Search Results

As part of a general aviation airfoil development program being carried out under the direction of the NASA Langley Research Center, a 30% chord Fowler flap has been developed for the GA(W)-1 airfoil.. Wind tunnel tests at Wichita State University have demonstrated a c1max value of 3.80 for 40 deg flap deflection at a Reynolds number of 2.2 × 106. Effects of flap slot geometry have been systematically tested and optimum flap settings for any flight c1 have been obtained. Modification of the reflexed lower surface contour resulted in a reduced c1max with flap nested. Vortex generators provided an increase in c1max of 0.2 for flap nested and 40 deg flap along with a drag penalty at low c1 values. Flow visualization studies show that the stalling patterns for the new airfoil are characterized by an absence of leading edge separation for both the flap-nested and the 40 deg flap cases.

This paper presents experimental methods for investigating large droplet impingement dynamics and for obtaining small and large water droplet impingement data. Droplet impingement visualization experiments conducted in the Goodrich Icing Wind Tunnel with a 21-in chord NACA 0012 airfoil demonstrated considerable droplet splashing during impingement. The tests were performed for speeds in the range 50 to 175 mph and with cloud median volumetric diameters in the range of 11 to 270 microns. Extensive large droplet impingement tests were conducted at the NASA Glenn Icing Research Tunnel (IRT). Impingement data were obtained for a range of airfoil sections including three 36-inch chord airfoils (MS(1)-0317, GLC-305, and NACA 652-415), a 57-inch chord Twin Otter horizontal tail section and 22.5-minute and 45-minute LEWICE glaze ice shapes for the Twin Otter tail section. Small droplet impingement tests were also conducted for selected test models.

While most industries have already adopted the use of IP networks to exploit the many advantages of network connectivity, the aircraft industry still has not significantly deployed networked devices in the aircraft. Security and reliability are two main concerns that have slowed the transition to this technology. The ability for Air Traffic Control to send digital communications to aircraft could significantly improve the aircraft safety by improving the speed and efficiency of communications. In addition, if devices could offload flight data to servers on the ground for analysis, the accuracy and efficiency of maintenance and other decisions impacting the aircraft could significantly improve. The purpose of this research is to propose an IP-based LAN architecture for the aircraft which provides a scalable solution without jeopardizing flight safety.

The coupled influence of material configuration (number of facesheet plies, core density, core thickness) and impact parameters (impact velocity and energy, impactor diameter) on the impact damage resistance characteristics of sandwich composites comprised of carbon-epoxy woven fabric facesheets and Nomex honeycomb cores was investigated using empirically based quadratic response surfaces. The diameter of the planar damage area associated with TTU C-scan measurements and the peak residual facesheet indentation depth were used to describe the extent of internal and detectable surface damage, respectively. Estimates of the size of the planar damage region correlated reasonably well with experimentally determined values. For a fixed set of impact parameters, estimates of the planar damage size and residual facesheet indentation suggest that impact damage development is highly material and lay-up configuration dependent.

During this study, a number of 8.5-inch by 11.5-inch flat honeycomb sandwich panels were inflicted with low energy impact damage, inspected non-destructively, and tested for residual in-plane compressive strength. Each panel had either a 3/8-inch or 3/4-inch low density Nomex honeycomb core, and either 2-ply, 4-ply or 6-ply face sheets. The face sheets were either carbon or Eglass (prepreg) fabric. The panels were either clamped or simply supported in a test fixture during impact from a gravity assisted drop mechanism, and impacted with either a 1-inch or 3-inch diameter spherical indenter. After impact the damage to each panel was characterized by (1) ultrasonic through-transmission to obtain a c-scan representing planar damage area, (2) indentation volume and depth, and finally (3) visual inspection to rate the damage according to a predetermined rating scale. The panels were then tested for in-plane compressive strength.

A unique cascade test facility has been developed for use in the Wichita State University (WSU) water table. Although small in scale, the WSU water table has the advantage of low cost and the ease with which test conditions can be varied. Water table facilities have been used in the past for cascade experiments, especially as analogies for compressible flow visualization of turbine cascades. However, the lack of a quantitative measurement technique at low speeds has precluded the use of the water table as an analogy for testing subsonic compressors and turbines. In the present experiment, the hydrogen bubble flow visualization technique is used to generate bubble time lines, and a CCD (Charge Coupled Device) video camera system captures and digitizes these time line images. A VisualBASIC® computer program is then used to determine the wake velocity profile based on the difference in bubble line positions at successive intervals of time.

An experimental study was conducted to investigate ice-adhesion on clean and coated aluminum surfaces. A test apparatus using the parallel plate linear shear technique was designed along with a data acquisition system for conducting the tests and recording the experimental data. A low pulling rate was applied to specially prepared test specimens for measuring the strength of ice adhesion for a range of test conditions. The effects of surface roughness, surface contamination, and water impurity on ice adhesion were investigated. In addition, tests were conducted to evaluate the effectiveness of a low ice-adhesion coating applied to aluminum test specimens. The results obtained showed that the bond between ice and metal was considerably lower for tap water than for distilled water. For the clean and coated aluminum surfaces the strength of ice adhesion varied with specimen roughness. However, no clear trend was established between ice adhesion strength and surface roughness.

Dynamic aircraft seat regulations are identified in the Code of Federal Regulations (CFR), 14 CFR Parts § 23.562 [1] and § 25.562 [2] for crashworthy evaluation of a seat in dynamic environment. The regulations specify full-scale dynamic testing on production seats. The dynamic tests are designed to demonstrate the structural integrity of the seat to withstand an emergency landing event and occupant safety. SAE standard AS 8049 [3] supports detailed information on dynamic seat testing procedure and acceptance criteria. Full-scale dynamic testing in support of certification is expensive and repeated testing due to failure drastically increases the expense. Involvement of impact environment, flexibility in interior configuration and complicated nature of seat engineering design makes this problem quite complex, so that classical hand calculations are practically impossible.

Flight test experiments were conducted to measure the extent and nature of natural laminar flow on a smoothed test region of a swept-wing business jet wing. Surface hot film aneraometry and sublimating chemicals were used for transition detection. Surface pressure distributions were measured using pressure belts. Engine noise was monitored by a microphone attached to the wing surface to study possible acoustic effects on stability of the laminar boundary layer, Side-slip conditions were flown to simulate changes in effective wing sweep. Flight instrumentation and ground data analysis techniques and a method for measuring intermittency of turbulence are described, Correlation was obtained between the hot film gage signals and chemicals for transition detection. Cross-flow vortices were observed for some flight conditions. Results of spectral and statistical analysis of the hot film signals for various flight test conditions are presented.

An algorithm is developed and validated for automatic avoidance of restricted airspaces. This method is devised specifically for implementation with an advanced flight control system designed for general aviation application. The algorithm presented here implements two inputs to the aircraft; the bank angle, and the airspeed, while the control system always ensures coordinated maneuvers. Unlike collision avoidance systems, the current method is not designed to serve in an advisory role, but to assume complete control of the aircraft if necessary. It is demonstrated that in order to implement this technique, the aircraft must be assigned an immediate domain whose size would have to depend on the aircraft performance and flight conditions. The strategy is designed such that as the domain surrounding the aircraft approaches that of the restricted airspace, aircraft control would switch gradually away from the pilot and to the controller, which would initiate an evasive maneuver.

An experimental study was performed to investigate large droplet dynamics in the vicinity of an airfoil. The investigation was conducted using the NASA Glenn Droplet Imaging Flow Tunnel (DrIFT). Mono-dispersed large droplets were released at the tunnel inlet and accelerated toward an airfoil that was mounted in the test section. The dynamic behavior of a droplet's encounter with the airfoil, which may involve droplet distortion, break-up, impingement and splashing, was recorded using a high-speed imaging system. The effects of the droplet size, tunnel velocity and airfoil configuration on the droplet dynamics were investigated in a parametric study. The droplet sizes used in the experimental study were 96 and 375 μm whereas tunnel velocities were varied from 80 to 130 mph. Three different airfoil geometries were used in the experimental study; a ‘clean’ and ‘iced’ airfoil, and a ‘clean’ three-element high-lift airfoil. The incidence angle of these airfoils was set to zero degrees.

The necessity of avoiding the destructive and non-repeatable FSST (Full Scale Sled Test) makes it desirable to devise a cheaper and more repeatable method which can supplant this test procedure. This need developed the HCTD (HIC Component Testing Device) which is capable of providing conservative HIC results with higher repeatability. The computational model of the HCTD is validated against one of the tests conducted at CAMI with polyethylene foam. This validated model is used to conduct a series of tests with input parameters similar to the sled test to develop the correlation between the sled test and HCTD. This study hence concludes that a validated computational model of HCTD can be successfully utilized to address the HIC compliance issues for a foam padded surface.

This study presents the prediction of the dimensional variation of holes due to sheet metal bending using the hydroforming technique. Sheet metal with pre-drilled holes was evaluated for a bending operation using a hydroforming technique. Sheet metal with a variety of thicknesses, bending radii, and bending angles was evaluated. Variation in the dimensional tolerance due to the bending was attained using the minimum radial separation method. A dataset of dimensional variation in the holes was developed and used for development of the artificial neural network, which was able to predict the dimensional variation of the hole if an unknown pattern of inputs was provided.

An envelope protection scheme is proposed for responding to a microburst. This approach is based on limiting the allowable maximum inertial deceleration of the aircraft when flying at low airspeeds. This technique is shown in simulations to be very effective at preventing stall and resulting in minimal loss of altitude. It is speculated that the same scheme can also protect an aircraft in the event of other forms of windshear encounters, such as making a sudden turn to downwind.

While operational airships globally number in the low dozens, interest in buoyant or semi-buoyant platforms continues to arouse imaginations of commercial and military planners and developers alike. The airship-as-advertisement business model is the only model that has proven sustainable on any scale since the crash of the initially successful LZ-128 Hindenburg effectively ended regular passenger and cargo transport by airship, and the 1962 termination of the US Naval airship program terminated regular large-scale surveillance from airships. Efforts in the US and Japan during the 2000's to have a self-sustaining sight-seeing business model using the modern semi-rigid Zeppelin NT both failed. In theory, the buoyant nature of airships provides compelling endurance and cost-per-ton-mile capability which fills a niche arguably not currently occupied by other modes of transportation.

Research has been conducted on the nature of airfoil behavior at pre- and post-separated angles of attack. Detailed wind tunnel studies have been made of boundary layer and wake fields for the GA(W)-1 airfoil, and the airfoil with a 0.3 chord Fowler flap. Experimental data are compared with theoretical predictions from a multi-element viscous flow computer program. Theoretical predictions are reasonably accurate for unseparated flows, but have serious errors when separation is present. Some recent techniques for modeling post-separated flow behavior are discussed in light of the present experiments.

Wind tunnel test have been conducted to determine effects of certain design variables on spoiler performance and spoiler flow field characteristics. Measurements include forces, oil flow surveys on a vertical splitter plate, and wake velocity and turbulence measurements using a dual split-film anemometer system. Results include the effects of spoiler design variables, such as: hingeline gap, lower surface venting and deflector, spoiler trailing edge notching and spoiler porosity. Hingeline gap, porosity, lower surface venting and lower surface deflector can be designed to reduce control dead-band tendency. Wake turbulence studies show that certain modifications can be utilized to diminish peak frequencies in the wake.

The results of an analytical study of aerodynamic interference effects for a light twin aircraft are presented. The data presented concentrates on the influence of a wing on a body (the fuselage). Wind tunnel comparisons of three fillets are included, with corresponding computational analysis. Results indicate that potential flow analysis is useful to guide the design of intersection fairings, but experimental tuning is still required. While the study specifically addresses a light twin aircraft, the methods are applicable to a wide variety of aircraft.

This paper presents a method by which artificial neural networks can be trained and used to identify a possible spin entry, differentiate between an incipient spin and a stabilized spin, and predict required recovery controls. These were then implemented into a simulation and tested using data from actual flight tests conducted by NASA Langley Research Center, to verify that artificial neural networks can successfully be used for this application. The spin avoidance and recovery system functioned properly. In addition, a weighting system was developed to predict possible spin characteristics of aircraft, depending on the relative magnitude of the three principal moments of inertia.

Wind tunnel tests have been carried out to develop a spoiler lateral control system for use with the GA(W)-1 airfoil with a 30% Fowler flap. Tests show that unfavorable aerodynamic interactions can occur between spoiler and flap for large flap deflections. Providing venting of lower surface air through the spoiler opening substantially improves performance. Results of tests with a number of spoiler and cavity shapes are presented and discussed. Applications of two-dimensional wind tunnel results to the design of satisfactory manual lateral control systems are discussed.