Search Results

A supercritical organic Rankine cycle (ORC) system for recovery of waste heat from heavy-duty diesel engines is proposed. In this system, an organic, medium-boiling-point fluid is selected as the working fluid, which also serves as the coolant for the charge air cooler and the EGR coolers. Because the exhaust temperature can be as high as 650 °C during the DPF regeneration, an exhaust cooler is included in the system to recover some of the high level exhaust energy. In the present ORC system, the expansion work is conducted by a uniflow reciprocating expander, which simplifies the waste-heat-recovery (WHR) system significantly. This reciprocating Rankine engine is more appropriate for on-road-vehicle applications where the condition for waste heat is variable. The energy level of waste heat from a heavy-duty diesel engine is evaluated by the analyses of the first and second law of thermodynamics.

The current paper describes a methodology for combustion bowl assessment for diesel engines. The methodology is based on the application of Computational Fluid Dynamics (CFD) following a Design of Experiments (DoE) procedure. In this work the 3D CFD simulation was performed by the commercial CFD code AVL-FIRE for different combustion bowls from intake valve closing (IVC) to exhaust valve opening (EVO). The initial conditions (at IVC) and boundary conditions were obtained from 1D simulation. Since the work was concentrated on the spray injection, mixing, combustion as well as bowl aerodynamics only a sector mesh was employed for the calculations. A DoE procedure was also used for this simulation work in order to minimize the number of simulation runs and at the same time maintaining the accuracy required assessing the influences of different bowl geometry, spray and intake air motion parameters.

A new fuel injection strategy is proposed for DME engines. Under this strategy, a pre-injection up to 40% demand is conducted after intake valves closing. Due to high volatility of DME, a lean homogeneous mixture can be formed during the compression stroke. Near TDC, a pilot injection is conducted. Combined fuel mass for the pre-injection and pilot injection is under the lean combustion limit of DME. Thus, the mixture is enriched and combustion can take place only in the neighborhood of sprays of the pilot injection. The main injection is conducted after TDC. Because only about half of the demand needs to be injected and DME evaporates almost immediately, combustion duration for the main injection plus the unburnt fuel in the cylinder should not be long because a large portion of the fuel has been premixed with air. With a high EGR rate and proper timing for the main injection, low temperature combustion could be realized.

The fuel saving benefit is analyzed for a class-8 truck diesel engine equipped with a WHR system, which recovers the waste heat from the EGR. With this EGR-WHR system, the composite fuel savings over the ESC 13-mode test is up to 5%. The fuel economy benefit can be further improved if the charge air cooling is also integrated in the Rankine cycle loop. The influence of working fluid properties on the WHR efficiency is studied by operating the Rankine cycle with two different working fluids, R245fa and ethanol. The two working fluids are compared in the temperature-entropy and enthalpy-entropy diagrams for both subcritical and supercritical cycles. For R245fa, the subcritical cycle shows advantages over the supercritical cycle. For ethanol, the supercritical cycle has better performance than the subcritical cycle. The comparison indicates that ethanol can be an alternative for R245fa.

The physical process of particulate fouling in EGR coolers is analyzed in this paper. Various particulate-deposition mechanisms are discussed and an order of magnitude comparison suggests that thermophoresis is the dominant mechanism for the EGR cooler fouling. The EGR temperature at the cooler inlet, the soot particle concentration in EGR, and the EGR mass flow rate are found to be the parameters governing the EGR cooler fouling. The structure for the soot deposit buildup on the cooler wall is also discussed. It is found that the surface layer of the deposit governs the fouling factor. A comprehensive model for soot particle depositions is developed employing heat, mass, and momentum transfer theories for the particle-gas system. The fouling model developed in this study can predict the process of deterioration in the effectiveness. The predictions of EGR cooler fouling are compared with experimental data and good agreement is observed.

On the basis of the newly-developed fractal combustion model, the engine-thermodynamic-cycle simulations were conducted with the 1D engine-cycle-simulation program AVL-BOOST for a passenger-car SI engine with a fully-variable valve train. Results of the simulations showed a good agreement with measurements for both full and part load at various engine speeds. On the basis of the thermodynamic model for the engine, the valve event optimization was carried out for both full and part load with a partial factorial DoE plan consisting of various valve event durations and timings. For each of the selected cases, an independent optimization for the ignition timing was performed to determine the minimum BSFC under a constraint on specified knock criteria. Satisfactory results for the valve event optimization were achieved.

Waste heat from a heavy-duty truck diesel engine is analyzed employing the first and second law of thermodynamics. A hybrid energy system is proposed, with the diesel cycle being hybridized with an organic Rankine cycle for waste heat recovery (ORC-WHR). The charge air cooler and EGR cooler(s) are integrated in the ORC loop as pre-heaters and the ORC working fluid serves as the coolant for these coolers. A supercritical reciprocating Rankine engine is proposed, which avoids using the high-cost evaporator and is easier for the system packaging. It is demonstrated in a case study that up to 20 % of waste heat from the heavy-duty diesel engine may be recovered by the supercritical ORC-WHR system, making the efficiency for the hybrid energy system be ≥ 50%. Discussion on working fluids for the WHR-ORC system is covered in Part II of this paper.

In Part I of this paper, the organic Rankine cycle for waste heat recovery (ORC-WHR) from the heavy-duty diesel truck engines was discussed. This work is Part II of the paper. The efficiency of the ORC-WHR system varies considerably with thermodynamic properties of the working fluid. In this work, characteristics of candidate working fluids are discussed on the basis of the thermodynamic theory. The discussion covers inorganic and organic fluids for both pure fluids and binary-mixture fluids. On the basis of the characteristics of the working fluids, the thermal efficiency for the ORC-WHR system is analyzed. Discussions and conclusions of this paper are helpful in selecting proper working fluids for the ORC-WHR system and determining a proper temperature range for system operations.