Search Results

Knowledge of the loads experienced by a leaf spring suspension is required for the optimal design of the suspension components and frame. The most common method of representing leaf springs is the SAE 3 link model, which does not give good results in the lateral direction. In this paper, a beam element leaf spring model is developed. This model is validated using data obtained from laboratory tests done on leaf spring assemblies. The model is then subjected to actual road load data measured on the Proving Ground. Lastly, results from the beam element model are presented and compared with results obtained from proving ground tests. Overall, the beam element model gives good results in all directions except in situations where it is subjected to high fore/aft acceleration and high reverse braking events.

Tire stiffness can have a significant effect on the spindle and component loads. While its’ effect on the component loads may show a different trend. This paper deals with data acquisition loads using Wheel Force Transducer (WFT) with 17 inch, 18 inch and 20 inch tires and shows how the spindle loads changed for different tire. These loads are applied on the analytical suspension model to generate both component and the body attachment loads. Some of the measured channels are correlated for all the wheel sizes for multiple events to ensure the confidence in the model. It is found that even if spindle loads are increased with tire stiffness, the component loads do not necessarily show a similar trend. This paper studies why higher spindle forces do not always give higher component loads and what are the possible alternatives one may look into to shortlist or select one set of loads over the other.

Exhaust durability is an important measure of quality, which can be predicted using CAE with accurate mount loads. This paper proposes an innovative method to calculate these loads from measured mount accelerations. A Chrysler vehicle was instrumented with accelerometers at both ends of its four exhaust mounts. The vehicle was tested at various durability routes or events at DaimlerChrysler Proving Grounds. These measured accelerations were integrated to obtain their velocities and displacements. The differences in velocities and displacements at each mount were multiplied by its damping and stiffness rates to obtain the mount load. The calculation was conducted for all three translational directions and for all events. The calculated mount loads are shown within reasonable range. Along with CAE, it is suggested to explore this method for exhaust durability development.

A method to predict the powertrain mount loads is proposed and correlated with measured data. DOE studies are performed to derive the sensitivity of several variables, including the range, root mean square, pseudo-damage values of powertrain mount loads, on some model parameters, including powertrain CG locations, moments of inertia, and mount stiffnesses, respectively. The results show that the proposed method is valid in predicting powertrain mount loads.

In this paper, we study the sensitivity of a vehicle impact harshness (IH) performance to the suspension bushing rates. A mid-sized uni-body SUV is selected for this study, with the acceleration responses at the driver seat track and the steering wheel as objective functions. A sensitivity study is conducted using an ADAMS full vehicle model including a tire model and flexible body structure representation over an IH event. The study resulted in the identification of key bushings that affect the IH performance and its sensitivity to the bushing rates. Based on the results, we came-up with an “optimal” bushing set that minimizes impact harshness, which was subjectively verified to result in significant improvement in IH.

In this study, a full vehicle with durability tire model established with ADAMS is applied to simulate the dynamic behavior of the vehicle under severe rough road proving ground events, where the shock force-velocity characteristics are modeled as nonlinear curves and multi-stage representations, respectively. The shock forces and velocities at each corner are resolved and through full factorial DOE, the shock forces and velocities response surface models are established to analyze the sensitivities of shock force and velocity to the shock damping characteristics.

Engine mount loads are mostly measured from load cells or calculated from measured engine accelerations. This paper introduces an innovative new method to calculate engine mount loads from measured spindle loads. The method starts from calculating suspension attachment loads to body or chassis frame, then calculating engine center of gravity accelerations, and finally calculating engine mount loads from engine inertia forces. This spindle-based engine mount load analysis method is validated by a vehicle with measurements by wheel force transducers and engine load cells. The correlation includes load time history, peak-to-peak load range, and pseudo-damage values. The correlations show good comparisons between measured and predicted in all the categories, especially for the high load components. It is recommended to implement this method in early vehicle design phases.

In this paper, a comprehensive evaluation index for impact harshness (IH) is proposed. A mid-sized uni-body SUV is selected for this study, with the acceleration responses at the various vehicle body locations as objective functions. A sensitivity study is conducted using an ADAMS full vehicle model with flexible body structure representation over an IH event to analyze the influence of various suspension tuning parameters, including suspension springs, shock damping, steer gear ratio, unsprung mass, track-width, and bushing stiffness.

Transmission mounts are usually tested as an assembly and typically only translational stiffnesses are provided. The torsional stiffness of the assembly is traditionally estimated based on experience in load simulation and analysis. This paper presents a procedure to estimate the torsional stiffness of the transmission mount assembly by using the test data. The effects of the torsional stiffness on the simulation results are also discussed.

This paper introduces a reliable method to calculate body mount loads from wheel-force-transducer (WFT) measurements on framed vehicles. The method would significantly reduce time and cost in vehicle development process. The prediction method includes two parts: Hybrid Load Analysis (HLA) that has been used by DaimlerChrysler Corporation and Body Mount Load Analysis (BMLA) that is introduced by this paper for the first time. The method is validated on a body-on-frame SUV and a pickup truck through one proving ground events. The example shown in this paper is for a SUV and one of the most severe events. In HLA, the loads at suspension-to-frame attachments are calculated from spindle loads measured by WFT. In BMLA, body mount loads were calculated using outputs of HLA with detailed finite-element-modeled frame and body. The loads are compared with measured body mount loads. The comparisons are conducted in range, standard deviation (S.D.), and fatigue pseudo-damage.

Accurate motion prediction can be used to evaluate vibrations at seat track and steering wheel. This paper presents the prediction and correlation of truck frame motion from wheel force transducer (WFT) measurements. It is assumed that the method can be used to predict vibrations at seat track and steering wheel for unibody vehicles. Two durability events were used for calculation. WFT measurements were used as inputs applied on frame from suspension. Frame loads were then used as inputs to calculate frame motions using a FEA approach. The predicted frame motions are represented by four exhaust hangers and they are compared with measured motions of the same locations. The correlations include displacement, velocity, and acceleration. It is shown that good correlations are obtained in velocity and displacement. Acceleration shows bigger differences than velocity and displacement.