Search Results

The piston rings, the engine sliding parts, are required to further contribute on mechanical loss reduction in order to improve fuel efficiency. However, many cases of the abnormal combustion due to oil upward flow, as well as the increase in oil consumption have been reported. Therefore, elucidation of the mechanism of those phenomena is still an urgent task. It is widely known that the distribution of the sliding face pressure in between the piston ring and the cylinder bore largely influence the oil flow via the sliding face of the piston ring. However, there are many unknown aspects in this field. Therefore, verification of the sliding face pressure during the actual operation is necessary in order to elucidate the mechanism of oil consumption. The thin-film sensor, since it has little influence on shape, is widely used as a measurement method of the sliding face pressure between two different faces, however this method has never been applied to the piston ring in the past.

Hydrogen ICE can achieve carbon neutrality and is adaptable to medium and heavy-duty vehicles, for which electricity is not always a viable option. It can also be developed using high-quality conventional diesel/gasoline engine technology. Furthermore, it allows for the conversion of existing engines to hydrogen ICE, making it highly marketable. The reliability and durability of MPI hydrogen ICE is better than that of DI, and MPI has an advantage over DI in terms of cruising range because the low-pressure injection of hydrogen reduces the remaining hydrogen in the tank. Improving MPI output is, however, an important subject, and achieving this requires suppressing abnormal combustion such as pre-ignition. In this study, an inline four-cylinder 5L turbo-charged diesel engine was converted to a hydrogen engine. Hydrogen injectors were installed in the intake ports and spark plugs were installed instead of diesel fuel injectors.

The reduction of friction losses is a subject of central importance in a diesel engine. The piston frictions of low viscosity engine oil and molybdenum dialkyl dithiocarbamate (MoDTC) have been measured by floating liner method. It was found that the low viscosity engine oil lower than 5W-30 is not effective against the reduction of friction mean effective pressure (FMEP) related to the fuel consumption. MoDTC showed a good performance against the reduction of FMEP. In the friction measurement points, the reduction ratio of 10W-30 with MoDTC to 10W-30 was greater than that of 5W-30 to 10W-30.

The friction reduction of a piston/piston-ring assembly is effective for fuel economy of an engine, and a friction measurement method is required for developing low friction pistons, piston-rings and lubricants. Most suitable method for friction measurement for piston assemblies is “floating liner method”. It has load sensors between a floating cylinder liner and cylinder block, and the sensors can detect friction force acting on the liner. Many apparatuses using floating liner method are developed. They are roughly divided to two categories. In one of them, floating liner is supported by load-washers which axis is set parallel to the center line of the cylinder liner. In another type, floating liner is supported by three-component force sensors installed on the side face of the cylinder. In this paper, five types of floating liner devices were compared.

Clarifying the mechanism of oil transporting upward at around an oil ring of a piston is necessary for calculating engine oil consumption. This study aimed to clarify the function of oil drain holes in the oil ring groove of a piston. The effect of the oil drain holes in the groove on oil consumption was investigated. Also the pressure balance around the oil ring was measured. It was found that the drain holes in the groove lowered oil consumption. It was assumed that lower pressure in the groove with the drain holes caused less oil flow into the third land.

Downsizing and slowing down of engine speed reduce mechanical losses and improve fuel economy. However, they exacerbate lubrication condition. The oil film thickness of the bearing of the small end of the connecting rod, which was one of the sliding surfaces with the severest lubrication condition in a diesel engine, was measured in this study to clarify the lubrication condition. Optical fibers were embedded in the bearing, and oil film was measured by means of the laser induced fluorescence method. It was found that oil film thickness was affected combustion gas pressure and distortion of the piston pin.

The specific output of 4-cycle engines are generally smaller than that of 2-cycle engines. Increasing engine speed is one method to improve the specific output, however, it contains some disadvantages in application. Hence, improvement in torque with the 4-cycle engine is desirable. Although torque could be improved by super-charging, it seems difficult to apply existing systems for small displacement engines due to problems of their size and cost. We have, therefore, newly developed a super-charging system named Advanced Crankcase Super Charge (hereinafter referred to as ACSC) using a crankcase as a supercharger. In this study, we made a 50cc single cylinder prototype engine with ACSC and carried out the engine unit tests and actual running tests on a scooter. From these tests, the torque that is twice as that of the naturally aspirated engine was obtained.

Connecting rod design factors, such as geometric shape, capscrew torque and materials can significantly affect bore distortion and assembly stress. In this paper, experiments using different materials were conducted on several connecting rod big-ends with various shapes, bosses and bolts. The results show that the distortion of the big-end bore and the bolt stress are influenced considerably by the big-end shape, the bolt axial tension and the material under inertia force. It was also observed that the bolt bending stress and the load separating the big-end joint surface could be calculated with high accuracy using three-dimensional FEM in the initial connecting rod design.

Reduction in the cycle-to-cycle variation (CCV) of combustion in internal combustion engines is required to reduce fuel consumption, exhaust emissions, and improve drivability. CCV increases at low load operations and lean/dilute burn conditions. Specifically, the factors that cause CCV of combustion are the cyclic variations of in-cylinder flow, in-cylinder distributions of fuel concentration, temperature and residual gas, and ignition energy. However, it is difficult to measure and analyze these factors in a production engine. This study used an optically accessible single-cylinder engine in which combustion and optical measurements were performed for 45 consecutive cycles. CCVs of the combustion and in-cylinder phenomena were investigated for the same cycle. Using this optically accessible engine, the volume inside the combustion chamber, including the pent-roof region can be observed through a quartz cylinder.

Cycle-to-cycle variation (CCV) of combustion in low load operation is a factor that may cause various problems in engine operation. Variable valve timing and variable ignition timing are commonly used as a means to reduce this variation. However, due to mountability and cost constraints, these methods are not feasible for use in motorcycle engines. Therefore, development of an engine with minimal CCV without utilizing complicated mechanisms or electronic control is required. CCV of combustion may be caused by fluctuations in in-cylinder flow, air-fuel mixture, temperature, residual gas and ignition energy. In this study, the relationship between CCV of combustion, in-cylinder flow fluctuation and air-fuel mixture fluctuation was the primary focus. In order to evaluate in-cylinder flow fluctuation, Time Resolved Particle Image Velocimetry (TR-PIV) technique was utilized.

Regarding S.I. gasoline engine, it is one of the most important matters to eliminate cyclic variation of combustion. Especially with high compression ratio and high boosted engine, the difficulties increase more. This paper describes the analysis of combustion process precisely by using many ion-current probes and CFD with the unique approaches. The number of used ion-current probes is 80 and they are mounted on whole combustion chamber wall especially including moving intake and exhaust valve faces. Thus cyclic variations of flame propagation can be measured precisely under high compression ratio and high boosted conditions in a multi-cylinder engine. In addition, CFD combustion simulation is conducted through full four strokes of continuous nine cycles. Moreover air motion and pressure vibration in intake and exhaust manifolds in whole cycles are considered. These unique approaches have made CFD result correspond to the measurement result of cyclic variations of actual combustion.

Reducing friction in the crankshaft main bearings is an effective means of improving the fuel efficiency of reciprocating internal combustion engines. To realize these improvements, it is necessary to understand the lubricating conditions, in particular the oil film pressure distributions between crankshaft and bearings. In this study, we developed a thin-film pressure sensor and applied it to the measurement of engine main bearing oil film pressure in a 4-cylinder, 2.5 L gasoline engine. This thin-film sensor is applied directly to the bearing surface by sputtering, allowing for measurement of oil film pressure without changing the shape and rigidity of the bearing. Moreover, the sensor material and shape were optimized to minimize influence from strain and temperature on the oil film pressure measurement. Measurements were performed at the No. 2 and 5 main bearings.

The behavior of the liquid in the motorcycle fuel tank is an interesting theme from the viewpoint of the fuel meter construction, as effected by variance in the fuel pressure resulting from acceleration or deceleration, etc. It can be assumed that the behavior of the liquid in the fuel tank will be affected by the running pattern, the shape and capacity of the fuel tank, etc. Here is a report on an experiment recently made to observe how the liquid behaves in a partially fully enclosed tank. We simplified the tank shape and the involved conditions (to actually observe the behavior of the inside liquid by the suspension method.) Then we have analized the effectes according to different liquid containers, to different velocities, and to different liquid volumes as well as the time history variance in the internal pressure.

We focus on the control issue for engine systems from the perspective of chaos theory, which is based on the fact that engine systems have a low-dimensional chaotic dynamics. Two approaches are discussed: controlling chaos and harnessing chaos, respectively. We apply Pyragas' chaos control method to an actual engine system. The experimental results show that the chaotic motion of an engine system may be stabilized to a periodic motion. Alternatively, harnessing chaos for engine systems is addressed, which regards chaos as an essential dynamic mode for the engine.

In four-cycle single-cylinder motorcycle engines, high Hertzian stress is generated on and beneath the big-end surface of the connecting rod. If the surface strength would be improved, the diameter of the big-end could be made smaller, making the entire engine smaller and lighter. Therefore, application of carbide dispersion carbonitriding using a vacuum furnace (hereinafter referred to as “vacuum CD carbonitriding”) on the big-end surface was investigated. Vacuum CD carbonitriding was carried out by three processes. The first was a CD carburizing process. This process is done to obtain granular cementite, but in order to avoid decreasing the strength, it is necessary to prevent the formation of coarsened cementite at the grain boundary. The second process was a refining process. This process is done for the purpose of refining the prior austenite grain size. The third process was a carbonitriding process.

The authors have previously proposed a plume ignition and combustion concept (i.e., PCC combustion), in which a hydrogen fuel is directly injected to the combustion chamber in the latter half of compression stroke and forms a richer mixture plume. By combusting the plume, both cooling losses and NOx formation are reduced. In this study, thermal efficiency was substantially improved and NOx formation was reduced with PCC combustion by optimizing such characteristics as direction and diameter of the jets in combination with combustion of lean mixture. Output power declined due to the lean mixture, however, was recovered by supercharging while keeping NOx emissions at the same level. Thermal efficiency was further improved by slightly re-optimizing the jet conditions.

The mechanism of lubricant dilution by post injection fuel in a diesel engine was investigated. The operating conditions of the engine were changed, and oil was sampled from each part of the piston and the crankcase, and the dilution ratio was analyzed. Also, photochromism was used to visualize the oil and fuel flow. Dilution ratios obtained from oil sampling and photochromism showed the same tendency.

In order to obtain more reduction of two-stroke motorcycle engine noise than usual, it becomes necessary to make improvements within the combustion process itself. This study was carried out for two objectives. One is the investigation of the relationship between combustion and noise, and the other one is the development of noise reduction techniques. As the result, it was discovered that there was a significant correlation between engine noise and (dP/dθ)max, called the maximum rate of cylinder pressure rise. Therefore, the reduction of the (dP/dθ) max was recognized to be effective for engine noise reduction. The optimized alteration of combustion chamber shape is the most effective noise reduction technique, because it is able to reduce (dP/dθ) max without any sacrifice of engine power. In fact, the level of noise reduction can be predicted by one of the parameters obtained from the combustion chamber shape.

In order to verify cooling loss reduction effect of internal combustion engine, method for measuring wall surface temperature and heat flux with high accuracy is required. Various methods have been proposed for measuring the cooling loss from the combustion gas to the combustion chamber wall, newly coaxial type thin-film temperature sensor was developed for wall temperature and heat flux measurement by the authors. This sensor consists of thin-film and body and center wire have three junction positions in the case where three materials are different. Therefore, it is necessary to use the same materials for thin-film and body or thin-film and center wire to make two junction points. In this study, sputtering method that can be formed various kinds of alloy materials and film thickness of 0.1~1μm on the sensor surface was chosen.

The fracture splitting (FS) method for case hardened connecting rods has been developed to improve engine performance while decreasing production costs. The FS method is widely used for automotive connecting rods because it effectively improves their productivity. Normalized forging steels, microalloyed forging steels and powder metals have generally been used as the material in the FS method as they are easily split due to their brittleness. On the other hand, the materials to be used for high performance motorcycles are case hardened low carbon steels because they allow the connecting rods to be lightweight due to their high fatigue strengths. These materials, which have a hardened area of approx. 0.5mm in depth from the surface, have a ductile texture inside. This texture obstructs the crack propagation and makes the split force too high to split without deforming the bearing area.