Search Results

Connecting rod design factors, such as geometric shape, capscrew torque and materials can significantly affect bore distortion and assembly stress. In this paper, experiments using different materials were conducted on several connecting rod big-ends with various shapes, bosses and bolts. The results show that the distortion of the big-end bore and the bolt stress are influenced considerably by the big-end shape, the bolt axial tension and the material under inertia force. It was also observed that the bolt bending stress and the load separating the big-end joint surface could be calculated with high accuracy using three-dimensional FEM in the initial connecting rod design.

Reduction in the cycle-to-cycle variation (CCV) of combustion in internal combustion engines is required to reduce fuel consumption, exhaust emissions, and improve drivability. CCV increases at low load operations and lean/dilute burn conditions. Specifically, the factors that cause CCV of combustion are the cyclic variations of in-cylinder flow, in-cylinder distributions of fuel concentration, temperature and residual gas, and ignition energy. However, it is difficult to measure and analyze these factors in a production engine. This study used an optically accessible single-cylinder engine in which combustion and optical measurements were performed for 45 consecutive cycles. CCVs of the combustion and in-cylinder phenomena were investigated for the same cycle. Using this optically accessible engine, the volume inside the combustion chamber, including the pent-roof region can be observed through a quartz cylinder.

The behavior of the liquid in the motorcycle fuel tank is an interesting theme from the viewpoint of the fuel meter construction, as effected by variance in the fuel pressure resulting from acceleration or deceleration, etc. It can be assumed that the behavior of the liquid in the fuel tank will be affected by the running pattern, the shape and capacity of the fuel tank, etc. Here is a report on an experiment recently made to observe how the liquid behaves in a partially fully enclosed tank. We simplified the tank shape and the involved conditions (to actually observe the behavior of the inside liquid by the suspension method.) Then we have analized the effectes according to different liquid containers, to different velocities, and to different liquid volumes as well as the time history variance in the internal pressure.

This paper presents an approach for efficiently evaluating motorcycle main frame strength using external loads predicted from measured strain data in our development process. The loads are calculated by simple matrix inversion, and can be used as boundary conditions of static analysis that resembles actual phenomena. The advantage of this method is that it allows relatively precise reproduction of actual boundary conditions without the data usually needed for dynamic simulation such as tire and suspension characteristics which often take large amount of time and man-hour to obtain. Although this approach is simple and common practice, there are a lot of things to be concerned for gaining useful results in a broad range of stages in the motorcycle main frame development process. How we effectively make use of this approach is going to be introduced here.

Recently it is becoming more necessary than ever to carry out performance prediction and factor analysis at the initial design by-computer aided engineering (CAE), in order to ensure the high performance, safety and reliability of motorcycles and also to shorten the lead time of product development. Finite element method (FEM) plays a crucial role in this respect. In particular, since the vibration characteristic is one of the most important evaluation items, the demand for accurate vibration prediction at the initial design has become much more intense. In recent years, vibration simulation methods have achieved remarkable progress, and especially the substructural synthesis method (SSM), combined with FEM, is used as an effective tool for the requirements.

In order to obtain more reduction of two-stroke motorcycle engine noise than usual, it becomes necessary to make improvements within the combustion process itself. This study was carried out for two objectives. One is the investigation of the relationship between combustion and noise, and the other one is the development of noise reduction techniques. As the result, it was discovered that there was a significant correlation between engine noise and (dP/dθ)max, called the maximum rate of cylinder pressure rise. Therefore, the reduction of the (dP/dθ) max was recognized to be effective for engine noise reduction. The optimized alteration of combustion chamber shape is the most effective noise reduction technique, because it is able to reduce (dP/dθ) max without any sacrifice of engine power. In fact, the level of noise reduction can be predicted by one of the parameters obtained from the combustion chamber shape.

Generally, the gearshift mechanism for outboard motors shifts into forward or reverse gear without using the synchromesh arrangement (dog clutch engagement)(See Fig.1). This type of shift mechanism has advantages in simple structure and in saving space and cost, but at the same time, this is often the source of problem due to the abrasion caused by the hitting of gear against the dog clutch before the engagement, as well as large gearshift shock and noise. In addition, the outboard motor horsepower is getting bigger in recent years. As they are equipped with bigger and heavier engines and propellers, the shifting shock and noise tend to become more severe. For this reason, the improvement in this aspect is required. We looked into the way to reduce the shock and noise by means of propellers, because the propeller can be mounted and replaced easily, which allows the effective improvement to be spread to the outboard motors already in the market.

This paper presents a practical simulation model of the rubber V-belt CVT which is widely used as a low cost driveline element for small displacement motorcycles. The characteristic of this CVT is determined by the axial force balance between driver and driven pulleys, and the elastic force of a rubber V-belt. Because these axial and elastic forces are calculated by the kinematic and FEM analysis, a large-scale simulation model which costs long execution time for the calculation is needed to estimate the characteristic of CVT. This calculation uses the one-dimensional simulation model built up with MATLAB and SIMULINK environment, so that it was possible to get the calculation result with relatively low execution time. The elastic deformation of the rubber V-Belt was calculated by a simple spring model which was verified by experiments and FEM.

The continuously variable transmission (CVT) with a rubber belt used in scooters is also regarded as a potential automatic transmission mechanism for conventional motorcycles. By making this system more compact and building it into the engine, a motorcycle CVT engine has been developed that is about the same size as a manual transmission (MT) engine. During driving with a CVT, heat is generated by friction at the sheaves, and therefore it was necessary to secure a certain length of belt to ensure that external air flows efficiently to the sheaves. However, making the CVT more compact restricted the belt length, which decreased cooling performance and increased the number of bends in the belt, making it difficult to maintain durability. To address this issue, a plastic resin drive belt and newly designed sheaves were adopted, and durability of more than that of a scooter was achieved.

The fracture splitting (FS) method for case hardened connecting rods has been developed to improve engine performance while decreasing production costs. The FS method is widely used for automotive connecting rods because it effectively improves their productivity. Normalized forging steels, microalloyed forging steels and powder metals have generally been used as the material in the FS method as they are easily split due to their brittleness. On the other hand, the materials to be used for high performance motorcycles are case hardened low carbon steels because they allow the connecting rods to be lightweight due to their high fatigue strengths. These materials, which have a hardened area of approx. 0.5mm in depth from the surface, have a ductile texture inside. This texture obstructs the crack propagation and makes the split force too high to split without deforming the bearing area.

A connecting rod made of titanium alloy is effective for lower fuel consumption and higher power output comparing to a steel one because the titanium connecting rod enables to reduce the weight of both of reciprocating and rotating parts in an entire engine substantially. But up to now, it has been adopted only to expensive and small-lot production models because a material cost is high, a processing is difficult and a wear on a sliding area should be prevented. In order to adopt the titanium connecting rods into a more types of motorcycles, appropriate materials, processing methods and surface treatment were considered. Hot forging process was applied not only to reduce a machining volume but also to enhance a material strength and stiffness. And the fracture-splitting (FS) method for the big-end of the titanium connecting rod was put into a practical use.

Laser powder bed fusion is one of the metal additive manufacturing technologies, so-called 3D printing. It has attracted great attentions due to high geometrical flexibility and remarkable metallurgical characteristics. An oil catch tank has been widely used in automotive industries for filtering oil vapors or carbon sludge from blow-by gas as a conventional usage. A pneumatic valve system mainly adopted to high-performance engines is also a potential application of it because undesirable oil infiltrates into air springs during engine operation, resulting in an excess spring pressure. This work focused on developing a lightweight oil catch tank which can be applied to a pneumatic valve system by taking advantage of additive manufacturing techniques. Al-Mg-Sc alloy powder with high tensile strength as well as high ductility were used under the consideration of specific strength, printability and availability.

A control system for auto driving of motorcycle using anthropomorphic robot has been developed to efficiently evaluate a motorcycle with high accuracy, the performance of which is becoming higher. For magnetostriction-type load sensor, which is absolutely necessary for this system, the strain gauge type load cell has been used conventionally. However, the detection sensitivity, strength, and responsibility have not been satisfied completely under engine vibration conditions. To solve this problem, a magnetostriction-type load sensor has been newly developed. As a result of the tests with actual machines, it is found that this magnetostriction-type load sensor satisfies the conditions necessary for the motorcycle drive control system and measurement system.

Recently the response of the engine speed at starting has more importance than ever for quick start satisfying rider’s needs, as well as exhaust emissions. We have developed a simulation for studying engine and starter specifications, engine control algorithm and other engine control parameters. This system can be utilized to realize appropriate starting time by considering air-fuel ratio under various conditions. This paper addresses what are taken account of in our method. Examples applying this to a conventional motorcycle engine are shown.

This paper describes the development of a new concept two-wheel steering system for realizing motorcycle motion control. By considering the whole of the main frame as the rear-wheel steering axis, it was possible to move the rear-wheel steering system from the conventional installation position at the rear arm to the head pipe. As a result, the developed two-wheel steering system is both lightweight and compact. This two-wheel steering system was installed in a motorcycle, and starting and stopping tests were carried out with two people riding on the motorcycle. The test results confirmed that the two-wheel steering system is capable of changing the motion characteristics of the motorcycle in actual riding. Furthermore, by calculating the equivalent wheel alignment of this system, this paper also theoretically demonstrates that these changes in motion characteristics are caused by changes in caster and trail.

It is in the plating process that the worst bottleneck occurs in plant automation. We, however, have succeeded in making our plating process free from pollution and compact, allowing us to install this system within a production line and consequently establish a continuous production line resulting in a decrease in plating cost to about 1/2 of the previous cost. We have achieved an excellent chrome plating speed of 60µ/min, by placing an anode relatively close to the part to be plated and by sending the plating solution into the space between the two by means of a pump. This provides a plating speed 100 times faster than with conventional methods, while improving the quality of the plating coat considerably. The system is optimum for functional platings, and can be used for the plating of shock absorber rods, engine valves, engine cylinders, etc.

An original multi-body dynamics simulation program for reciprocating engine system with elastically deformable piston skirt was developed in order to understand and examine the secondary motion of piston. This program uses specialized equations of motion using only the rotational degree of freedom of each components taking the valiation of rotating speed of crank into account. In order to validate the practical use of this program, the calculations were compared with the measurements on the piston motion of a two-stroke engine for motorcycles and a four-stroke engine for automobiles, and good agreements were obtained between them.

Any improvements of the fuel economy with engines are always required for all petroleum fuel vehicles. The goal of such improvements must lead to reduce fuel consumption of the engines. However it may cause some deterioration with riding feeling that is one of the most important characteristics of the motorcycles. Yamaha has developed the strong hybrid motorcycle "HV-X"(hereafter the motorcycle). The motorcycle consists of a 4-stroke 250 cm₃ a cylinder engine and two 300V AC motors with a planetary gear set. The motorcycle reduces fuel consumption without severe influence onto the drive performance by utilizing the electric power.

In recent years, efforts to reduce CO2 emissions (carbon neutrality) have accelerated worldwide. In the aluminum manufacturing industry, CO2 emissions can be reduced by switching the raw materials of choice; from virgin ingots to recycled ingots. However, the possible characteristic change accompanying the usage of impurity-ridden recycled ingots severely limits its applications, which also limits its potential contribution to carbon neutrality. Determining how impurity elements present in recycled ingots can affect the function of manufactured components is a necessary first step towards expanding the usage of recycled ingots. In this study, we aimed to apply recycled ingots to the monolithic cylinder made of hypereutectic Al-Si alloy and investigated how impurity elements in recycled ingots affect properties (especially seizure characteristic). Die-cast cylinders using virgin and recycled ingots were manufactured and their properties were investigated.

Carburized and quenched materials with high fatigue strength are often used for motorcycle engine parts. Nitrided materials exhibit less deformation during heat treatment than carburized and quenched materials, so if the same or higher fatigue strength can be achieved with nitrided materials as with carburized and quenched materials, the geometric precision of parts can be increased and we can reduce engine noise as well as power loss. When the fatigue strengths of a nitrided material with its compound layer surface put into γ’ phase through nitriding potential control (hereafter, G), and a nitrided material put into ε phase (hereafter, E) were measured, the results showed the fatigue strength of the G to be about 11% higher than that of carburized and quenched materials. It was inferred that the strength of the compound layer determines fatigue strength.