Search Results

The dust holding capacity of air cleaning filter depends on the size distribution of the particles. Traditional test dusts like Arizona road dust consist of a single mode of coarse particles. The purpose of this study is to evaluate the dust holding capacities of air filters with a bi-modal test dust that simulates the dust in atmospheric environments. The fine mode of the test dust consists of submicron Alumina particles that represent the fine particles in atmosphere. The coarse mode consists of traditional AC fine dust. The fine and coarse dusts are mixed in different mass ratios to simulate different atmospheric conditions. The ratios are 100% fine, 50%/50%, 25%/75%, 10%/90%, and 100% coarse. An engine air filter and a HVAC filter were studied with the bi-modal test dusts. The filter pressure drops were measured as a function of the dust loading. The results show that the flow resistance rises significantly faster as the ratio of fine to coarse fraction increases.

A system was designed for controlling fuel injection and ignition timing for use on a port fuel injected, gas-fueled engine. Inputs required for the system include manifold absolute pressure, manifold air temperature, a once per revolution crankshaft pulse, a once per cycle camshaft pulse, and a relative encoder pulse train to determine crank angle. A prototype card installed in the computer contains counters and discrete logic which control the timing of ignition and injection events. High current drivers used to control the fuel injector solenoids and coil primary current are optically isolated from the computer by the use of fiber optic cables. The programming is done in QuickBASIC running in real time on a 25 MHz 80486 personal computer. The system was used to control a gas-fueled spark ignition engine at various conditions to map the torque versus air-fuel ratio and ignition timing. Each surface was mapped for a given fuel flow and speed.

This paper summarizes the state-of-the-art of various alternative fuel technologies for heavy-duty transit applications and compares them to conventional and “ clean” diesel engines. Alternative powerplants considered include compressed natural gas (CNG), liquefied natural gas (LNG), methanol, ethanol, liquefied petroleum gas (LPG), hydrogen, and several electric technologies. The various technologies are ranked according to emissions, operating and capital costs, safety, development status, driveability, and long term fuel supply. A simple spreadsheet-based rating system is presented; it not only provides a versatile, semi-quantitative way to rank technologies using both quantitative and qualitative information, but also helps identify critical areas which limit implementation for a given application. An example is given for urban transit buses.

In many operating regimes, exhaust gas recirculation (EGR) while maintaining MBT spark timing improves cycle efficiency in SI engines. As the level of exhaust dilution is increased, the flame speed is reduced and the combustion rate is impaired. This leads to a drop in fuel economy as EGR rates are increased beyond the optimal level. To take advantage of the efficiency benefit of EGR without incurring the penalties of late combustion, a sensor which detects late combustion is tested. The signal from an ionization sensor placed near the exhaust port has been found to correlate to combustion which continues late into the expansion stroke. It may be possible to use the output from the ion sensor to maintain the EGR at the the optimum for fuel economy.

Combustion characteristics of an L-head engine combustion chamber have been examined using ionization probes and piezioelectric pressure transducers. The method describes how pressure rise rates, peak pressures, mean effective pressures, and flame arrival times were recorded. The flame arrival times were then used to find the position and shape of the flame front as a function of time. The influence of spark plug location on the above parameters was then examined for two different combustion chamber shapes.

Psychological, group interaction, and task performance characteristics were evaluated in four polar expedition teams varying in national and gender composition. Leaders played a crucial role in promoting strong group cohesiveness and morale. North American members were more highly focused on achievement strivings, Russians on avoidance of failure. Gender differences in behavior were also evident. An all women's team demonstrated a high level of cooperativeness and social support of other team members. Across teams, anxiety, tension, and health concerns increased in the early stages of the expedition and decreased significantly at later stages. The overall findings indicate the need to focus on the interaction of personality, cultural, gender, and task performance demands in personnel selection and during long duration missions. Implications for the optimal design of space vehicles and habitats are discussed.

Cruise control is one of the most critical issues that manufacturers concern about. But last many researches just focused on engine side control with general step transmission. Continuously Variable Transmissions (CVT) can cover a wide range of ratios continuously. This makes it possible to operate a combustion engine in more efficient working points than stepped transmission. With this merit, fuel optimal cruise control by CVT ratio control is possible with precise longitudinal dynamic model. Estimation of longitudinal load such as road slope and rolling resistance is essential for precise cruise control of automotive vehicle. In this paper, using model based road slope estimation method with gravity sensor, precise longitudinal dynamic model of automotive vehicle is presented. Real-time adaptive algorithm is also implemented for detecting external driving condition change and compensating bias of g-sensor.

Exhaust particulate emissions from a 4-cylinder, 2.25 liter spark ignition engine were measured and characterized. A single-stage ejector-diluter system was used to dilute and cool the exhaust sample for measurement. The particulate measurement equipment included a condensation nucleus counter and a scanning mobility particle sizer. Exhaust measurements were made both upstream and downstream of the catalytic converter using three different fuels. Unlike particulate emissions in diesel engines, spark ignition exhaust particle emissions were found to be highly unstable. Typically, a stable “baseline” concentration on the order of 105 particles/cm3 is emitted. Occasionally, however, a “spike” in the exhaust particle concentration is observed. The exhaust particle concentrations observed during these spikes can increase by as much as two orders of magnitude over the baseline concentration.

Combustion aerosols consist mainly of elemental and organic carbon (EC and OC). Since EC strongly absorbs light and thus affects atmospheric visibility and radiation balance, there is great interest in its measurement. To this end, the National Institute for Occupational Safety and Health (NIOSH) published a standard method to determine the mass of EC and OC on filter samples. Another common method of measuring carbon in aerosols is the aethalometer, which uses light extinction to measure “black carbon” or BC, which is considered to approximate EC. A third method sometimes used for estimating carbon in submicron combustion aerosols, is to measure particle size distributions using a scanning mobility particle sizer (SMPS) and calculate mass using the assumptions that the particles are spherical, carbonaceous and of known density.

Partially premixed low temperature combustion (LTC) in diesel engines is a strategy for reducing soot and NOX formation, though it is accompanied by higher unburned hydrocarbon (UHC) emissions compared to conventional mixing-controlled diesel combustion. In this work, two independent methods of quantifying light UHC species from a diesel engine operating in early LTC (ELTC) modes were compared: Fourier transform infrared (FT-IR) spectroscopy and gas chromatography-mass spectroscopy (GC-MS). A sampling system was designed to capture and transfer exhaust samples for off-line GC-MS analysis, while the FT-IR sampled and quantified engine exhaust in real time. Three different ELTC modes with varying levels of exhaust gas recirculation (EGR) were implemented on a modern light-duty diesel engine. GC-MS and FT-IR concentrations were within 10 % for C2H2, C2H4, C2H6, and C2H4O. While C3H8 was identified and quantified by the FT-IR, it was not detected by the GCMS.

The correlations between the physical properties and autoignition parameters of several alternate fuels have been examined. The fuels are DF-2 and its blends with petroleum derived fuels, coal derived fuels, shale derived fuels, high aromatic naphtha sun-flower oils, methanol and ethanol. A total of eighteen existing correlations are discussed. An emphasis is made on the suitability of each of the correlations for the development of electronic controls for diesel engines when run on alternate fuels. A new correlation has been developed between the cetane number of the fuels and its kinematic viscosity and specific gravity.

Extended range electric vehicles (EREVs) are a potential solution for fossil fuel usage mitigation and on-road emissions reduction. The use of EREVs can be shown to yield significant fuel economy improvements when proper energy management strategies (EMSs) are employed. However, many in-use EREVs achieve only moderate fuel reduction compared to conventional vehicles due to the fact that their EMS is far from optimal. This paper focuses on in-use rule-based EMSs to improve the fuel efficiency of EREV last-mile delivery vehicles equipped with two-way Vehicle-to-Could (V2C) connectivity. The method uses previous vehicle data collected on actual delivery routes and machine learning methods to improve the fuel economy of future routes. The paper first introduces the main challenges of the project, such as inherent uncertainty in human driver behavior and in the roadway environment. Then, the framework of our practical physics-model guided data-driven approach is introduced.

A key challenge for the practical introduction of dual-fuel reactivity controlled compression ignition (RCCI) combustion modes in diesel engines is the requirement to store two fuels on-board. This work demonstrates that partially reforming diesel fuel into less reactive products is a promising method to allow RCCI to be implemented with a single stored fuel. Experiments were conducted using a thermally integrated reforming reactor in a reformed exhaust gas recirculation (R-EGR) configuration to achieve RCCI combustion using a light-duty diesel engine. The engine was operated at a low engine load and two reformed fuel percentages over ranges of exhaust gas recirculation (EGR) rate and main diesel fuel injection timing. Results show that RCCI-like emissions of NOx and soot were achieved load using the R-EGR configuration. It was also shown that complete fuel conversion in the reforming reactor is not necessary to achieve sufficiently low fuel reactivity for RCCI combustion.

Exhaust particle number concentrations and size distributions were measured from the exhaust of a 1995 direct injection, Diesel engine. Number concentrations ranged from 1 to 7.5×107 particles/cm3. The number size distributions were bimodal and log-normal in form with a nuclei mode in the 7-15 nm diameter range and an accumulation mode in the 30-40 nm range. For nearly all operating conditions, more than 50% of the particle number, but less than 1% of the particle mass were found in the nuclei mode. Preliminary indications are that the nuclei mode particles are solid and formed from volatilization and subsequent nucleation of metallic ash from lubricating oil additives. Modern low emission engines produce low concentrations of soot agglomerates. The absence of these agglomerates to act as sites for adsorption or condensation of volatile materials makes nucleation and high number emissions more likely.

Particle concentrations and size distributions were measured in the exhaust of a turbocharged, aftercooled, direct-injection, Diesel engine equipped with a ceramic filter (trap). Measurements were performed both upstream and downstream of the filter using a two-stage, variable residence time, micro-dilution system, a condensation particle counter and a scanning mobility particle sizer set up to count and size particles in the 7-320 nm diameter range. Engine operating conditions of the ISO 11 Mode test were used. The engine out (upstream of filter) size distribution has a bimodal, log normal structure, consisting of a nuclei mode with a geometric number mean diameter, DGN, in the 10-30 nm range and an accumulation mode with DGN in the 50-80 nm range. The modal structure of the size distribution is less distinct downstream of the filter. Nearly all the particle number emissions come from the nuclei mode, are nanoparticles (Dp < 50nm), and are volatile.

The purpose of this study is to compare the dust loading behavior of ten filter media. The filters are used in engine air filtration, self-cleaning industrial air cleaners, building heating ventilation and cooling (HVAC), automotive cabin air filtration, air respirators, and general purpose air cleaning. Several types of filter media are tested. The filters include cellulose, synthetic (felt), glass, dual-layered glass/cellulose, mixed synthetic/glass, gradient packing glass, and electrically charged fibers. The initial pressure drops and fractional collection efficiencies as a function of particle size are reported. The filters were evaluated with two test dusts to investigate the size-dependent dust loading behavior. The two test dusts are SAE fine and submicron alumina powder (median diameter 0.25 μm). The results are analyzed and compared. It was found that the cellulose filters exhibited surface loading behavior and have the fastest growth of pressure drops.

Alcohols are examined as supplemental carbureted fuels for highspeed turbocharged diesels as typified by the White Motor/Waukesha F310 DBLT (6 cylinder, 310 cu. in.). Most of the work was with methanol; ethanol and isopropanol were compared at a few points. Fumigation (dual-fueling) with alcohol significantly reduced smoke and intake manifold temperature. These effects were largest at high load. Efficiency and HC emissions were essentially unchanged. Cylinder pressures and rise rates were examined for possible adverse effects on engine structure. The range of speed and load favorable to alcohol dual-fueling are such that, should alcohols become economically competitive as fuels, a practical duel-fuel system could be applied to existing diesel engines.

The impact of compression ratio on engine efficiency is well known. A plethora of mechanical concepts have been proposed for altering engine compression ratio in real time. Some of these, like free-piston configurations or complex crank-slider mechanisms have the added ability to alter piston trajectory along with compression ratio. This secondary modality raises the question: Is there a more optimal piston position versus crank-angle profile for spark-ignition (SI) engines than the near-sinusoidal motion produced by a traditional four-bar crank-slider mechanism? Very little published literature directly addresses this question. This work presents the results of a quasi-dimensional SI engine model using piston trajectory as an input. Specific trajectory traits including increased dwell at top dead center and asymmetric compression and expansion strokes were swept. The trajectory also was optimized using a single objective genetic algorithm with 60 individuals and 40 generations.

As part of an ongoing program to control the emissions of diesel-powered equipment used in underground mines, the U. S. Bureau of Mines evaluated exhaust emissions from a compression ignition engine using oxygenated diesel fuels and a diesel oxidation catalyst (DOC). The fuels include neat (100%) soy methyl ester (SME), and a blend of 30% SME (by volume) with 70% petroleum diesel fuel. A Caterpillar 3304 PCNA engine was tested for approximately 50 hours on each fuel. Compared with commercial low-sulfur diesel fuel (D2), neat SME increased volatile organic diesel particulate matter (DPM) but greatly decreased non-volatile DPM, for a net decrease in total DPM. The DOC further reduced volatile and total DPM NOx emissions were slightly reduced for the case of neat SME, but otherwise were not significantly affected. Peak brake power decreased 9% and brake specific fuel consumption increased 13 to 14% for the neat methyl soyate because of its lower energy content compared with D2.

In-cylinder reforming of injected fuel during an auxiliary negative valve overlap (NVO) period can be used to optimize main-cycle auto-ignition phasing for low-load Low-Temperature Gasoline Combustion (LTGC), where highly dilute mixtures can lead to poor combustion stability. When mixed with fresh intake charge and fuel, these reformate streams can alter overall charge reactivity characteristics. The central issue remains large parasitic heat losses from the retention and compression of hot exhaust gases along with modest pumping losses that result from mixing hot NVO-period gases with the cooler intake charge. Accurate determination of total cycle energy utilization is complicated by the fact that NVO-period retained fuel energy is consumed during the subsequent main combustion period. For the present study, a full-cycle energy analysis was performed for a single-cylinder research engine undergoing LTGC with varying NVO auxiliary fueling rates and injection timing.