Search Results

New concepts in oxygen enrichment of the inlet air have been examined in tests on two direct injection diesel engines, showing: significant reduction in particulate emissions (nearly 80% at full load), increased thermal efficiency if injection timing control is employed, substantial reductions in exhaust smoke under most conditions, ability to burn inferior quality fuels which is economically very attractive and achivement of turbo-charged levels of output with consequential benefits of increased power/mass and improved thermal efficiency. The replacement of an engine's turbocharger and intercooling system with a smaller turbocharger and polymeric membrane elements to supply the oxygen enriched stream should allow improved transient response. NOx emission remain a problem and can only be reduced to normally aspirated engine levels at some efficiency penalty.

This paper presents a technical and financial analysis of several, potentially near-zero greenhouse gas emission passenger vehicles for Australian driving conditions. Conventional, series hybrid, plug-in hybrid (PHEV) and fully electric (BEV) vehicles of class B and class E sizes are considered, with their propulsive energy assumed to originate from a source that is free of net greenhouse gas emissions. Extensions to the vehicle models developed by the authors in our previous works [1, 2, 3] are first developed. These enable estimation of the size of each major component in each powertrain, and therefore the total, in-service energy consumption and in-service greenhouse gas emissions. The component sizing also allows estimation of the each vehicle's purchase price, its embodied energy and its embodied greenhouse gas emissions, the latter assuming scenarios for both the current and a future, low emission intensity of Australian manufacturing.

The 2023 FISITA White Paper (for which the author was a contributor) on managing in-service emissions and transportation options, to reduce CO2 (CO2-e or carbon footprint) from the existing vehicle fleet, proposed 6 levers which could be activated to complement the rapid transition to vehicles using only renewable energy sources. Another management opportunity reported here is optimizing the vehicle’s life in-service to minimize the life-cycle CO2 impact of a range of present and upcoming vehicles. This study of the US vehicle fleet has quite different travel and composition characteristics to European (EU27) vehicles. In addition, the embodied CO2 is based on ANL’s GREET data rather than EU27 SimaPro methodology. It is demonstrated that in-service, whole-of-life mileage has a significant influence on the optimum life cycle CO2 for BEVs and H2 fuelled FCEVs, as well as ICEs and PHEVs.

This paper studies autoignition characteristics and HCCI engine combustion of ketone fuels, which are important constituents of recently discovered fungi-derived biofuels. Two ketone compounds, 2,4-dimethyl-3-pentanone (DMPN) and cyclopentanone (CPN), are systematically investigated in the Sandia HCCI engine, and the results are compared with conventional gasoline and neat ethanol. It is found that CPN has the lowest autoignition reactivity of all the biofuels and gasoline blends tested in this HCCI engine. The combustion timing of CPN is also the most sensitive to intake-temperature (Tin) variations, and it is almost insensitive to intake-pressure (Pin) variations. These characteristics and the overall HCCI performance of CPN are similar to those of ethanol. In contrast, DMPN shows multi-faceted autoignition characteristics. On the one hand, DMPN has strong temperature-sensitivity, even at boosted Pin, which is similar to the low-reactivity ethanol and CPN.

This paper compares the performance, efficiency, emissions and combustion parameters of a prototype two cylinder 430 cm3 engine which has been tested in a variety of normally aspirated (NA) modes with compression ratio (CR) variations. Experiments were completed using 98-RON pump gasoline with modes defined by alterations to the induction system, which included carburetion and port fuel injection (PFI). The results from this paper provide some insight into the CR effects for small NA spark ignition (SI) engines. This information provides future direction for the development of smaller engines as engine downsizing grows in popularity due to rising oil prices and recent carbon dioxide (CO2) emission regulations. Results are displayed in the engine speed, manifold absolute pressure (MAP) and CR domains, with engine speeds exceeding 10000 rev/min and CRs ranging from 9 to 13. Combustion analysis is also included, allowing mass fraction burn (MFB) comparison.

Direct Injection (DI) is believed to be one of the key strategies for maximizing the thermal efficiency of Spark Ignition (SI) engines and meet the ever-tightening emissions regulations. This paper explores the use of Liquefied Petroleum Gas (LPG) liquid phase fuel in a 1.5 liter SI four cylinder gasoline engine with double over head camshafts, four valves per cylinder, and centrally located DI injector. The DI injector is a high pressure, fast actuating injector enabling precise multiple injections of the finely atomized fuel sprays. With DI technology, the injection timing can be set to avoid fuel bypassing the engine during valve overlap into the exhaust system prior to combustion. The fuel vaporization associated with DI reduces combustion chamber and charge temperatures, thereby reducing the tendency for knocking. Fuel atomization quality supports an efficient combustion process.

The hydrogen assisted jet ignition system (HAJI) replaces the spark plug of an Otto cycle engine and consists of a very small pre-chamber into which a hydrogen injector and spark plug are installed. The HAJI system allows stable combustion of very lean main-chamber hydrocarbon mixtures, leading to improved thermal efficiency and very much reduced NOx emissions. The current investigation focuses on the application of HAJI to a modern pent-roof, four valve per cylinder automotive engine. The development of a new hydrogen injection system and HAJI pre-chamber based on proprietary gasoline and diesel injectors is described. Results from injector and engine performance testing are presented in detail.

Diesel engines are used in heavy duty applications because of their high efficiency and reliability. However, their high diesel particulates and NOx emissions remain major concerns. An eight cylinder direct injection diesel engine was connected to a partial flow particulate sampling mini-dilution tunnel. Six different grades of diesel fuels were studied for their regular emissions as well as smoke and particulate emissions. Each fuel was tested at three engine speeds and full load. This paper presents the results of these tests which includes analysis of the effects of load, cetane number, 90% distillation temperature, and density for steady state conditions. A correlation was developed for converting smoke numbers in Hartridge Smoke Units (HSU) to the specific particulate emissions by evaluating results of all fuels tests. Another correlation was also developed for diesel particulates and NOx emissions trade-off.

Exhaust emission tests were performed on a fleet of vehicles comprising a range of engine technology from leaded fuel control methods to closed loop three-way catalyst meeting 1992 U.S. standards but marketed in Australia. Each vehicle was tested to 5 different driving cycles including the FTP cycles and steady speed driving. Research had shown that for hot-start operation the major driving pattern parameters which influence fuel consumption and exhaust emissions are average speed and PKE (the positive acceleration kinetic energy per unit distance). Plots from analysis of micro-trip fuel use and emissions rates from the test cycles may be presented as contours in PKE. It follows that the micro trip emissions from a range of driving cycles including, regulated e.g. FTP city and unregulated e.g. LA-92, recently developed EPA cycles or from other cities e.g. Bangkok can be superimposed.

A fleet of 17 utility, van and flat tray bodied trucks has been tested for fuel consumption and exhaust emissions over a range of drive cycles and steady state operating conditions. The influence of vehicle load on the results was included. For each vehicle the tractive force applied by the chassis dynamometer, on which testing was performed, was adjusted to match those found on the road using a new procedure. The fuel consumption results show a downward trend with model year (1.7% annum); about 30% higher petrol use compared with diesel; a cold start penalty of 3 L/100 km and over 2:1 variation for vehicles capable of identical transport task. Exhaust emissions from these rigid trucks were between 3 and 6 times greater than those of the passenger car fleet.

In this paper the experimental performance of the lean limits is examined for two different types of engines the first a dedicated LPG high compression ratio 2-valve per cylinder engine (Ford of Australia MY 2001 AU Falcon) and the second a gasoline moderate compression 4-valve per cylinder variant of the same engine (Ford of Australia MY 2006 BF Falcon). The in-cylinder composition at the lean limit over a range of steady state operating conditions is estimated using a quasi-dimensional model. This makes it possible to take into account the effects of both residual fraction and fresh charge diluents (EGR and excess air) that allow the exploration of a modeled lean limit performance [1, 2]. The results are compared to the predictions from a model for combustion variability applied to the quasi-dimensional model operating in optimization mode.

Oxygen-enriched air supplied to a diesel engine has significant benefits in reducing the particulate emissions of all fuels tested. A Caterpillar 3208 direct injection diesel engine was modified to operate on a wide range of fuel grades including residual fuel oils with oxygen-enriched intake air. The paper focuses on four fuels, two fuels were regular automotive distillate fuels, the third was a low emission diesel fuel and the fourth fuel had high boiling point fractions. Comparison with less extensive work on residual fuel oil is also included. Smoke and particulates decrease by up to 94% at full load with 27% oxygen concentration. Performance with oxygen addition using regular fuels showed comparable smoke and particulates to a premium priced low emission fuel used specifically in underground mines.

The HAJI (Hydrogen Assisted Jet Ignition) system for S.I. engines utilises direct injection of small amounts of hydrogen to enhance the combustion of a variety of automotive fuels. Although not the primary purpose of HAJI, the hardware, once in place, also lends itself to the possibility of hydrogen-only running during a cold start. Cold-start simulations have been performed using a single cylinder engine. Results are presented, comparing hydrogen-only tests with standard HAJI operation and normal spark-ignition operation. HAJI and spark ignition tests were carried out with gasoline as the main-chamber fuel. Emission levels and combustion stability characteristics were recorded as the engine warmed up. The differences between the various fueling/ignition scenarios are presented and the implications for possible automotive applications are discussed in light of current and proposed emissions legislation.

Hydrogen Assisted Jet Ignition (HAJI) is a novel method of maintaining combustion stability during ultra-lean operation of conventional, homogeneously charged, SI engines. When operating with HAJI above λ=2, CO and NOx emissions fall to low levels while HC emissions rise to approximately double their stoichiometric value. HC emissions were investigated by operating a HAJI equipped, optically accessible, four-valve single cylinder engine at 600 r/min, wide open throttle (WOT), and from λ=1 to λ=2.4. A fast flame ionisation detector was used to collect real time hydrocarbon concentration data from behind one of the exhaust valves, inside the HAJI pre-chamber, and from near the combustion chamber wall. Flame images were also obtained. Exhaust port sampling shows that the HC concentration during blowdown and early exhaust is increased, but the concentration at the end of exhaust is decreased.

The goal of hydrogen engine research is to achieve highest possible efficiency with low NOx emissions. This is necessary for the hydrogen car to remain competitive with the ever-improving efficiency of conventional fuel's use, to take advantage of the increased availability of hydrogen distribution for fuel cells and to achieve better range than battery electric vehicles. This paper examines the special problems of hydrogen engine combustion and ways to improve efficiency. Central to this are the effects of compression ratio (CR) and lambda (excess air ratio) and ignition system. The results demonstrate highest indicated thermal efficiency at ultra lean condition of lambda ≻ 2 and with central ignition. This need for this lean mixture is partly explained by the higher heat transfer losses.

A fast flame ionisation detector (FID) is able to measure the hydrocarbon (HC) concentration at a single point in the exhaust port. However, when sampling is conducted near the plane of the exhaust valve, these measurements are not representative of the entire port cross-section. This paper describes a multi-point extension to a standard fast FID probe, enabling the instantaneous measurement of a more representative HC concentration near the plane of the exhaust valve. Construction and use of the multi-point probe is discussed, and results are compared with standard single-point measurements.

The challenge of tough fuel consumption reduction targets and near zero NOx emission standards can be met by optimization of the full range of engine design variables. Here these are explored through an engine simulation model and the application of an optimizing algorithm that can work in discontinuous data space. The combustion model has main features that include flame propagation, the effects of turbulence, chamber shape interaction and NOx formation. Two engine configurations are used to illustrate the application of the model and optimizer. Both allow the adoption of extra lean burn possible with LPG as fuel and EGR through an external route or cam phasing. In the first the compression ratio and cam profiles are fixed, in the second study they are also optimized.

This paper presents a study of the performance of a lean burn, natural gas-fuelled, naturally aspirated, spark ignition engine for an E class vehicle. Engine performance and exhaust emissions (NO, CO, and UHC) data are first discussed. An energy balance of the engine operating at different loads and air-fuel ratios is then presented, and used to explain why engine efficiency varies with air-fuel ratio. Finally, the hot start drive cycle CO2e (CO2 equivalent) emissions are estimated for a vehicle with this engine. This shows a potential for significant reduction in vehicle greenhouse gas emissions compared to an equivalent gasoline-fuelled vehicle.

This paper presents a parametric, experimental study of the performance of gas and liquid propane injection in a spark ignition, multi-point port injected (MPI) engine. An inline, six cylinder engine is used over a wide range of speeds and torques, and the air/fuel ratio, compression ratio and injection timing are all varied. The engine was mapped at the standard compression ratio of 9.65:1 with the original, gasoline MPI system, propane gas MPI, and single point, throttle body, propane gas injection. Gas and liquid propane MPI are then tested at a compression ratio of 11.7:1. Contour plots of thermodynamic efficiency and the specific emissions of HC, NOx, CO2 and CO over the torque/speed range are presented and compared. The results show significant differences in performance between gas and liquid propane MPI injection, as well as the MPI and throttle body gas injection.

This paper presents a numerical study of trace knocking combustion of ethanol/gasoline blends in a modern, single cylinder SI engine. Results are compared to experimental data from a prior, published work [1]. The engine is modeled using GT-Power and a two-zone combustion model containing detailed kinetic models. The two zone model uses a gasoline surrogate model [2] combined with a sub-model for nitric oxide (NO) [3] to simulate end-gas autoignition. Upstream, pre-vaporized fuel injection (UFI) and direct injection (DI) are modeled and compared to characterize ethanol's low autoignition reactivity and high charge cooling effects. Three ethanol/gasoline blends are studied: E0, E20, and E50. The modeled and experimental results demonstrate some systematic differences in the spark timing for trace knock across all three fuels, but the relative trends with engine load and ethanol content are consistent. Possible reasons causing the differences are discussed.