Search Results

With the increasing number of urban cars, parking has become the primary problem that people face in daily life. Therefore, many scholars have studied the automatic parking system. In the existing research, most of the path planning methods use the combined path of arc and straight line. In this method, the path curvature is not continuous, which indirectly leads to the low accuracy of path tracking. The parking path designed using the fifth-order polynomial is continuous, but its curvature is too large to meet the steering constraints in some cases. In this paper, a continuous-curvature parking path is proposed. The parking path tracker based on Model Predictive Control (MPC) algorithm is designed under the constraints of the control accuracy and vehicle steering. Firstly, in order to make the curvature of the parking path continuous, this paper superimposes the fifth-order polynomial with the sigmoid function, and the curve obtained has the continuous and relatively small curvature.

The brake-by-wire system (BBW) is better match the new energy vehicle in the future direction of development. The electro-mechanical brake (EMB) is lack of the brake failure backup and need a high 42 V voltage for the power supply. This paper presents a new brake-by-wire hybrid brake system (HBS) with the electro-hydraulic brake (EHB) equipped on the front wheels and the EMB equipped on the rear wheels. The combination of these two brake-by-wire systems has advantages of both the EHB and EMB system. The EMB on the rear wheels totally removing the rear pipes and can be simply mounted. In addition, since the need of brake torque on the rear axle is relatively small, the power supply of EMB can be reduced to 12 V. Meanwhile, the EHB on the front wheels has the failure backup function through the hydraulic line. The HBS can quickly and accurately regulate four wheels brake force of vehicles which can well meet the requirement of antilock brake system (ABS).

With the development of intelligent and electric vehicles, higher requirements are put forward for the active braking and regenerative braking ability of the braking system. The traditional braking system equipped with vacuum booster has difficulty meeting the demand, therefore it has gradually been replaced by the integrated braking system. In this paper, a novel Integrated Braking System (IBS) is presented, which mainly contains a pedal feel simulator, a permanent magnet synchronous motor (PMSM), a series of transmission mechanisms, and the hydraulic control unit. As an integrative system of mechanics-electronics-hydraulics, the IBS has complex nonlinear characteristics, which challenge the accurate pressure control. Furthermore, it is a completely decoupled braking system, the pedal force doesn’t participate in pressure-building, so it is necessary to precisely identify driver’s braking intention.

The slip ratio of vehicle driving wheels is easily beyond a reasonable range in the complex and changeable driving conditions. In order to achieve the adaptive acceleration slip regulation of four-wheel driving (4WD) vehicle, a fuzzy control strategy of Automatic Drive Train Management (ADM) system based on road situation identification was proposed in this paper. Firstly, the influence on the control strategy of ADM system was analyzed from two aspects, which included the different road adhesion coefficients and the vehicle’s ramp driving state. In the meantime several quantitative expressions of relevant control parameters were derived. Secondly, the fuzzy logic control algorithm was adopted to design a road situation identification subsystem and a ramp driving state identification subsystem respectively. The former was based on the μ-S curve model, and the latter was based on the vehicle driving equilibrium equation.

Semi-active suspension system (SASS) could enhance the ride comfort of the vehicle across different operating conditions through adjusting damping characteristics. However, current SASS are often calibrated based on engineering experience when selecting parameters for its controller, which complicates the achievement of optimal performance and leads to a decline in ride comfort for the vehicle being controlled. Linear quadratic constrained optimal control is a crucial tool for enhancing the performance of semi-active suspensions. It considers various performance objectives, such as ride comfort, handling stability, and driving safety. This study presents a control strategy for determining optimal damping force in SASS to enhance driving comfort. First, we analyze the working principle of the SASS and construct a seven-degree-of-freedom model.

Driver individualities is crucial for the development of the Advanced Driver Assistant System (ADAS). Due to the mechanism that specific driving operation action of individual driver under typical conditions is convergent and differentiated, a novel driver individualities recognition method is constructed in this paper using random forest model. A driver behavior data acquisition system was built using dSPACE real-time simulation platform. Based on that, the driving data of the tested drivers were collected in real time. Then, we extracted main driving data by principal component analysis method. The fuzzy clustering analysis was carried out on the main driving data, and the fuzzy matrix was constructed according to the intrinsic attribute of the driving data. The drivers’ driving data were divided into multiple clusters.

As bottom layer actuator for the AEB system, the active brake system and the brake force control of tractor-semitrailer have been the hot topics recently. In this paper, a set of active pneumatic brake system was designed based on the traditional brake system of tractor-semitrailer, which can realize the active brake of the vehicle under necessary conditions. Then, a precise mathematical model of the active pneumatic brake system was built by referring the flow characteristics of the solenoid valve, and some tests were implemented to verify the accuracy and validity of the active brake system model. Based on the model, an active pneumatic brake pressure control strategy combining the feedforward and feedback controlling modes was designed. By generating the PWM control signal, it can precisely control the desired wheel cylinder brake pressure of the active brake system. Finally, the brake pressure control strategy was validated both by simulation tests and bench tests.

The intelligent and electric vehicles are the future of vehicle technique. The development of intelligent and electric vehicles also promotes new requirements to many traditional chassis subsystems, including traditional braking system equipped with vacuum boosters. The Electro-Mechanical Booster is an applicable substitute of traditional vacuum booster for future intelligent and electric vehicles. It is independent of engine vacuum source, and can be combined with electric regenerative braking. A complete system model is necessary for system analysis and algorithm developing. For this purpose, the modeling of electro-hydraulic braking system is necessary. In this paper, a detailed electro-hydraulic braking system model is studied. The system consists of an electro-mechanical booster and hydraulic braking system. The electro-mechanical booster which mainly contains a permanent magnet synchronous motor (PMSM) and a set of transmission mechanism is the critical component.

The Electro-Mechanical Brake Booster (Ebooster) is a critical component of the novel brake system for electric intelligent vehicles. It is independent of engine vacuum source, provides powerful active brake performance and can be combined with electric regenerative braking. In this paper, a brake control algorithm for hydraulic brake system equipped with an Ebooster is proposed. First, the configuration of the Ebooster is introduced and the system model including the permanent magnet synchronous motor (PMSM) and hydraulic brake system is established by Matlab/Simulink. Second, a Four-closed-loop algorithm is introduced for accurate active brake pressure control. Finally, according to the requirement of different brake force, series of simulations are carried out under active braking condition. The results show that the control algorithm introduced in this paper can ensure the brake hydraulic pressure tracking a target value precisely and show a good control performance.

The Electro-Mechanical Brake Booster system (EMBB) is a kind of novel braking booster system, which integrates active braking, regenerative braking, and other functions. It usually composes of a servo motor and the transmission mechanism. EMBB can greatly meet the development needs of vehicle intelligentization and electrification. During active braking, EMBB is required to respond quickly to the braking request and track the target pressure accurately. However, due to the highly nonlinearity of the hydraulic system and EMBB, traditional control algorithms especially for PID algorithm do not work well for pressure control. And a large amount of calibration work is required when applying PID algorithms to pressure control in engineering.

This paper describes a novel recognition and classification method of vehicle targets in urban road based on a vehicle-mounted Velodyne HDL64E light detection and ranging (LIDAR) system. The autonomous vehicle will choose different driving strategy according to the surrounding traffic environments to guarantee that the driving is safe, stable and efficient. It is helpful for controller to provide the efficient stagey to know the exact type of vehicle around. So this method concentrates on reorganization and classification the type of vehicle targets so that the controller can provide a safe and efficient driving strategy for autonomous ground vehicles. The approach is targeted at high-speed ground vehicle, so real-time performance of the method plays a critical role. In order to improve the real-time performance, some methods of data preprocessing should be taken to simplify the large-size long-range 3D point clouds.

Electrification and intelligence are the important development directions of vehicle techniques. The Electro-Mechanical Brake Booster (Ebooster) as a brake booster which is powered by a motor, can be used to replace the traditional vacuum booster. Ebooster not only improves the intelligence level of vehicle braking and significantly improves the braking performance, but also adapts to the application in new energy vehicles and facilitates coordinated regenerative braking. However, Ebooster cannot complete pedal decoupling independently. It needs to cooperate with other components to realize pedal decoupling. In this paper, a pedal decoupling control algorithm for regenerative brake, which is based on the coordination control of Ebooster and ESP, is proposed. First, regenerative braking strategy is designed to distribute the hydraulic brake force and regenerative braking force.

As a new brake-by-wire solution, the electro-booster (Ebooster) brake system can work with the electronic stability program (ESP) equipped in the real vehicle to realize various excellent functions such as basic force boosting (BFB), active braking and energy recovery, which is promoting the development of smart vehicles. Among them, the BFB is the function of Ebooster's servo force to assist the driver's brake pedal force establishing high-intensity braking pressure. After the BFB function failure of the Ebooster, it was not possible to provide sufficient brake pressure for the driver's normal braking, and eventually led to traffic accidents. In this paper, a compensation redundancy control strategy based on ESP is proposed for the BFB failure of the self-designed Ebooster.