Search Results

The acoustical performance of a vehicle dash panel system is rated by the noise reduction, which is calculated from the sound transmission and absorption characteristics. A typical dash insulator consists of a steel panel (vehicle body panel), a porous decoupler and heavy layer in the form of sandwich construction. The use of dash panel is to block engine noise from entering into the interior cabin. In the present study the transmission loss of dash panel has been evaluated in reverberation chambers and the sound absorption of dash panel has been determined in impedance tube. This paper deals with improving over all sound transmission loss and shifting of the double wall resonance well below the engine firing frequencies by changing the decoupler materials such as felt and foams of different density and thickness and heavy layer mass per unit area.

In today’s automotive industry sound package material design and optimization is important considering the need for weight reduction and achieving targeted sound absorption and sound transmission loss values. As per traditional approach vehicle level noise reduction targets are defined considering flat samples, but in actual vehicle condition molded trimmed parts are used. This paper discusses about the systematic methodology developed for molded sample characterization in terms of BIOT’s properties. Effects of different parameters like area wise thickness variation, density variation on BIOT properties is studied. Comparison of BIOT’s properties of flat and molded dash sample is done to study the effect of molded structure. Using these BIOT’s properties prediction of sound absorption and sound transmission loss results carried out using FTMM approach for flat sample and SEA approach for molded sample.

Air pollution in India and also global warming are two major concern in the country. To address this situation, India is moving from BS-IV to BS-VI for on-road applications with 90% reduction in NOx and 50% in PM with limit on particulate number. Also moving to Trem-IV and Trem-V for off-road applications subsequently. It needs higher efficiency after-treatment systems like SCR and DPF to achieve such lower emission levels. Addition of these complex after-treatment system, severely increase the cost of diesel power plant with heavy penalty on fuel economy. Hence, it is challenge to auto industry to reduce the complexity and cost, so that it requires an alternate solution to reduce NOx and PM emissions at source to reduce cost and system complexity. Low Temperature Combustion (LTC) is a potential concept to reduce the NOx and PM emissions simultaneously.

Dual Phase (DP) steels with their high energy absorbing capacity are fast emerging as materials for automotive body applications with improved crashworthiness. The unique combination of high strength and good ductility associated with the DP steels originates from its specially developed microstructure that consists of martensitic islands in ferritic matrix. The high strength and good ductility are expected to give very good resistance to fatigue crack generation and propagation respectively. This paper discusses the fatigue properties determined for a DP steel grade viz. DP 800. The strain controlled fatigue tests were carried out on the un-notched specimens prepared from 1.2 mm sheets to generate E-N curves. The force controlled axial fatigue tests were carried out on two types of specimens prepared from 1.2 mm sheets to generate S-N curves for two Stress Concentration Factors (SCF) viz. 2.5 and 4.4.

The present study discusses the effects of engine combustion, performance and emission features of methanol-gasoline blend fired lean burn Spark Ignition (SI) engine. Performance features such as Brake Power (BP), Brake Specific Fuel Consumption (BSFC), Brake Thermal Efficiency (BTE), tail pipe emissions namely Hydrocarbon (HC), Carbon Monoxide (CO), Nitrogen Oxide (NO), Carbon di Oxide (CO2) and combustion characteristics viz. in-cylinder pressure, Heat Release Rate (HRR), Cumulative Heat Release (CHR) and variation of mean effective pressure were measured and compared with that of neat gasoline. Experiments were conducted on a modified sole cylinder four-stroke compression engine (Kirloskar TAF1) to operate as SI engine with a compression ratio of 10.5:1. A new manifold injection system and ignition system were developed by replacing the fuel injection pump and injector.

In this work, the effect of tool rake angle and cutting speed on residual stresses of tool was studied, the rake angles of 0°, 5°, 10°, 15°, and 20° and a constant clearance (Relief angle) of 8° were used to turn bright mild steel on the lathe machine, A total of 15 experiments were carried out with three different cutting speeds (37.69, 59.37, 94.24 m/min) for each rake angle, keeping the feed rate and depth of cut constant. During the experimentation, the residual stresses were measured using an x-ray diffractiometer. This is all in order to explore the energy savings opportunities during regrinding of tools, useful production time and energy is being wasted due to regrinding or re-sharpening of tools when cutting tools got worn or blunt, selection of the rake angle which generate the optimum residual stresses in the tool, goes a long way in saving these time and energy.

Automobile industry is shifting towards lighter materials in order to meet the high strength to weight ratio as required for better performance, safety, and environmental concern. The objective of this review is to evaluate and compare the different advanced and light weight materials like advanced high strength steel (AHSS), Magnesium and Aluminium alloys, which will help in selection of appropriate materials for their intended application. In this paper comparison of materials on the basis of their current, applications, limitations, cost, potential future applications and percentage wise use in automotive vehicles are discussed. Solutions and suggestions are discussed to overcome the limitations of materials which will widen their future application. Case studies and charts for cost evaluation of different materials, on the basis of structural properties like stiffness and strength are also discussed.

Light weighting is significant in for automotive industry as it helps in less fuel consumption and to achieve better performance. Aluminium is a candidate material for light weighting. To design a component made of aluminium material, it is necessary to understand the fatigue performance of the material. In this paper, a study is carried out to understand the fatigue performance of aluminium 6xxx series alloys at an early stage of design without carrying out comprehensive fatigue testing. Coffin Manson Parameters are used to predict fatigue life. This research focusses on determining the gaps in existing models for aluminium alloys by carrying out comprehensive review of various models developed for 6xxx series which uses monotonic tensile data. Two models are developed and the predicted fatigue properties for this class of material are further compared with experimental fatigue, monotonic data and literature.

The objective of this study is to develop, demonstrate and validate the methodology of external aerodynamic analysis of a State Road Transport bus for prediction of drag coefficient and its impact on fuel consumption with experimental validation. It has been verified that vehicle consumes around 40% of the available engine power to overcome the air drag. This gives us a huge scope to study the effect of aerodynamic drag. Baseline model of State Road Transport Bus was evaluated for estimating fuel consumption using Computational Fluid dynamics (CFD) methodology. The CFD results were validated with the experimental data with less than 10% deviation. Bus design was optimized with an objective of reducing the fuel consumption with parameters like angle of windshield, rounding and tapering corners and rear draft angle. Optimized bus design is also ensured to meet functional specifications as per AIS052.

Future emission limits for off-highway application engines need advanced power train solutions to meet stringent emissions legislation, whilst meeting customer requirements and minimizing engineering costs. DI diesel engines with four valves per cylinder are widely used in off- highway applications because of the fundamental advantages of higher volumetric efficiency, lower pumping loss, symmetric fuel spray & distribution in combination with the symmetric air motion which can give nearly optimal mixture formation and combustion process. As a result, the fuel consumption, smoke levels and exhaust emissions can be considerably reduced. In particular, the four-valve technology, coupled with mechanical low pressure and electronic high pressure fuel delivery systems set different requirements for inlet port performance. In the present paper four valve intake port design strategies are analysed for off highway engine using mechanical fuel injection systems.

The effect of different cold- rolling and cryo-rolling routes on the strength and ductility of Al-6061 alloy was thoroughly investigated. Rolling decreased the grain size and increased the strength according to the Hall-Petch relationship. However subjecting the samples to ageing at different temperatures and for different time period increased the strength and improved the ductility. The ductility was improved due to the rearrangement and even decrease in dislocation density due to recovery and recrystallization during ageing while the strength was maintained due to ageing. Evolution of microstructure was investigated by optical microscopy, scanning electron microscopy. Preliminary hardness measurements coupled with tensile tests indicate the improvement of both yield strength and ductility. The disparity in ultimate tensile strength, yield strength and the elongation to failure with different ageing temperatures and for different time period is determined and discussed.