Search Results

To address the need of increasing fuel economy requirements, automotive Original Equipment Manufacturers (OEMs) are increasing the number of turbocharged engines in their powertrain line-ups. The turbine-driven technology uses a forced induction device, which increases engine performance by increasing the density of the air charge being drawn into the cylinder. Denser air allows more fuel to be introduced into the combustion chamber, thus increasing engine performance. During the inlet air compression process, the air is heated to temperatures that can result in pre-ignition resulting and reduced engine functionality. The introduction of the charge air cooler (CAC) is therefore, necessary to extract heat created during the compression process. The present research describes the physics and develops the optimized simulation method that defines the process and gives insight into the development of CACs.

The automotive refrigerant systems can occasionally exhibit a transient hoot/whistle type noise under certain operating conditions. High pressure/velocity refrigerant flow through an evaporator core can readily excite the inherent acoustical and/or structural modes, resulting in audible transient tones. This condition if present can be experienced while driving away from a short stop and can last 2 to 10 seconds. The ambient conditions suitable for creating this noise are - moderate/high air-conditioning (A/C) load during days at 85-95° F temperatures with high humidity. Possible noise generating mechanisms have been discussed in earlier publications and our findings during this study indicate that they are excited by the high velocity superheated refrigerant vapor flow through the evaporator core plates. Examples of this transient noise and its spectral characteristics are presented to characterize this refrigerant system induced issue.

Ultrasonic fatigue tests (testing frequency around 20kHz) have been conducted on A356 aluminum alloys with different copper contents and AS7GU aluminum alloy. Tests were performed in dry air and submerged in water conditions. The effect of copper content was investigated and it was concluded that copper content plays an important role influencing the humidity effect on A356 aluminum alloy ultrasonic fatigue lives. Also, for the same copper content, copper in solute solution or in precipitate have different humidity sensitivities.

The buildup of deposits in EGR coolers causes significant degradation in heat transfer performance, often on the order of 20-30%. Deposits also increase pressure drop across coolers and thus may degrade engine efficiency under some operating conditions. It is unlikely that EGR cooler deposits can be prevented from forming when soot and HC are present. The presence of cooled surfaces will cause thermophoretic soot deposition and condensation of HC and acids. While this can be affected by engine calibration, it probably cannot be eliminated as long as cooled EGR is required for emission control. It is generally felt that “dry fluffy” soot is less likely to cause major fouling than “heavy wet” soot. An oxidation catalyst in the EGR line can remove HC and has been shown to reduce fouling in some applications. The combination of an oxidation catalyst and a wall-flow filter largely eliminates fouling. Various EGR cooler designs affect details of deposit formation.

In this paper, fatigue tests on a cast aluminum alloy (AS7GU-T64) were performed under different frequencies and humidity levels. Tests conducted under conventional frequency in laboratory air have been compared to tests conducted under ultrasonic frequency in dry air, saturated humidity and in distilled water. It was observed that the highest and lowest fatigue lives correspond to ultrasonic fatigue tests in dry air and in distilled water, respectively. Unlike specimens tested at conventional frequency, all of the specimens tested at ultrasonic frequency presented a large amount of slip facets on the fatigue crack propagation fracture surface.

Engine Mapping is usually performed under nominal conditions which include a humidity level of 8 g/Kg. Customers driving at different conditions (which may range from 1 g/Kg in colder and dry climates and up to 35 g/Kg as in tropical climates) may experience less-than-optimal engine combustion which results in reduced onroad fuel economy. Humidity has an EGR-equivalent effect, and measuring it will correct the spark timing, mainly at Maximum Brake Torque (MBT) and borderline conditions, and claim back some of those losses. This paper aims at quantifying the small fuel economy benefits associated with on-board humidity measurement for certain customer use cases at high humidity conditions. Dyno data was collected for a Ford 2.3L GTDI engine at three speed load points, and intake air humidity was varied between 20% and 80% relative humidity. The effect of humidity compensation on spark timing, combustion phasing, knock, and consequently on overall engine efficiency was analyzed.

Engine Mapping is usually performed under nominal conditions which include a humidity level of 8 g/Kg. Customers driving at different humidity conditions (which may range from 1 g/Kg in dry and colder climates and up to 35 g/Kg as in tropical climates) may experience a degraded performance due to the errors in engine torque estimation provided by the ECU. The torque estimation error interacts with many other features that affect drivability, such as the peak performance of the engine, transmission shift quality, etc. This paper extends the investigation in Part-1 by analyzing and quantifying the torque estimation error that may result in certain customer use cases at high humidity conditions, due to the mismatch between calibrated and actual conditions. The analysis is mainly performed for Speed-Density systems (MAP sensor based) but the effect of mass air flow sensor (MAF sensor) based systems is also briefly considered.

Corrosion failures of aluminum air conditioner evaporator cores have been reported in regions where the climate is relatively warm and humid. Microbiologically-influenced corrosion [MIC] has been implicated in these failures. Application of surface-treatment chemicals may inhibit microbiological (bacterial) growth and/or attachment, thereby reducing the potential for MIC. In this study, two laboratory methods were developed to evaluate selected surface-treatment chemicals for their ability to inhibit bacterial growth and reduce bacterial attachment to treated surfaces. Using the developed methods, two controlled-atmosphere brazed aluminum core materials and three surface-treatment chemicals were evaluated. Neither of the untreated core materials was found to inhibit the growth of the bacteria tested.

Collection of diesel exhaust using the Tapered Element Oscillating Microbalance (TEOM) instrument was investigated as an alternative to the traditional method of filter weighing for particulate matter mass determination. Such an approach, if successful, would eliminate considerable manual labor involved in weighing, as well as the delay of hours or days before final results were known. To avoid known artifacts in the second-by-second mode of operation, the TEOM was used in a phase-by-phase mode and was equilibrated with air of constant temperature and humidity before each measurement. Electrically operated valves were used to automate the equilibration and measurement process. The study also included a comparison between two types of TEOM filter - an older type and a new one designed by the TEOM manufacturer for more uniform flow and less flexing. Best results were obtained with the TEOM using the new filter under no-flow conditions.

In automotive assembly facilities worldwide, many critical vehicle systems such as brakes, power steering, radiator, and air conditioning require the appropriate fluid to function. In order to insure that these critical vehicle systems receive the correct amount of properly treated fluid, automotive manufacturers employ a method called Evacuation and Fill. Due to their closed-loop design, many critical vehicle systems must be first exposed to vacuum prior to being flooded with fluid. Only after the evacuation and fill process is complete will the critical vehicle system be able to perform as specified. It has long been thought, but never proven, that humidity and entrenched fluid were major hindrances to the Evacuation and Fill process. Consequently, Ford Motor Company Advanced Manufacturing Technology Development, Sandalwood Enterprises, Kettering University, and Dominion Tool & Die conducted a detailed project on this subject.