Search Results

The problem associated with laboratory evaluation of muffler acoustical characteristics are complicated both by the acoustical considerations involved in obtaining an adequate noise source and by the ambiguities involved in defining what constitutes quality in a muffler built for general application. In order to quantitatively define the characteristics of quality mufflers, an extensive series of field tests were conducted on a variety of sizes and types of mufflers in conjunction with four engine configurations. Work then turned to the development of a wide band siren noise source and acoustical test system which would simulate the high impedance character of an engine exhaust noise source, and in addition generate the necessary intensity and spectral characteristics required to obtain test data over the range of noise conditions encountered in the field.

Until recently, U.S. government efforts to dramatically reduce emissions, greenhouse gases and vehicle fuel consumption have primarily focused on passenger car applications. Similar aggressive reductions need to be extended to heavy vehicles such as delivery trucks, buses, and motorhomes. However, the wide range of torques, speeds, and powers that such vehicles must operate under makes it difficult for any current powertrain system to provide the desired improvements in emissions and fuel economy. Hybrid electric powertrains provide the most promising, near-term technology that can satisfy these requirements. This paper highlights the configuration and benefits of a hybrid electric powertrain capable of operating in either a parallel or series mode. It describes the hybrid electric components in the system, including the electric motors, power electronics and batteries.

Geartrain noise can be a significant contribution to the overall sound level of diesel engines. Some engine manufacturers employ isolation solutions such as sound deadening covers and foam panels to combat the problem, but these add cost. Little has been published on geartrain noise reduction, and public standards for diesel geartrain design and development are not available. This paper describes an experimental study of the relative influence of gear design parameters on the rattle noise of a diesel engine timing geartrain. The geartrains of several diesel engines were benchmarked to determine the noise reduction strategies employed. A total of three gear sets were designed and tested in a 3.3L four cylinder normally aspirated diesel engine. The experimentation quantified the influence of an anti backlash idler gear in reducing gear rattle noise, and revealed that a key path for gear rattle noise transmission is through an idler gear journal bearing shaft.

The principles of the magnetic-perturbation method of flaw detection and the Barkhausen noise residual stress measurement method are briefly reviewed. It is suggested that they provide very powerful tools for assuring improved ball bearing performance. The methods are applied for the evaluation of ball bearing races. Typical experimental results are presented along with metallurgical sectioning correlation.

Alternative fuels made from materials other than petroleum are available for use in alternative fueled vehicles (AFVs) and some conventional vehicles. Liquid fuels such as biodiesel could be used in U.S. Army or other Military/Federal Government compression ignition (CI) engine powered vehicles. The military combat/tactical fleet is exempt from Federal Government mandates to use alternative fueled vehicles and has adopted JP-8/JP-5 jet fuel as the primary military fuel. The Army non-tactical fleet and other Federal nonexempt CI engine powered vehicles are possible candidates for using biodiesel. Inclusion of biodiesel as an alternative fuel qualifying for alternative fueled vehicle credits for fleets required to meet AFV requirements has allowed for its use at 20 (minimum) percent biodiesel in petroleum diesel fuel. Alternative fuels are being considered for the 21st Century Truck (21T) program. [1]

This paper describes the potential for the use of Dedicated EGR® (D-EGR®) in a gasoline powered medium truck engine. The project goal was to determine if it is possible to match the thermal efficiency of a medium-duty diesel engine in Class 4 to Class 7 truck operations. The project evaluated a range of parameters for a D-EGR engine, including displacement, operating speed range, boosting systems, and BMEP levels. The engine simulation was done in GT-POWER, guided by experimental experience with smaller size D-EGR engines. The resulting engine fuel consumption maps were applied to two vehicle models, which ran over a range of 8 duty cycles at 3 payloads. This allowed a thorough evaluation of how D-EGR and conventional gasoline engines compare in fuel consumption and thermal efficiency to a diesel. The project results show that D-EGR gasoline engines can compete with medium duty diesel engines in terms of both thermal efficiency and GHG emissions.

This paper analyzes the hybridization of a conventionally powered light duty front wheel drive pick up truck by adding an electric motor driven rear axle. Also studied are the effects of using propane fuel instead of gasoline. This hybrid powertrain configuration can be described as a parallel hybrid electric vehicle. Supervisory power management control has been developed to best determine the proportion of load to be provided by the engine and/or electric motor. To perform these analyses, a simulation tool (computer model of the powertrain components) was developed using MATLAB/SIMULINK'. The models account for the thermal and mechanical efficiencies of the components and are designed to develop control strategies for meeting road loads with improved fuel economy and reduced emissions. Results of this study have shown that fuel economy can be improved and emissions reduced using commercially available components (motor, rear axle, and lead acid batteries).

Life prediction and reliability analysis of a cam roller system were investigated. From the tribological analysis, the cam roller system was found to operate under low film parameter conditions and components were subjected to the risk of contact fatigue. Surface analysis performed on the failed rollers indicated that the surface distress was the primary cause for failure. Then, numerical analyses were performed to evaluate the cam roller life and its related reliability. The adopted approach combined a contact fatigue crack growth calculations with a probabilistic model for controlling the design uncertainty. The computation-efficient Fast Probabilistic Integration (FPI™) code was used to solve the problem. With appropriate descriptions for uncertainty distributions, the surface fatigue life of the specified cam roller system can be predicted along with a confident reliability level.

To aid in the catalytic converter design and development process, a test apparatus was designed and built which will allow comparative evaluation of the durability of candidate mat materials under highly controlled thermal and vibration environments. The apparatus directly controls relative shear deflection between the substrate and can to impose known levels of mat material strain while recording the transmitted shear force across the mat material. Substrate and can temperatures are controlled at constant levels using a resistive thermal exposure (RTE) technique. Mat material fatigue after several million cycles is evident by a substantial decrease in the transmitted force. A fragility test was found to be an excellent method to quickly compare candidate materials to be used for a specific application. Examples of test results from several materials are given to show the utility of the mat material evaluation technique.

In order to further reduce vehicle cold-start emissions, the use of catalytic converters that are “close-coupled” to the exhaust manifold is increasing. To understand the vibrational environment of close-coupled and underbody converters, a laboratory study was conducted on several passenger vehicles. Catalytic converter vibration spectra were measured on a chassis dynamometer with the vehicle operating over a variety of test conditions. Vehicle operating conditions included hard accelerations and extended steady-state speeds at distinct throttle positions over zero-percent and four-percent simulated road grades.

Many studies on low speed pre-ignition have been published to investigate the impact of fuel properties and of lubricant properties. Fuels with high aromatic content or higher distillation temperatures have been shown to increase LSPI activity. The results have also shown that oil additives such as calcium sulfonate tend to increase the occurrence of LSPI while others such as magnesium sulfonate tend to decrease the occurrence. Very few studies have varied the fuel and oil properties at the same time. This approach is useful in isolating only the impact of the oil or the fuel, but both fluids impact the LSPI behavior of the engine simultaneously. To understand how the lubricant and fuel impacts on LSPI interact, a series of LSPI tests were performed with a matrix which combined fuels and lubricants with a range of LSPI activity. This study was intended to determine if a low activity lubricant could suppress the increased LSPI from a high activity fuel, and vice versa.

While initial Connected Vehicle research in the United States was focusing almost exclusively on passenger vehicles, a program was envisioned that would enhance highway safety, mobility, and operational efficiencies through the application of the technology to commercial vehicles. This program was realized in 2009 by funding from the I-95 Corridor Coalition, led by the New York State Department of Transportation, and called the Commercial Vehicle Infrastructure Integration (CVII) program. The CVII program focuses on developing, testing and deploying Connected Vehicle technology for heavy vehicles. Since its inception, the CVII program has developed numerous Vehicle-to-Vehicle and Vehicle-to-Infrastructure applications for trucks that leverage communication with roadside infrastructure and other light and heavy duty vehicles to meet the objectives of the program.

Vehicle to Everything (V2X) communication has enabled on-board access to information from other vehicles and infrastructure. This information, traditionally used for safety applications, is increasingly being used for improving vehicle fuel economy [1-5]. This work aims to demonstrate energy consumption reductions in heavy/medium duty vehicles using an eco-driving algorithm. The algorithm is enabled by V2X communication and uses data contained in Basic Safety Messages (BSMs) and Signal Phase and Timing (SPaT) to generate an energy-efficient velocity trajectory for the vehicle to follow. An urban corridor was modeled in a microscopic traffic simulation package and was calibrated to match real-world traffic conditions. A nominal reduction of 7% in energy consumption and 6% in trip time was observed in simulations of eco-driving trucks.

An Emergency Tire Inflation System (ETIS) designed for use on commercial trucks was evaluated and tested. The ETIS is provided in kit form and designed to be installed by a truck operator to provide emergency air to inflate a low or punctured tire on tractor drive axles. The ETIS will continue to supply air to the tire until the system pressure falls below a safe air pressure level. The system is designed to allow the rig to be driven 500 miles to a tire repair station or to a safe location where tire repair service is available. The installation kit (Figure 1), which can fit under a truck seat, includes all the necessary equipment to install the system on the most common drive axles. The ETIS supplies air to the under-inflated tire through a previously qualified1 Rotary Union design. The Rotary Union is attached to the axle flange of the drive axle by a threaded adapter and two adjustable links that allow the Rotary Union to be placed at the center of rotation of the axle.

Range-extended hybrids are an attractive option for medium- and heavy-duty commercial vehicle fleets because they offer the efficiency of an electrified powertrain with the driving range of a conventional diesel powertrain. The vehicle essentially operates as if it was purely electric for most trips, while ensuring that all commercial routes can be completed in any weather conditions or geographic terrain. Fuel use and point-source emissions can be significantly reduced, and in some cases eliminated, as many shorter routes can be fully electrified with this architecture. Under a U.S. Department of Energy (DOE)-funded project for Medium- and Heavy-Duty Vehicle Powertrain Electrification, Cummins has developed a plug-in hybrid electric Class 6 truck with a range-extending engine designed for pickup and delivery application.

Tier 2, bin 5 diesel engines may use multiple combustion modes to achieve stringent emissions requirements. Unfortunately, switching between different combustion modes can cause step changes in noise that will be unacceptable to consumers. In this paper, several sound quality metrics are evaluated for their ability to quantify the NVH issues that arise during a rich pulse event. In addition, techniques are presented that allow an engine developer to reduce the NVH effects caused by changing combustion modes. Careful calibration tuning in close cooperation with performance and emissions development engineers is required to solve noise problems that arise from combustion mode switching events, since an NVH improvement may often come at the expense of a performance or emissions issue.

This web course provides an in-depth overview of diesel engine noise including combustion and mechanical noise sources. In addition, the instructor will discuss a system approach to automotive integration including combining sub-systems and components to achieve overall vehicle noise and vibration goals.

Current industry trends in both powertrain electrification and vehicle drag reduction point towards reduced peak and average power demands from the internal combustion engine in future long-haul class 8 vehicles. Downsizing the engine displacement to match these new performance requirements can yield a benefit in drive cycle efficiency through reduced friction and improved cruise load efficiency. Downsizing by reducing cylinder count avoids the heat loss and friction penalties from reduced per-cylinder displacement and could allow a manufacturer to continue to leverage the highly optimized combustion system from existing heavy-duty engines in the new downsized offering. The concept of this study is to leverage powertrain electrification and the improvement trends in vehicle aerodynamics and rolling resistance to develop a fuel economy focused, downsized heavy duty diesel powertrain for future long-haul vehicles utilizing a reduced cylinder count.

Electromagnetic emissions (EME) from vehicles and their effect on broadcast radio and television were studied as early as 1944. Their original effect was significantly reduced by the early 1960s. Today, ignition noise (broadband) and vehicular micro-processor-controlled system noise (narrowband) are interfering with Land Mobile (two-way) communication services and other devices such as computers. Two SAE test methods, J551 and J1816, are used to measure this EME. Under development are methods to measure conducted EME on vehicle signal wiring and power input leads. This paper discusses EME measurement methods, provides insight into the sources of EME problems, and gives information on the test instrumentation used to make these measurements. This paper is the third in a series of papers on electromagnetic compatibility (EMC) in the off-highway vehicle. The first paper was an overview of a complete EMC program with discussion of several important segments.

Antilock brake systems for air braked vehicles have been growing in popularity in Great Britain and Europe and appear to be candidates for extensive use in the United States as well. Previous mandated use in the United States during the 1970's was not successful, in part because of reliability problems, and the National Highway Traffic Safety Administration (NHTSA) has decided that a thorough evaluation of air brake antilock systems is necessary prior to any decision about the appropriateness of future mandatory use in the United States. This paper describes the electronic data collection equipment and processing techniques which are being used in the NHTSA 200 truck evaluation project. Detailed maintenance histories for each truck are being recorded manually as a separate segment of the project. An average of 6 to 7 megabytes of data per week is being collected in the various cities in which fleets are operating test vehicles.