Search Results

For optimum efficiency, the direct injection (DI) gasoline engine requires two operating modes to cover the full load/speed map. For lower loads and speeds, stratified charge operation can be used, while homogeneous charge is required for high loads and speeds. This paper has focused its attention on the latter of these modes, where the performance is highly dependent on the quality of the fuel spray, evaporation and the air-fuel mixture preparation. Results of quantitative and qualitative Laser Induced Fluorescence (LIF) measurements are presented, together with shadow-graph spray imaging, made within an optically accessed DI gasoline engine. These are compared with previously acquired air flow measurements, at various injection timings, and with engine performance and emissions data obtained in a fired single cylinder non-optical engine, having an identical cylinder head and piston crown geometry.

Two optical techniques together with a CFD simulation have been used to study the interaction of intake airflow with the injected fuel spray in a motored direct injection gasoline engine. The combustion chamber was of a pent-roof construction with the side-mounted injector located low down between the inlet valves injecting at a 54° angle to the cylinder axis. The two-dimensional piston bowl shape allowed optical access for the Mie scatter technique to be used to investigate the liquid fuel behaviour in the central axial plane of the cylinder lying midway between the two inlet valves and passing through the centre line of the injector nozzle. A second set of images was obtained using backlighting, this time looking through the glass cylinder liner directly towards the injector. The in-cylinder simulation was run using the VECTIS software. Measurements and simulations were conducted for a range of early SOI timings between 20° and 80° ATDC.

The pursuit of flexibility is a recurring theme in engine design and development. Engines that are able to switch between the two-stroke operating cycle and four-stroke operation promise a great leap in flexibility. Such 2S-4S engines could then continuously select the optimum operating mode - including HCCI/CAI combustion - for fuel efficiency, emissions or specific output. With recent developments in valvetrain technology, advanced boosting devices, direct fuel injection and engine control, the 2S-4S engine is an increasingly real prospect. The authors have undertaken a comprehensive feasibility study for 2S-4S gasoline engines. This study has encompassed concept and detailed design, design analysis, one-dimensional gas dynamics simulation, three-dimensional computational fluid dynamics, and vehicle simulation. The resulting 2/4SIGHT concept engine is a 1.04 l in-line three-cylinder engine producing 230 Nm and 85 kW.

The research presented here aims at providing a deeper understanding of the formation of nitric oxide in diesel combustion. To this end, in-cylinder distributions of nitric oxide (NO) were acquired by laser-induced fluorescence (LIF) in a rapid compression machine at conditions representative of a modern diesel passenger vehicle. In particular, the effects of injection and in-cylinder pressure on NO formation were investigated temporally and spatially to offer new insight into the formation of NO. Excitation and collection strategies were notably fine-tuned to avoid the collection of spurious signal due to oxygen (O₂) fluorescence. NO fluorescence was first recorded slightly after the onset of the diffusion flame and until late in the expansion stroke. The early low levels of NO were located on the lean side of the high density of hydroxyl radicals (OH).

Rail pressures of modern diesel fuel injection systems have increased significantly over recent years, greatly improving atomisation of the main fuel injection event and air utilisation of the combustion process. Continued improvement in controlling the process of introducing fuel into the cylinder has led to focussing on fluid phenomena related to transient response. High-speed microscopy has been employed to visualise the detailed fluid dynamics around the near nozzle region of an automotive diesel fuel injector, during the opening, closing and post injection events. Complementary computational fluid dynamic (CFD) simulations have been undertaken to elucidate the interaction of the liquid and gas phases during these highly transient events, including an assessment of close-coupled injections.

The influences of injector nozzle geometry, injection pressure and ambient air conditions on a diesel fuel spray were examined using back-lighting techniques. Both stills and high speed imaging techniques were used. Operating conditions representative of a modern turbocharged aftercooled HSDI diesel engine were achieved in an optical rapid compression machine fitted with a common rail fuel injector. Qualitative differences in spray structure were observed between tests performed with short and long injection periods. Changes in the flow structure within the nozzle could be the source of this effect. The temporal liquid penetration lengths were derived from the high-speed images. Comparisons were made between different nozzle geometries and different injection pressures. Differences were observed between VCO (Valve Covers Orifice) and mini-sac nozzles, with the mini-sac nozzles showing a higher rate of penetration under the same conditions.

An experimental study of the mixture response performance of novel, port-fuel injection strategies upon combustion stability in a gasoline engine was undertaken at low engine load and speed conditions in the range of 1.0 bar to 1.8 bar GIMEP and 1000 rpm to 1800 rpm. The aim was to improve the thermal efficiency of the engine, by extending the lean limit of combustion stability, through promotion of stable charge stratification. The investigation was carried out using a modified 4-valve single-cylinder head, derived from a 4-cylinder, pent-roof, production, gasoline engine. The cylinder head was modified by dividing the intake tract into two, separate and isolated passages; each incorporating a production fuel injector. The fuel injection timing and duration were controlled independently for each injector.

The conventional Diesel cycles engine is now approaching the practical limits of efficiency. The recuperated split cycle engine is an alternative cycle with the potential to achieve higher efficiencies than could be achieved using a conventional engine cycle. In a split cycle engine, the compression and combustion strokes are performed in separate chambers. This enables direct cooling of the compression cylinder reducing compression work, intra cycle heat recovery and low heat rejection expansion. Previously reported analysis has shown that brake efficiencies approaching 60% are attainable, representing a 33% improvement over current advanced heavy duty diesel engine. However, the achievement of complete, stable, compression ignited combustion has remained elusive to date.

A system for stratifying recycled exhaust gas (EGR) to substantially increase dilution tolerance has been applied to a port injected four-valve gasoline engine. This system, known as Combustion Control through Vortex Stratification (CCVS), has shown greatly improved fuel consumption at a stoichiometric air/fuel ratio. Both burnrate (10-90% burn angle) and HC emissions are almost completely insensitive to EGR up to best economy EGR rate. Cycle to cycle combustion variation is also excellent with a coefficient of variation of IMEP of less than 2% at best economy EGR rate. This paper describes a research programme aimed at gaining a better understanding of the in-cylinder processes in this combustion system.

For efficiency, the majority of modern diesel engines implement multiple injection strategies, increasing the frequency of transient injection phases and thus, end of injection (EOI) events. Recent advances in diagnostic techniques have identified several EOI phenomena pertinent to nozzle surface wetting as a precursor for deposit formation and a potential contributor towards pollutant emissions. To investigate the underlying processes, highspeed optical measurements at the microscopic scale were performed inside a motored diesel engine under low load/idling conditions. Visualisation of the injector nozzle surface and near nozzle region permitted an indepth analysis of the post-injection phenomena and the behaviour of fuel films on the nozzle surface when the engine is not fired. Inspection of the high-speed video data enabled an interpretation of the fluid dynamics leading to surface wetting, elucidating the mechanisms of deposition and spreading.