Search Results

A new experimental method, that enables to estimate the body and driveline sensitivity to unit transmitting error of a hypoid gear for automotive rear axle gear noise, has been developed. Measurements were made by exciting the tooth of the drive-pinion gear and that of the ring gear separately using the special devices designed with regard to simulation of acceleration and deceleration. The characteristic of this method is to estimate the forces at the contact point of the gears. Estimation of these forces is carried out under the condition that the higher stiffness is provided by the tooth of the drive-pinion gear and that of the ring gear, compared with the stiffness of the driveshafts and that of the propeller shaft etc., and relative angular displacement of the torsional vibration between the teeth of the drive-pinion gear and those of the ring gear is constant.

The authors developed a useful analysis method of the rotational-angle of gear under transient state using the Hilbert Transform because the conventional method was not available under the transient state. Here, under the transient state the gear revolution speed was changed from 600r/min to 2000r/min in 0.35 seconds. A key technology of this method was that Hilbert Transform method, which used to be applicable only for steady data was improved so that it could treat transient data. Hence, the following procedures were developed. 1. The rotation of gear-teeth was detected by a gap-sensor pair, which can cancel the measuring error due to fluctuation of gear shaft. 2. The frequency of such signals varied significantly by the gear-revolution speed. Transient gear-teeth detection signals obtained at a constant sampling rate were converted to almost-constant frequency signals over the data series axis using a trigger pulse obtained per gear revolution.

Vehicle stability after releasing the accelerator during limit cornering (from now on “Tuck-in”) is the behavior that the turning radius of a vehicle gets smaller after releasing the accelerator. This paper presents that the main factors of yaw moment variation by releasing the accelerator are the change of lateral forces due to longitudinal transfer of normal loads, lateral shift of vehicle center of gravity due to vehicle roll and tire lateral deflection, and the change of lateral forces due to deceleration. It also shows that roll stiffness distribution and longitudinal acceleration have an influence through the formulation of turning radius ratio.

The recent growth of available computational resources has enabled the automotive industry to utilize unsteady Computational Fluid Dynamics (CFD) for their product development on a regular basis. Over the past years, it has been confirmed that unsteady CFD can accurately simulate the transient flow field around complex geometries. Concerning the aerodynamic properties of road vehicles, the detailed analysis of the transient flow field can help to improve the driving stability. Until now, however, there haven’t been many investigations that successfully identified a specific transient phenomenon from a simulated flow field corresponding to driving stability. This is because the unsteady flow field around a vehicle consists of various time and length scales and is therefore too complex to be analyzed with the same strategies as for steady state results.

A communication system that uses roadside beacons to broadcast road and traffic information and private messages to vehicles has been developed. The system, called Road/Automobile Communication System (RACS), was the result of a joint research project involving the Public Works Research Institute and 25 private-sector corporations. This paper contains an outline of RACS and of an onboard system developed by TOYOTA and presents the results of field tests conducted in the Tokyo area. The results not only verify the capability of the RACS system and the effectiveness of the in-vehicle equipment but also indicate the potential of such a beacon based network to improve traffic jam and driving safety whilst providing enhanced communication facilities without increasing radio-wave congestion.

In the twenty-first century, the development of vehicles has been proceeding towards electronics, electric propulsion and system integration in 5 big trends. Environment, Safety, Market Change, Energy Security and Natural Resources. Especially, “Electric Propulsion of Vehicles” is rapidly accelerated for countermeasure of global warming. In this paper, we will propose the current status analysis for automotive high power supply voltage and classification for future view of HEV(Hybird Electric Vehicle). PHEV(Plug-in Hybrid Electric Vehicle) and EV(Electric Vehicle).

In recent years Road Departure Mitigation Systems (RDMS) is introduced to the market for avoiding roadway departure collisions. To support the performance testing of the RDMS, the most commonly seen road edge, grass, is studied in this paper for the development of standard surrogate grass. This paper proposes a method for defining the resembling grass color and height features due to significant variations of grass appearances in different seasons, temperatures and environments. Randomly selected Google Street View images with grass road edges are gathered and analyzed. Image processing techniques are deployed to obtain the grass color distributions. The height of the grass is determined by referencing the gathered images with measured grass heights. The representative colors and heights of grass are derived as the specifications of surrogate grass for the standard evaluation of RDMS.

Vehicles equipped with in-wheel motors are being studied and developed as a type of electric vehicle. Since these motors are attached to the suspension, a large vertical suspension reaction force is generated during driving. Based on this mechanism, this paper describes the development of a method for independently controlling roll and pitch as well as yaw using driving force distribution control at each wheel. It also details the theoretical calculation of a method for decoupling the dynamic motions. Finally, it describes the application of these 3D dynamic motion control methods to a test vehicle and the confirmation of the performance improvement.

This paper investigates a new approach to the quantification technique for road induced vehicle interior noise and vibration within the frequency range up to 40 Hz. By employing the least squares method, both vertical and fore-aft load to each wheel were quantified using transfer function and actual vibration response of the vehicle driven on a road. The coupled structural-acoustic vehicle model using the finite element method, which is also detailed in this paper, is combined with the quantified input load to simulate road induced interior noise and vibration response. Experimental verification, which indicates reasonable accuracy of the simulation, and an application for the prototype development are also presented.

Exhaust and evaporative emissions systems have been developed to match the characteristics and usage of the Toyota THS II plug-in hybrid electric vehicle (PHEV). Based on the commercially available Prius, the Toyota PHEV features an additional external charging function, which allows it to be driven as an electric vehicle (EV) in urban areas, and as an hybrid electric vehicle (HEV) in high-speed/high-load and long-distance driving situations. To reduce exhaust emissions, the conventional catalyst warm up control has been enhanced to achieve emissions performance that satisfies California's Super Ultra Low Emissions Vehicle (SULEV) standards in every state of battery charge. In addition, a heat insulating fuel vapor containment system (FVS) has been developed using a plastic fuel tank based on the assumption that such a system can reduce the diffusion of vapor inside the fuel tank and the release of fuel vapor in to the atmosphere to the maximum possible extent.

Toyota Motor Corporation developed the Fuel Cell Hybrid Vehicle (FCHV). The FCHV-4 is an evolution of the conventional fuel cell vehicle that has made immense improvements in efficiency. Both a fuel cell and a secondary battery are used as sources of energy for the hybrid system. By using these energy sources proportionally, the system can be kept at or near its optimum state. The FCHV-4's system is designed to improve the efficiency and aims for high responsiveness when the vehicle is in a transitional state. In the same way as most electric vehicles, and as in the gasoline powered hybrid “Prius”, the energy the traction motor creates during breaking can be used to regenerate the secondary. The fuel cell and traction motor inverter are connected directly, with the secondary battery connected through the DC/DC converter to the fuel cell in parallel.

Previous reports have already described the details of engine start-shock and the mechanism of vibration mechanism in a stationary vehicle. This vibration can be reduced by optimized engine and motor generator vibration-reduction controls. A prediction method using a full-vehicle MBD model has also been developed and applied in actual vehicle development. This paper describes the outline of a new method for the hybrid system of mechanical power split device with two motors that predicts engine start-shock when the vehicle is accelerating while the engine is stopped. It also describes the results of mechanism analysis and component contribution analysis. This method targets engine start-shock caused by driving torque demand during acceleration after vehicle take-off. The hybrid control system is modeled by MATLAB/Simulink. A power management and motor generator control program used in actual vehicles is installed into the main part of the control system model.

Toyota Hybrid System (THS), that combines a gasoline engine and an electric motor was installed in the Prius, which was introduced in 1997 as the world's first mass-produced hybrid passenger car, and was vastly improved in 2003. The new Prius gained a status of highly innovative and practical vehicle. In 2005, combined with a V6 engine, THS had a further evolution as a Hybrid System for SUV, which was installed in the RX400h and Highlander Hybrid to be introduced into the world. This report will explain “new THS” which achieved both V8 engine power performance and compact class fuel economy, while securing the most stringent emission standard, SULEV.

A new method to measure in-cylinder flame propagation and mixture distribution has been developed. The distribution is derived from analyzing the temporal history of flame spectra of CH* and C2*, which are detected by a spark plug type sensor with multi-optical fibers. The validity of this method was confirmed by verifying that the measurement results corresponded with the results of high speed flame visualization and laser induced fluorescence (LIF) measurement. This method was also applied to analysis of cyclic combustion fluctuation on start-up in a direct injection spark ignition (DISI) engine, and its applicability was confirmed.

In the field of automotive gasoline engines, new products aiming at greater fuel economy and cleaner exhaust gases are under development with the aim of preventing environmental destruction. Severe ignition environments such as lean combustion, stronger charge motion, and large quantities of EGR require ever greater combustion stability. In an effort to meet these requirements, an iridium plug has been developed that achieves high ignitability and long service life through reduction of its diameter, using a highly wear-resistant iridium alloy as the center electrode.(1)(2) Recently, direct injection engines have attracted attention. In stratified combustion, a feature of the direct injection engine, the introduction of rich air-fuel mixtures in the vicinity of the plug ignition region tends to cause carbon fouling. This necessitates plug carbon fouling resistance.

Attaining optimum balance between longitudinal compliance and sideforce compliance steer in a torsion beam suspension system is a challenging task. We developed a suspension in which the longitudinal compliance is almost doubled and the side force compliance steer amount is improved by using the link effect of toe control links. This suspension system has been developed to realize excellent controllability, stability, riding comfort, and road noise performance.

Toyota has been introducing several hybrid vehicles (HV) as a countermeasure to concerns related to the automotive mobility like CO2 reduction, energy security, and emission reduction in urban areas. A next step towards an even more effective solution for these concerns is a plug-in hybrid vehicle (PHV). This vehicle combines the advantages of electric vehicles (EV), which can use clean electric energy, and HV with it's high environmental potential and user-friendliness comparable to conventional vehicles such as a long cruising range. This paper describes a newly developed plug-in hybrid system and its vehicle performance. This system uses a Li-ion battery with high energy density and has an EV-range within usual trip length without sacrificing cabin space. The vehicle achieves a CO2 emission of 59g/km and meets the most stringent emission regulations in the world. The new PHV is a forerunner of the large-scale mass production PHV which will be introduced in a year.

1 A new hybrid transmission (P310) has been developed for FWD 3-liter engine class sports utility vehicles. The development of this transmission has been aimed at improving power performance and fuel economy, achieving the world's top-level weight reduction and compact size, while maintaining high torque capacity. In order to achieve these goals, the gear train and motor have been newly designed, and advanced technology has been applied. Moreover, this hybrid transmission achieves seamless acceleration and quiet performance. This paper describes the major features and performance of this transmission in detail.

Next generation vehicles driven by motor such as electric vehicles and fuel cell vehicles have no engine noise. Therefore the balance of interior noise is different from the vehicles driven by conventional combustion engine. In particular, road induced noise tends to be conspicuous in the low to middle vehicle speed range, therefore, technological development to reduce it is important task. The purpose of this research is to predict the road induced noise from the signals of sensors adopted for automatic driving for utilizing the prediction result as a reference signal to reduce road induced noise by active noise control (ANC). Using the monocular camera which is one of the simplest image sensors, the road induced noise is predicted from the road surface image ahead of the vehicle by machine learning.

A full vehicle multi-body dynamic (MBD) model with suspension control system is developed for fatigue life prediction under rough road condition. The model consists of tires, a trimmed body, heavy attached parts, powertrain, suspension, joints, and a driver model, and includes a suspension control system that varies characteristics of the suspension according to the rough road inputs. For tires, a commercial MBD tire model is employed with identifiable parameters. The models are simulated to run on the optically measured road surface of the proving ground. Apart from the trimmed body, several important heavy attached parts are modeled separately, that represent dynamic behavior that induces complex body input load. These parts, along with suspension and powertrain systems are connected to the body using nonlinear elements such as joints, springs, and dampers. Contact conditions are used to represent mount bushing, hood lock, stopper rubber, etc.