Search Results

The combustion system developed for the General Motors GT-309 regenerative gas turbine is used to illustrate pertinent structural, performance, and exhaust emission considerations when designing for a vehicular gas turbine application. The development of each major component and the performance of the combustion system as a whole are reviewed. The satisfactory performance and durability potential of the GT-309 engine combustion system have been demonstrated by extensive operation in a component test facility and in several test cell and vehicle installed engines. Exhaust emissions of unburned hydrocarbons and carbon monoxide are minimal and are of no concern from an air pollution standpoint. No objectionable exhaust smoking and odor are produced.

During development of the General Motors rotary engine, the lubricant was recognized as important to its success because certain lubricants produced deposits which tended to stick both side and apex seals. Consequently, it was decided to develop a rotary engine-dynamometer test, using a Mazda engine, which could be used for lubricant evaluation. In an investigation using an SE engine oil with which there was rotary engine experience, engine operating variables and engine modifications were studied until the greatest amount of deposits were obtained in 100 h of testing. The most significant engine modifications were: omission of inner side seals, plugging of half the rotor bearing holes, pinning of oil seals, grinding of end and intermediate housings, and using a separate oil reservoir for the metering pump. Using this 100 h test procedure, three engine oils and five automatic transmission fluids were evaluated.

Secondary air scheduling and average delivery rate have a great influence on the performance (carbon monoxide and hydrocarbon cleanup) of rich thermal manifold reactors. A continuously modulated secondary air system was devised to provide a tailpipe air-fuel ratio that did not change significantly with engine speed or load when a “flat” carburetion calibration was incorporated. This system involved throttling the inlet of the air pump(s) so that the air pump and engine intake pressures were equal. The continuous air modulation system was compared with an unmodulated system and a step-modulated system. The secondary air systems were investigated with both GMR “small volume” cast iron thermal reactors and Du Pont V thermal reactors on modified 350 CID V-8 engines in 1969 Chevrolet passenger vehicles. It was found that thermal reactor performance improved with each increase in control of the secondary air schedule.

The development of a variable valve timing (VVT) camshaft was initiated as a potential means of controlling exhaust emissions from a spark ignition piston engine. This approach was based on the fact that valve overlap influences internal exhaust gas recirculation which in turn affects spark ignition engine emissions and performance. The design, fabrication, bench tests and engine durability tests of a unit incorporating splines to allow the intake cams to move relative to the exhaust cams is discussed. Preliminary test data from a 350 CID (5700 cm3) engine fitted with the VVT camshaft are discussed with regard to durability and emissions.

The tedious, time consuming task of hand reducing data from the California exhaust emission test has been alleviated through the use of digital data acquisition equipment and a digital computer. Analog signals from exhaust gas analyzers and an engine speed transducer are converted to digital measurements which are recorded on tape and submitted to a digital computer for data analysis and computation of results. In the data analysis, the computer identifies the required driving modes from engine speed changes, taking into account the sample delay time. “Reported” composite emissions determined by the automatic data reduction method agree within 5% with results determined by careful hand analysis of analog strip chart recordings. The results determined by the automatic data reduction system are more consistent and accurate because human errors prevalent in hand analysis have been eliminated, and because nonlinear analyzer response is accounted for.

The relationship between surface temperature and exhaust hydrocarbon concentration was explored by installing surface thermocouples at three locations in the combustion chamber of a single-cylinder engine. Coolant temperature, coolant passage surface scale, and ethylene glycol in the coolant affected exhaust hydrocarbon concentration through changes in surface temperature. As power output increased, combustion chamber surface temperature rose, and exhaust hydrocarbon concentration fell. The increase in surface temperature accounted for about 43% of the decrease in hydrocarbon concentration. The reason for the other 57% of the decrease is unknown, but it may have been caused by increasing gas temperatures in the quench zone. Increasing surface temperature by engine modification would be expected to have adverse effects on engine octane requirement, volumetric efficiency, and oil oxidation.

Platinum, palladium, and copper-chromium oxidation catalysts for exhaust emission control were exposed to exhaust gases from a steady-state engine dynamometer test in which the amount of oil consumed per unit volume of catalyst was high. When unleaded gasoline (0.004 Pb g/gal, 0.004 P g/gal) was used, conventional SE oil caused somewhat greater loss of catalyst activity than an ashless and phosphorus-free (“clean”) oil. Chemical analysis of the catalyst indicated that phosphorus from the conventional oil was probably responsible for the difference. However, a test run with low-lead (0.5 Pb g/gal, 0.004 P g/gal) gasoline and “clean” oil caused much greater catalyst activity deterioration than either of the tests with unleaded gasoline.

This study describes the effect of spark plug location on NO and HC emissions from a single-cylinder engine with a specially modified combustion chamber. The effects of changes in combustion duration caused either by spark location, dual spark plugs, or charge dilution on NO and HC emissions were also examined. Experiments were run at constant speed, constant load, and mbt spark timing. Nitric oxide emissions were the same with the spark plug located either near the intake or exhaust valve, but were higher with the spark plug midway between the valves or with dual ignition. Hydrocarbon emissions were lowest with the spark plug nearest the exhaust valve and increased with the distance of the spark plug from the exhaust valve. With charge dilution the decrease in NO emission was isolated into a pure dilution effect and a combustion duration effect. The combustion duration effect was minimal at rich mixtures and increased with air-fuel ratio.

Hydrogen-supplemented fuel was investigated as a means of extending lean operating limits of gasoline engines for control of NOx. Single-cylinder engine tests with small additions of hydrogen to the fuel resulted in very low NOx and CO emissions for hydrogen-isooctane mixtures leaner than 0.55 equivalence ratio. Significant thermal efficiency improvements resulted from the extension beyond isooctane lean limit operation. However, HC emissions increased markedly at these lean conditions. A passenger car was modified to operate at 0.55-0.65 equivalence ratio with supplemental hydrogen. Vehicle emissions, as established by the 1975 Federal Exhaust Emissions Test, demonstrated the same trends as the single-cylinder engine tests. The success of the hydrogen-supplemented fuel approach will ultimately hinge on the development of both a means of controlling hydrocarbon emissions and a suitable hydrogen source on board the vehicle.

Engine oil test Sequences IIA and IIIA have been developed to replace Sequences I, II, and III. These new sequences are designed to evaluate lubricants for use in current passenger car engines under severe (MS) service conditions. Lubricant performance is evaluated with respect to scuffing wear, rust, corrosion, deposits, and rumble. The Sequence IIA and IIIA test procedure involves major changes which affect the evaluation of engine rusting and provides improved correlation between test results and short-trip service. Average engine rust ratings correlate with service data within ±0.5 numbers. The new test also provides better repeatability and reproducibility in a significantly shorter schedule. The rust repeatability and reproducibility is less than ±0.2 and ±0.6 numbers, respectively. Test time has been reduced 52%.

The exhaust hydrocarbon and nitrogen oxide concentrations of a single-cylinder engine, operating on a 25% (wt.) ethyl alcohol – 75% gasoline fuel, are compared to those operating on gasoline. For comparisons at the same airfuel ratio but lower than 15.3, the addition of ethyl alcohol to gasoline reduces the exhaust hydrocarbon concentrations and increases the nitrogen oxide concentrations. At the same air-fuel ratio but higher than 15.3, the addition of ethyl alcohol reduces both the hydrocarbon and nitrogen oxide concentrations. However, tests with automobiles, operating at the same air-fuel ratio with both fuels, indicate that the addition of ethyl alcohol causes an increase in “surge” and, in some cases, results in a power loss. To overcome these performance problems, the ethyl alcohol-gasoline fuel should be operated at about the same percent theoretical air as gasoline.

Controlled-slip differentials (CSD) improve car operation under wheel slipping conditions. The performance of CSD's is dependent upon two criteria associated with clutch friction: “chatter” and “effectiveness.” “Chatter” is an undesirable noise which may occur during differential action. “Effectiveness” is a measure of the ability of the CSD clutches to transfer torque, during wheel slippage, to the wheel with the greater traction. The objective of this investigation was to definitely establish the cause of chatter, measure CSD effectiveness, and relate friction characteristics of lubricants to CSD operation. In tests with an instrumented car, it was found that both chatter and effectiveness are strongly influenced by the lubricant. Chatter occurred with lubricants that produced an increase in clutch friction with decreasing sliding speed. Chatter did not occur with lubricants containing friction modifiers which produced a decrease in clutch friction with decreasing sliding speed.

Two steam-powered passenger ears have been designed, built, and tested. The SE-101 is an intermediate sport coupe incorporating the comfort and convenience features of a modern passenger car and vehicle performance comparable to a low-powered automobile. The SE-124 is a very low-power intermediate sedan with manual start and semiautomatic control. The characteristics of these cars were evaluated relative to the operational requirements of current transportation needs, with particular emphasis on exhaust emissions. Start-up time, exhaust emissions, fuel economy, acceleration, and water consumption data are presented. Although any one of these characteristics may be improved at the expense of others, it does not appear that any compromise can satisfy all of the areas required by today's motorist.

The use of relatively small catalytic converters containing alumina-supported platinum (Pt) and palladium (Pd) catalysts to control exhaust emissions of hydrocarbons (HC) and carbon monoxide (CO) was investigated in full-scale vehicle tests. Catalytic converters containing 70-80in3 of fresh catalyst were installed at two converter locations on the vehicle. Carburetion was richer than stoichiometric, with air-fuel ratios (A/F) comparable to those proposed for dual-catalyst systems containing an NOx reduction catalyst. The vehicle was equipped with exhaust manifold air injection. Homogeneous thermal reaction in the exhaust manifolds played a significant role in the overall control of HC and CO. Four Pt catalysts, three Pd catalysts, and one Pt-Pd catalyst were prepared and evaluated. Total metal loadings were varied 0.01-0.07 troy oz. Hydrocarbon conversion efficiencies varied 62-82%, measured over the 1975 cold-hot start weighted Federal Test Procedure.

As part of General Motors effort to improve fuel economy, the effects of engine and power train lubricant viscosities were investigated in passenger car tests using either high- or low- viscosity lubricants in the engine, automatic transmission, and rear axle. Fuel economy was determined in both constant speed and various driving cycle tests with the car fully warmed-up. In addition, fuel economy was determined in cold-start driving cycle tests. Using low-viscosity lubricants instead of high-viscosity lubricants improved warmed-up fuel economy by as much as 5%, depending upon the differences in lubricant viscosity and type of driving. Cold-start fuel economy with low-viscosity lubricants was 5% greater than that with high-viscosity lubricants. With such improvements, it is concluded that significant customer fuel economy gains can be obtained by using the lowest viscosity engine and power train lubricants recommended for service.

Future low emissions engines will burn unleaded gasoline. Compared with engines of 1970, future engines will have lower concentrations of NOx in the blowby gases, and lower blowby flow-rates; however, oil temperatures will probably be unchanged. The consequences of these conditions for engines using high quality (SE) oils at current drain intervals are: virtual elimination of rust, reduction of sludge, no effect on wear and oil thickening, and possible worsening of varnish. Therefore, extension of the drain interval with SE engine oils in the future may be possible, but final decisions will depend on the findings of research in the areas of engine wear and varnish, and oil thickening.

The results of studies of atmospheric chemistry of smog formation serve as guidelines for determining a rational basis for control of vehicle emissions. These guidelines indicate the desirability of reactive hydrocarbon reduction and the futility of nitric oxide reduction from vehicles. A system of classifying hydrocarbons as to their reactivity in smog formation is presented. Its application, in combination with, gas chromatographic analyses, to both exhaust hydrocarbon and evaporative hydrocarbon vehicle emissions is illustrated. Utilization of this approach for determining the importance of exhaust versus evaporative hydrocarbon emissions, and for measuring efficacy of control by changes in both vehicles and fuel composition is recommended.

The intent of this paper is to put into proper perspective the relationships among the vehicle, the thermodynamic cycle, and the combustion process as they relate to exhaust emissions from a gas turbine-powered passenger car. The influence of such factors as car size, installed power, regeneration, and other cycle variables on level road load fuel economy, and on the production of oxides of nitrogen and carbon monoxide, are examined. In limited checks against experimental data, the mathematical model of the combustor used in this study has proved to be a reliable indicator of emission trends. The calculated emission levels are not final, however, with deficiencies subject to improvement as new combustor concepts are developed.

A five-vehicle, 64 000-km test with 7.45 litre V-8 engines was conducted to determine if synthetic engine oils provided performance sufficiently superior to that of conventional engine oils to permit longer oil change intervals. The results show better performance in two areas of deposit control; inferior performance with respect to wear protection; and essentially equivalent performance in the areas of fuel and oil economies. Based on these data, it was concluded that synthetic engine oils do not provide the necessary performance required to safely recommend their use for extended oil change intervals. In addition, a cost analysis shows that the use of synthetic engine oils, even at a change interval of 32 000 km, will essentially double the customers' cost compared with conventional engine oils at GM's current 12 000-km change interval.