major contributing factor to this phenomenon was the deterioration of the combustion, namely, increase in combustion duration and in combustion fluctuation.

Due to the recent drive to reduce CO₂ emissions, the turbocharged direct injection spark ignition (turbo DISI) gasoline engine has become increasingly popular. In addition, future turbo DISI engines could incorporate a form of charge dilution (e.g., lean operation or external EGR) to further increase fuel efficiency. Thus, the conditions experienced by the fuel before and during combustion are and will continue to be different from those experienced in naturally aspirated SI engines. This work investigates the effects of fuel properties on a modern and prototype turbo DISI engine, with particular focus on the octane appetite: How relevant are RON and MON in predicting a fuel's anti-knock performance in these modern/future engines? It is found that fuels with high RON and low MON values perform the best, suggesting the current MON requirements in fuel specifications could actually be detrimental.

Earlier work has demonstrated that exhaust gas recirculation (EGR) decreases peak combustion temperature and thus reduces the concentration of nitrogen oxides (NOx) in spark ignition engine exhaust. The present authors hypothesized that NOx formation is primarily affected by the heat capacity of the combustion gases and recycled exhaust. The hypothesis was tested in an experimental program involving the admission of inert gases such as He, Ar, H2, and CO2, and water in place of EGR. In addition to confirming the validity of the original hypothesis, the test data also indicated that engine output and efficiency were significantly affected by the heat capacity of the combustion gases. The authors conclude that EGR functions by increasing the heat capacity of the working fluid, and demonstrates that the correlative changes in NOx and engine performance can be predicted from heat capacity considerations.

In order to study the potentiality of the modification of the combustion rate for NOx formation control in the spark ignition (SI) engine, the authors first developed a new mathematical model by assuming the stepped gas temperature gradient in the cylinder. The predicted results from this new mathematical model show good coincidence with the experimental data. Second, the authors discuss the effects of the modification of the combustion rate on NOx formation using the new mathematical model. It was concluded that NOx formation in the premixed SI engine would be essentially determined by the specific fuel consumption only, regardless of any modification of the engine combustion rate.

An investigation has been done on the relationship between spark ignition characteristics and combustion stability in a gasoline engine. The spark discharge parameters examined were the spark current, energy, and duration. It has been found that lengthening the spark discharge duration is particularly effective in achieving stabilized combustion. A longer spark duration provides a continued supply of electric energy as kinetic energy to the mixture around the spark gap. The analytical results of a constant volume combustion chamber test verify that a longer spark duration promotes flame initiation and makes reliable flame propagation possible. The length of the spark duration is regarded as the period from ignition to the onset of combustion pressure rise. The results of a combustion pressure analysis reveal that the spark duration must be longer than the heat release delay.

An accurate air flow rate model is critical for high-quality air-fuel ratio control in Spark-Ignition engines using a Three-Way-Catalyst. Emerging Variable Valve Timing technology complicates cylinder air charge estimation by increasing the number of independent variables. In our previous study (SAE 2004-01-3054), an Artificial Neural Network (ANN) has been used successfully to represent the air flow rate as a function of four independent variables: intake camshaft position, exhaust camshaft position, engine speed and intake manifold pressure. However, in more general terms the air flow rate also depends on ambient temperature and pressure, the latter being largely a function of altitude. With arbitrary cam phasing combinations, the ambient pressure effects in particular can be very complex. In this study, we propose using a separate neural network to compensate the effects of altitude on the air flow rate.

Due to the rising costs of fuel and increasingly stringent regulations, auto makers are in need of technology to enable more fuel-efficient powertrain technologies to be introduced to the marketplace. Such powertrains must not sacrifice performance, safety or driver comfort. Today's engine and powertrain manufacturers must, therefore, do more with less by achieving acceptable vehicle performance while reducing fuel consumption. One effective method to achieve this is the extreme downsizing of current direct injection spark ignited (DISI) engines through the use of high levels of boosting and cooled exhaust gas recirculation (EGR). Key challenges to highly downsized gasoline engines are retarded combustion to prevent engine knocking and the necessity to operate at air/fuel ratios that are significantly richer than the stoichiometric ratio.