Search Results

An analytical model based on “vortex sound” theory was investigated for predicting the frequency, the relative magnitude, the onset, and the offset of self-sustained interior pressure fluctuations inside a vehicle with an open sunroof. The “buffeting” phenomenon was found to be caused by the flow-excited resonance of the cavity. The model was applied to investigate the optimal sunroof length and width for a mid-size sedan. The input parameters are the cavity volume, the orifice dimensions, the flow velocity, and one coefficient characterizing vortex diffusion. The analytical predictions were compared with experimental results obtained for a system which geometry approximated the one-fifth scale model of a typical vehicle passenger compartment with a rectangular, open sunroof. Predicted and observed frequencies and relative interior pressure levels were in good agreement around the “critical” velocity, at which the cavity response is near resonance.

Original equipment manufacturers and their customers are demanding more efficient, lighter, smaller, safer, and smarter systems across the entire product line. In the realm of automotive, agricultural, construction, and earth-moving equipment industries, an additional highly desired feature that has been steadily trending is the capability to offer remote and autonomous operation. With the previous requirements in mind, the authors have proposed and validated a new electrohydraulic steering technology that offers energy efficiency improvement, increased productivity, enhanced safety, and adaptability to operating conditions. In this paper, the authors investigate the new steering technology's capacity to support remote operation and demonstrate it on a compact wheel loader, which can be remotely controlled without an operator present behind the steering wheel. This result establishes the new steer-by-wire technology's capability to enable full autonomous operation as well.

A feedback controller bas been developed using robust control techniques to control the sound radiated from turbulent flow driven plates. The control design methodology uses frequency domain loop shaping techniques. System uncertainty, sound pressure level reductions, and actuator constraints are included in the design process. For the wind noise problem, weighting factors have been included to distinguish between the importance of modes that radiate sound and those that do not radiate. The wind noise controller has been implemented in the quiet wind tunnel facility at the Ray W. Herrick Laboratories at Purdue University. A multiple-input, multiple-output controller using accelerometer feedback and shaker control was able to achieve control up to 1000 Hz. Sound pressure level reductions of as much as 15 dB were achieved at the frequencies of the plates modes. Overall reductions over the 100-1000 Hz band were approximately 5 dB.

NO and soot emissions from Diesel engines are dependent on several parameters related to the engine design and operating conditions. Multidimensional models are increasingly employed to study the effect of these parameters. In this paper, a multidimensional model for flows, sprays and combustion in engines is employed to study the dependence of NO and soot formation and oxidation on injection timing, injection pressure, chamber temperature, EGR and ignition delay, and compare the computed trends with those observed in experimental studies reported in the literature. Computations are carried out in a typical heavy-duty Diesel engine and additional computations in a constant volume chamber are used to clarify the engine results when appropriate. For several parametric changes, the experimentally observed trends are reproduced. However, several limitations are identified. The structure of the computed combusting jet has differences with those suggested from recent experiments.

The renewed interest in electric and hybrid-electric vehicles has been prompted by the drastic rise in oil prices in 2008 and launch of new initiatives by the Federal Government. One of the key issues is to promote the incorporation of electric drivetrain in vehicles at all levels and particularly with emphasis on educational activities to prepare the workforce needed for the near future. Purdue University has been conducting a Grand Prix for over 50 years with Gas-powered Karts. In April 2010, an annual event was initiated to hold an EV Grand Prix where 17 EV Karts participated in the competition. Four of the participating teams comprised of Purdue students in a new graduate course for EV design and fabrication. Using the basic framework of the gas-powered Kart, an electric version was developed as a part of this course. Other participants were also provided with the guidelines and design parameters developed for the course and competition.

Energy budgets for future Controlled Ecological Life-Support Systems (CELSS) must balance not only with respect to primary productivity (i.e., photosynthesis) vs. utilization steps (human maintenance plus preparative and recycling processes), but also with respect to necessary and desired nonlife-support activities of crews (e.g., exploration, research). Present objectives of the NSCORT program at Purdue University include identification of critical paths for biomass conversion to desired forms with energetics and rate-constant properties that are compatible with life-support sustainability within a CELSS. Physico-chemical recycling systems working in conjunction with bioregenerative ones likely will be required to keep time constants of critical processes within reasonable limits.

The feasibility of controlling the threshing cylinder of a conventional corn combine with electro hydraulic elements controlled by a digital computer was concluded. The laboratory experiments attained the performance index established after consultation with manufacturers and farmers

A unique concept for a multi-body test rig enabling the simulation of longitudinal, steering and vertical dynamics was developed at the Institute for Mechatronic Systems (IMS) at TU Darmstadt. A prototype of this IMS test rig is currently being built. In conjunction with the IMS test rig, the Vehicle Terrain Performance Laboratory (VTPL) at Virginia Tech further developed a full car, seven degree of freedom (7 DOF) simulation model capable of accurately reproducing measured displacement, pitch, and roll of the vehicle body due to terrain excitation. The results of the 7 DOF car model were used as the reference input to the multi-body IMS test rig model. The goal of the IMS/VTPL joint effort was to determine whether or not a controller for the IMS test rig vertical actuator could accurately reproduce wheel displacements due to different measured terrain constraints.

Grazing flows over open windows or sunroofs may result in “flow buffeting,” i.e. self-sustained flow oscillations at the Helmholtz acoustic resonance frequency of the vehicle. The associated pressure fluctuations may cause passenger fatigue and discomfort. Many solutions have been proposed to solve this problem, including for example leading edge spoilers, trailing edge deflectors, and leading edge flow diffusers. Most of these control devices are “passive” i.e. they do not involve dynamic control systems. Active control methods, which do require dynamic controls, have been implemented with success for different cases of flow instabilities. Previous investigations of the control of flow-excited cavity resonance have used mainly one or more loudspeakers located within the cavity wall. In this study, oscillated spoilers hinged near the leading edge of the cavity orifice were used. Experiments were performed using a cavity installed within the test section wall of a wind tunnel.

The Porous Ceramic Tube - Nutrient Delivery System (PCT-NDS) offers means to control water availability to plants under non-standard gravities. It is hypothesized that control can be obtained by applying suction pressure within the ceramic tubes. The research objectives include verifying the presented control equation for the PCT-NDS under micro-(less than 1 g) and hyper- (greater than 1 g) gravities. Experiments were conducted on a KC-135 subjecting the system to near-zero to 2 g's and to sustained hyper-gravities upto 10 g's using a centrifuge. Results indicated that the water availability can be controlled through applied suction pressure.

The object of the work reported here was to relate the acoustic intensity level measured near the contact patch of a driven tire on a passenger vehicle with the passby noise levels measured at a sideline microphone during coast and cruise conditions. Based on those measurements it was then possible to estimate the tire noise contribution to the passby level measured when the vehicle under test was accelerating. As part of this testing program, data was collected using five vehicles at fourteen passby sites in the United States: in excess of 800 data sets were obtained.

Farmers are a small group, mostly college educated who run multi-million dollar yearly operations. Recent favorable economics has allowed this sector to look at new technology and determine the best way to invest in it. New considerations in the last few years have led to minimum/alternative tillage and planting, site specific farming decisions and small technology groups of farmers. The authors have put together their thoughts and wants which should be evaluated by future suppliers of technology and farm machinery.

One of the most common barriers to the timely disposition of maintenance discrepancies involves communication difficulties between pilots and technicians. These barriers occur at virtually every operational level of the aviation industry from general aviation to airline. Well intentioned yet incomplete or misdirected communication often results not only in frustration, excessive down time, and recurrence of the problem, but also fosters unhealthy (and inaccurate) stereotypical notions about the overall competence of each group. This paper focuses on a two-phase study designed to identify which human factors impede pilot - mechanic communication and which factors promote pilot - mechanic communication. The project was coordinated by a joint faculty - student research team from the Department of Aviation Technology at Purdue University.

Two structure-borne and two airborne paths were measured on 99 “identical” Isuzu RODEOs and 57 “identical” Isuzu pickup trucks. Significant effort was made to control measurement variability but not environmental (climate) variations. A record was kept of the tests of a reference vehicle over the variation of environmental factors. The frequency response functions (FRFs) of the reference vehicle varied by approximately 2-4 dB over the frequency range 0-500 Hz for the structure-borne paths and over 0-1000 Hz for the airborne paths due to measurement and environmental variations. The FRFs of the fleet varied by as much as 5-10 dB over the same frequency range. In this paper, the vehicle tests are described. The reference and the fleet data are shown in raw form. Reduced data and implications of the results are also discussed.

Purdue undergraduate Agricultural Engineers have high employment rates at graduation, during a period of very low demand for engineers. The reason includes several unique faculty efforts to place students which enhance their current work ethic and topical engineering courses.

A noise source identification technique for the analysis of thermal systems is presented. The proposed method uses transient spectral sound data to assist in determining the source of sound radiation by tracking the variation of the frequency of tones during transient thermal loading (i.e., thermal system warm-up). By considering the temperature dependence of the modulus of elasticity (Young's modulus) it can be shown that structure related tones will decrease in frequency during warm-up. Tones due to propagation of sound in many fluids (i.e., gases and water) will increase in frequency during warm-up due to the temperature dependence of the speed of sound. The analysis method is demonstrated by identifying the source of several noise tones for a pulse combustion furnace.

Numerical simulations are performed to investigate noise generated by flow in automotive HVAC ducts. A hybrid computational method for analyzing flow noise is applied: Large Eddy Simulation (LES) for predicting flow fields and Multi-domain boundary element method for predicting acoustic propagation. LES gives time-resolved solutions of flow velocity and pressure fields. By applying the acoustic analogy theory, the unsteady flow parameters are translated into sound source in evaluating the acoustic propagation. The computational result shows the noise caused by the HVAC ducts is strong. The noise is of broadband with a peak value at 370Hz. A major contribution of the noise generation is from the center ducts. Two design modifications of the center ducts are explored to regulate the flow structures with the ducts for reducing noise generation. Test results demonstrate the effectiveness of the modifications.

Modern diesel engines typically utilize pulse-turbocharging where an increase in exhaust gas transport efficiency is achieved at the expense of creating a highly unsteady flow through the turbine which may have a detrimental effect on turbine performance. As the turbocharger plays a major role in the performance and emissions of the engine system, the characterization of on-engine turbocharger aerodynamics is critical. Thus, this paper is directed at the investigation of the turbocharger turbine volute inlet flowfield on an in-line, six cylinder, diesel engine. Specifically, Particle Image Velocimetry (PIV), a quantitative non-intrusive whole flowfield measurement technique, is used to perform a detailed study of the on-engine pulsating flowfield at the volute inlet of the twin-entry turbocharger turbine.

“Personal and Charitable Planning Under Tax Relief 2001” addresses the need for taxpayers and estate and financial planners to reconsider their financial, retirement and estate plans in the coming years. Recent extensive changes in the tax code require careful consideration during each of the next several years in order to balance tax savings while maintaining personal, financial and charitable objectives. The purpose of this paper is to provide a brief view of some of the various provisions of the Act.

The flow-induced pressure fluctuations in a door gap cavity model were investigated experimentally using a quiet wind tunnel facility. The cavity cross-section dimensions were typical of road vehicle door cavities, but the span was only 25 cm. One cavity wall included a primary bulb rubber seal. A microphone array was used to measure the cavity pressure field over a range of flow velocities and cavity configurations. It was found that the primary excitation mechanism was an “edge tone” phenomenon. Cavity resonance caused amplification around discrete frequencies, but did not cause the flow disturbances to lock-on. Possible fluid-elastic coupling related to the presence of a compliant wall was not significant. A linear spectral decomposition method was then used to characterize the cavity pressure in the frequency domain, as the product of a source spectral distribution function and an acoustic frequency response function.