Search Results

Since the advent of the turbojet engine, there has been much research by aircraft and engine manufacturers into the source of aircraft noise and its reduction. A review of this research is presented delineating the transition from turbojet engines to turbofan engines to the high by-pass ratio engines being introduced today, and the progress that has been made. Application of the current state-of-the-art to existing airplanes through engine replacement, nacelle retrofit, and flight procedures are also discussed.

An overview of composite structure required for manned orbiting space stations is presented. Following a brief introduction of typical configurations and major subsystems, the major structural areas requiring composite structure and their particular functions and requirements are discussed. A summary weight breakdown is presented to assess the dependence of launch weight on these areas. To illustrate, the primary wall composite structure is presented in detail. The design interplay of boost, pressure, meteoroid, radiation, and thermal control requirements are presented. Resultant composite structure for each remaining major structural area is presented in summary form with a brief description of typical design compromises required.

A review of the current extended-range twin-engine operations (ETOPS) and the modifications to the standards and processes that led to its successful operational record has contributed to the feasibility of developing an airplane and preparing an operator for ETOPS at entry into service. The airplane and engine manufacturers and component suppliers have continued to expand on these modified standards and processes in their design, build, test and support programs to meet regulatory authority ETOPS requirements and to facilitate the development of regulatory authority criteria for substantiating ETOPS capability prior to entry into service. Airlines, in conjunction with the manufacturers, have also developed improved processes that meet regulatory authority requirements for preparing an operator to integrate a new airplane into its existing ETOPS programs at entry into service.

There are a large number of space structures, orbital replacement units (ORUs) and other components that must be transported to orbit on a regular basis for the assembly and maintenance of the International Space Station (ISS). Some of this hardware will be ferried on the Spacelab Logistics Pallet (SLP), which has a long and reliable history of space flight successes. The carrier is well used, well qualified, and very adaptable for repeated use in accommodating cargoes of various sizes and shapes. This paper presents an overview of past, present and future hardware design solutions that accommodate EVA operations on the SLP. It further demonstrates how analysis techniques and design considerations have influenced the hardware development, EVA operations, and compliance with human engineering requirements for the SLP.

Two spindles are discussed in this paper. The first spindle was installed on nine C-frame riveters on the 737/757 wing line at the Boeing Renton facility. Due to discontinuing the use of Freon coolant and cutting fluid, the C-frame riveters had difficulty shaving 2034 ice box rivets with the existing 6000 RPM hydraulic spindles. The solution was to install electric 30,000 RPM shave spindles inside the existing 76.2 mm (3 in.) diameter hydraulic cylinder envelope. The new spindle is capable of 4 Nm (35 in. lbs.) of torque at full speed and 110 kgf (250 lbs.) of thrust. Another design of interest is the Electroimpact Model 09 spindle which is used for 20,000 RPM drilling and shaving on wing riveting systems. The Model 09 spindle is a complete servo-servo drilling system all mounted on a common baseplate. The entire spindle and feed assembly is only 6.5″ wide.

The evolution of a manufacturing organization toward “Lean” manufacturing does not necessarily come cheaply or quickly. It is the experience at Boeing that technology and different visions can dramatically impact the evolutionary process-consuming great amounts of time and resources. The Boeing of Spokane case study, where aircraft floor panels are manufactured1, is but one of several case studies that suggests moving to “Lean” manufacturing is usually done in large steps, not small ones. These initial steps can be costly unless the systems (equipment and workforce) are flexible. Workforce flexibility is dependent on the attitude in the workforce as both touch and support labor move from their comfort zone to try new approaches and job descriptions. The workforce must be properly motivated to make the change. The equipment must also be flexible in adapting to new line layouts, product mixes, and process change or large cost penalties will be incurred.

Gas turbines have demonstrated their practicability in trucks, particularly those needing high horsepower and light weight combined with agility and reliability. These are the primary requirements of emergency vehicles such as fire fighting pumpers and crash trucks. Several installations powered by Boeing gas turbines are described, and comparisons to reciprocating engines are made. For vehicles of high power/weight ratio, the built-in torque converter feature of two-shaft gas turbines provides the automatic transmission feature that is needed for high density traffic operation or for hilly terrain. Trends in gas turbine design are briefly mentioned along with other system requirements for emergency vehicles.

This paper presents a detailed overview of the advantages and benefits of using 2-D barcodes, called Data Matrix codes, on Wing Fastening System (WFS) Tooling. This project was conducted on, but not limited to, the 777 Wing Fastening System (GEMCOR) tooling including the drills, fingers, and button dies. This paper will show how using Data Matrix codes to identify tooling will: Eliminate excessive downtime due to the operator using the incorrect tooling for a given tool setup. Reduce the cost associated with panel rework due to the use of incorrect tooling. Reduce the cost associated with excessive tool inventory or last minute ordering to keep up with production needs. Track tool life information for each specific tool. Provide operators with an easy to use tool setup reference document. And provide the factory with the ability to trace panel damage or defects back to the specific machine and exact tooling used.

The Space Station program was faced with a unique design environment-to design a common systems and payload support structure that could accommodate changeout for repair or technology growth over a 30-year lifetime. The vibration environment and weight allocation for rack structure necessitated a lightweight, yet stiff structure. The design answer was a modular rack structure using graphite/epoxy composites and selected aluminum components that could support a wide variety of systems, payload and stowage functions. A modular set of mounting locations allow the installation of a wide variety of secondary structures without permanent modifications to the rack. Aircraft-style seat track rails on the front edges of the rack permit attachment of handrails, foot restraints and accessories such as lights, fans, clipboards or computers to the rack face.

The process of developing a Payload Attach System (PAS) which will support a wide range of experimental and commercial payloads on the International Space Station (ISS) has experienced an interesting evolution during its design, development, test and evaluation (DDT&E) phase. This evolution has been caused in large measure by requirements intended to insure compatibility of the PAS with the extravehicular activity (EVA) crewmember during nominal and contingency operations in and around the PAS sites. As the design of the ISS transitioned from its Freedom predecessor, the effort to keep costs down by preserving as much of the original Freedom design as possible led to design decisions that challenged engineering thinking.

In this lecture, a review of Boeing commercial transport models is presented in chronological order from the B-1 flying boat of 1919 to the 747. The problems of air transport systems including convenience, reliability, safety, comfort, performance, and financial and environmental costs are discussed. The probability of more severe future problems is considered, and suggestions are offered as to technology and system improvements which may need to be pursued if civil air transport systems are to continue to provide fast, convenient transportation with a high level of public acceptance.

The International Space Station (ISS) Temperature and Humidity Control/Intermodule Ventilation (THC/IMV) system for the U.S. Lab provides required cooling air for the U.S. Lab and also provides “parasitic” cooling air for Node 1 and its attached elements. This scheme provides cooled air from the Lab THC directly to Node 1 and also to elements attached to Node 1, at different stages of Space Station assembly. This paper reports on the results of Open Hatch ECLSS/ TCS Tests for International Space Station’s Lab Module. The hardware tested is referred to as proto-flight hardware. Upon satisfactorily passing these Open Hatch and later Closed Hatch, imposed ground based, proto-flight tests, the proto-flight hardware will become flight hardware. The Lab Module is scheduled for launch during late 1999. The particular ECLSS/TCS equipment discussed here are the Temperature Humidity and Control (THC) equipment and Intermodule Ventilation (IMV) equipment.

Traditional thermal design criteria for avionics equipment are reviewed. Several studies have recently been conducted on the F-15 to assess accuracy of these design criteria. An overview of the study approach and results are presented. Specific topics investigated include: emergency cooling air provisions, cold start-up, hot start-up, normal and transient bay temperatures, and altitude design. The results indicate that many existing design criteria are overly conservative. The study findings suggest that reform of the existing thermal specification process is needed. Many of these reforms are applicable to the general aerospace industry and may result in significant acquisition cost savings as a result of the trend toward usage of commercial electronic parts. The reforms suggested include a new performance based thermal specification approach that increases emphasis on aircraft usage and frequency of occurrence. New transient design criteria are also recommended.

The International Space Station (ISS) Temperature and Humidity Control (THC) system has been designed with the intent of supplying the air cooling needs of various elements from the U.S. Lab heat exchanger assembly. Elements without independent air cooling capability are known as “parasitic” elements; these are Node 1, the Cupola, and the Mini Pressurized Logistics Module (MPLM). Analysis results are presented which show expected temperatures in the MPLM, and Node 1, as various heat loads are present in the respective elements. Analyses within this paper are coordinated with the results obtained from the Development Test of the complex USL/Node 1 integrated ducting system. This test was conducted in the summer of 1995, at the McDonnell Douglas test facility in Huntington Beach, California.

The fuel system installed in the Boeing Model 747 airplane is described in general, and the pressure fueling system treated in detail. The general treatment includes description of fuel tanks, engine fuel feed system, fuel jettison system, defueling system, fuel quantity indicating system, and fueling system. The component parts of the pressure fueling system are described, and performance of the system is evaluated. In the design of the 747 airplane, surge pressures and static electrification, possible problem areas associated with refueling large airplanes, have been minimized. The fuel system of the 747 meets applicable Federal Aviation Regulations and customer requirements.

This paper presents the basic test data obtained from tests of a cabin air distribution system in a simulated Space Station U.S. Lab-A module. The cabin air distribution system controls the flow of air in the open space of a Space Station module. In order to meet crew comfort criteria the local velocities for this cabin air are required to be distributed within a specified range with upper and lower limits. Achieving this desired velocity distribution is dependent upon the: (1.) design of the cabin air supply equipment and cabin air return equipment, (2.) total flowrate of air supplied to and subsequently returned from the cabin, and (3.) interactive effects of any other additional air flow streams which enter and exit the cabin. The basic Space Station design for the cabin air supply and air return equipment was used in this test program. Only directional adjustments to vanes in supply air diffusers were made during the test.