Search Results

Some of the methods used for experimental detection and examination of wake vortices are presented. The aim of the article is to provide the reader a brief overview of the available methods. The material is divided into two major sections, one dealing with methods used primarily in the laboratory, and the second part devoted to those used in field operations. Over one hundred articles are cited and briefly discussed.

As part of a general aviation airfoil development program being carried out under the direction of the NASA Langley Research Center, a 30% chord Fowler flap has been developed for the GA(W)-1 airfoil.. Wind tunnel tests at Wichita State University have demonstrated a c1max value of 3.80 for 40 deg flap deflection at a Reynolds number of 2.2 × 106. Effects of flap slot geometry have been systematically tested and optimum flap settings for any flight c1 have been obtained. Modification of the reflexed lower surface contour resulted in a reduced c1max with flap nested. Vortex generators provided an increase in c1max of 0.2 for flap nested and 40 deg flap along with a drag penalty at low c1 values. Flow visualization studies show that the stalling patterns for the new airfoil are characterized by an absence of leading edge separation for both the flap-nested and the 40 deg flap cases.

Metal cutting is a substantial constituent of airframe manufacturing. During the past several decades, it has evolved significantly. However, most of the changes and improvement were initiated by the machine tool industry and cutting tool industry, thus these new technologies is generally applicable to all industries. Among them, few are developed especially for the airframe manufacture. Therefore, the potential of high efficiency could not be fully explored. In order to deal with severe competition, the aerospace industry needs improvement with a focus on achieving low cost through high efficiency. The direction of research and development in parts machining must comply with lean manufacturing principles and must enhance competitiveness. This article is being forwarded to discuss the trend of new developments in the metal cutting of airframe parts. Primary driving forces of this movement, such as managers, scientists, and engineers, have provided significant influence to this trend.

An experimental investigation was conducted to identify the aerodynamic effects of oversized low-pressure (Tundra) tires and tall landing gear on a Piper Super Cub airplane. Water tunnel and wind tunnel tests were performed using, respectively, a 1/20 scale model and full-scale landing gear and tire components. Force and moment data suggest that larger tires and taller gear most affect the drag and side force. Small trim changes are apparent, but the basic static stability behavior appears unchanged.

Aerospace manufactures purchase millions of drill bits each year for the manufacture of large aircraft structures. This paper describes an ongoing research project for the development of an automated system to detect poor quality drill bits before they are put to use.

This paper presents experimental methods for investigating large droplet impingement dynamics and for obtaining small and large water droplet impingement data. Droplet impingement visualization experiments conducted in the Goodrich Icing Wind Tunnel with a 21-in chord NACA 0012 airfoil demonstrated considerable droplet splashing during impingement. The tests were performed for speeds in the range 50 to 175 mph and with cloud median volumetric diameters in the range of 11 to 270 microns. Extensive large droplet impingement tests were conducted at the NASA Glenn Icing Research Tunnel (IRT). Impingement data were obtained for a range of airfoil sections including three 36-inch chord airfoils (MS(1)-0317, GLC-305, and NACA 652-415), a 57-inch chord Twin Otter horizontal tail section and 22.5-minute and 45-minute LEWICE glaze ice shapes for the Twin Otter tail section. Small droplet impingement tests were also conducted for selected test models.

Force measurements, surface flow patterns and wake total pressure surveys have been obtained for a wing, wing--body, wing-nacelle and wing-body--nacelle configuration at typical pre-and post-stall angle of attack (10° and 16°), for a general aviation twin-engine airplane. The data includes separated regions and combined flow field models. The results indicate the presence of highly three-dimensional separated regions above and beyond the surface at post-stall condition. Based upon the present experimental data, combined flow field models have been proposed for each of the configurations, at the pre-stall (10°) and post -stall (16°) angle of attack condition. In all cases, the flow is shown to be forming turbulent three-dimensional separation bubbles. These flow models should provide some guidelines for future analytical modeling of separated flow associted with interfering bodies.

A supplier satisfaction survey was developed and administered to 129 Aircraft suppliers who are AS9100 registered. The primary objective of the survey was to assess organizational benefits, attributed to the AS9100 standard, and registration process difficulties. Survey results from 49 responses indicated that the primary reason for seeking AS9100 registration was customer requirement, followed by improving production and service. Further analysis indicated that the top three difficulties were evaluating effectiveness of employee training, obtaining and analyzing data on customer feedback and satisfaction, and monitoring and measuring processes. The top three reported benefits, improved quality awareness among employees, an increase in employee training, and improved internal communication, respectively, were all non-financial in nature.

A series of carefully selected tests were used to isolate the coupled influence of various combinations of the number of facesheet plies, impact energies, and impactor diameters on the damage formation and residual strength degradation of sandwich composites due to normal impact. The diameter of the planar damage area associated with Through Transmission Ultrasonic C-scan and the compression after impact measurements were used to describe the extent of the internal damage and residual strength degradation of test panels, respectively. Standard analysis of variance techniques were used to assess the significance of the regression models, individual terms, and the model lack-of-fit. In addition, the inherent variability associated with given types of experimental measurements was evaluated.

While most industries have already adopted the use of IP networks to exploit the many advantages of network connectivity, the aircraft industry still has not significantly deployed networked devices in the aircraft. Security and reliability are two main concerns that have slowed the transition to this technology. The ability for Air Traffic Control to send digital communications to aircraft could significantly improve the aircraft safety by improving the speed and efficiency of communications. In addition, if devices could offload flight data to servers on the ground for analysis, the accuracy and efficiency of maintenance and other decisions impacting the aircraft could significantly improve. The purpose of this research is to propose an IP-based LAN architecture for the aircraft which provides a scalable solution without jeopardizing flight safety.

In-service data from two Bombardier business jets, a Global 5000 and a Global Express XRS, have been compared. Flight data has been analyzed from both airframes with comparable number of ground-air-ground cycles. Individual flight phase have been examined and compared between the two airframes. Primary emphasis has been placed on airframe usage. The influence of primary mission on ground-air-ground cycles has been highlighted in the form of ground and flight loads, as well as dynamics of the flights. It is demonstrated that safe-life maintenance approach may have to be adjusted to account for the airframe usage.

Laminated metal-metal composites can have attractive fracture toughness properties; they also offer potentially good fatigue performance. These attributes are reviewed and prospects for improvement discussed. Weak interlaminar bonds are seen to be important, while quite thin layers seem to be most promising for laminates of higher strength materials. The experimental program utilized 0.033 in (0.84 mm) thick laminae of 7075-T6 aluminum alloy, adhesively bonded. Eight-layer composites were compared with solid sheets of nearly the same total metal thickness. Both fracture toughness and fatigue properties were determined. Kc values of more than double the KIc for this alloy were observed in the laminates, while fatigue performance as indicated by comparative S-N curves was found to be slightly improved.

The coupled influence of material configuration (number of facesheet plies, core density, core thickness) and impact parameters (impact velocity and energy, impactor diameter) on the impact damage resistance characteristics of sandwich composites comprised of carbon-epoxy woven fabric facesheets and Nomex honeycomb cores was investigated using empirically based quadratic response surfaces. The diameter of the planar damage area associated with TTU C-scan measurements and the peak residual facesheet indentation depth were used to describe the extent of internal and detectable surface damage, respectively. Estimates of the size of the planar damage region correlated reasonably well with experimentally determined values. For a fixed set of impact parameters, estimates of the planar damage size and residual facesheet indentation suggest that impact damage development is highly material and lay-up configuration dependent.

During this study, a number of 8.5-inch by 11.5-inch flat honeycomb sandwich panels were inflicted with low energy impact damage, inspected non-destructively, and tested for residual in-plane compressive strength. Each panel had either a 3/8-inch or 3/4-inch low density Nomex honeycomb core, and either 2-ply, 4-ply or 6-ply face sheets. The face sheets were either carbon or Eglass (prepreg) fabric. The panels were either clamped or simply supported in a test fixture during impact from a gravity assisted drop mechanism, and impacted with either a 1-inch or 3-inch diameter spherical indenter. After impact the damage to each panel was characterized by (1) ultrasonic through-transmission to obtain a c-scan representing planar damage area, (2) indentation volume and depth, and finally (3) visual inspection to rate the damage according to a predetermined rating scale. The panels were then tested for in-plane compressive strength.

Data obtained from digital flight data recorders are used to assess the actual operational environment of propellers on a fleet of Beech 1900D aircraft in commuter role. Information is given on various aerodynamic parameters as well as those pertaining to engine and propeller usage. The takeoff rotation has been identified as the most demanding phase of flight in terms of unsteady loads exerted on the propeller blades. Special attention is paid to ground operations.

A unique cascade test facility has been developed for use in the Wichita State University (WSU) water table. Although small in scale, the WSU water table has the advantage of low cost and the ease with which test conditions can be varied. Water table facilities have been used in the past for cascade experiments, especially as analogies for compressible flow visualization of turbine cascades. However, the lack of a quantitative measurement technique at low speeds has precluded the use of the water table as an analogy for testing subsonic compressors and turbines. In the present experiment, the hydrogen bubble flow visualization technique is used to generate bubble time lines, and a CCD (Charge Coupled Device) video camera system captures and digitizes these time line images. A VisualBASIC® computer program is then used to determine the wake velocity profile based on the difference in bubble line positions at successive intervals of time.

The work presented here illustrates the wear behavior of CVD diamond coated carbide tools during the machining of carbon fiber-reinforced composites. Cutting experiments were conducted on a CNC milling machine for edge trimming of a 9-mm thick multi-layered carbon fiber-reinforced epoxy laminate in a climb cutting configuration. The effects of feed speed and diamond film thickness on the wear behavior of the coated tools were determined. In addition, characteristics of the worn cutting edge were studied using optical and scanning electron microscopes. It was shown that diamond coated tools generally performed better than the uncoated tools under all conditions. Uniform wear by abrasion of the diamond film, without exposing the substrate, was obtained when cutting at low feed speeds with thicker coatings. At higher feed speeds the wear of the coated tools was characterized by abrasion through the diamond film and exposure and wear of the substrate.

In the present work we studied the edge trimming process of CFRP with a diamond interlocking “burr” tool. Measurements of tool wear, surface roughness, spindle power and delamination depth were performed for different combinations of spindle speed and feed rate and were subsequently used to characterize machining quality. It was found that direct wear measurement for this type of cutting tool is not conclusive and thus not suitable for assessing tool life and machining quality. Instead, indirect indicators of tool wear were found more suitable for this purpose. Using these indirect methods an equation for tool life was defined and parameters for optimum machining quality were determined.

Most composite assemblies and structures generally fail due to weak interlaminar properties and poor performance of their bonded joints that are assembled together with an adhesive layer. Adhesive failure and cohesive failure are among the most commonly observed failure modes in composite bonded joint assemblies. These failure modes occur due to the lack of reinforcement within the adhesive layer in transverse direction. In addition, the laminated composites fail due to the same reason that is the lack of reinforcement through the thickness direction between the laminae. The overall performance of any composite structures and assemblies largely depends on the interlaminar properties and the performance of its bonded joints. Various techniques and processes were developed in recent years to improve mechanical performance of the composite structures and assemblies, one of which includes the use of nanoscale reinforcements in between the laminae and within the adhesive layer.

An experimental study was conducted to investigate ice-adhesion on clean and coated aluminum surfaces. A test apparatus using the parallel plate linear shear technique was designed along with a data acquisition system for conducting the tests and recording the experimental data. A low pulling rate was applied to specially prepared test specimens for measuring the strength of ice adhesion for a range of test conditions. The effects of surface roughness, surface contamination, and water impurity on ice adhesion were investigated. In addition, tests were conducted to evaluate the effectiveness of a low ice-adhesion coating applied to aluminum test specimens. The results obtained showed that the bond between ice and metal was considerably lower for tap water than for distilled water. For the clean and coated aluminum surfaces the strength of ice adhesion varied with specimen roughness. However, no clear trend was established between ice adhesion strength and surface roughness.