Search Results

Due to the continuously increasing number of electronic control units (ECUs) in modern cars, and their growing complexity, automated tests not only of single ECUs but also of interconnected ECUs have become an important step in the development of automotive electronics. These tasks require new test systems. This paper describes the problems engineers face when developing and testing today's car electronics, as well as a high-end hardware-in-the-loop (HIL) tool set (hardware, software, models) applied to the testing of four networked ECUs for engine management, vehicle dynamics control, automatic transmission, and an active suspension system. The tool set comprises general features needed for HIL tests, like automated code generation for real-time models using MATLAB/Simulink and a comprehensive set of dedicated hardware (processor and I/O hardware).

In order to achieve high customer satisfaction and to avoid high warranty costs caused by component failures of the power-train of hybrid electric vehicles (HEV), car manufacturers have to optimize the dimensioning of these elements. Hence, it is obligatory for them to gain knowledge about the different types of vehicle usage being predominant all over the world. Therefore, in this paper we present a Data Mining system that employs a Random Forest (RF) based dissimilarity measure in the dimensionality reduction technique t-Distributed Stochastic Neighbor Embedding (t-SNE) to automatically identify and visualize different types of vehicle usage by applying these methods to aggregated logged on-board data, i.e., load spectrum data. This kind of data is calculated and recorded directly on the control units of the vehicles and consists of aggregated numerical data, like the histogram of the velocity signal or the traveled distance of a vehicle.

Model-based software development is increasingly being used to develop software for electronic control units (ECUs). When developing safety-related software, compared to non-safety-related software development, additional requirements specified by relevant safety-standards have to be met. Meeting these requirements should also be considered to be best practices for non-safety-related software. This paper introduces a model-based reference workflow for the development of safety-related software conforming to relevant safety-standards such as IEC 61508 and ISO 26262. The reference workflow discusses requirements traceability aspects, software architecture considerations that help to support modular development and ease the verification of model parts and the code generated from those model parts, and the selection and enforcement of modeling and coding guidelines.

Automotive manufacturers and suppliers of electronic control units (ECUs) will be challenged more and more in the future to reduce costs and the time needed for ECU development. At the same time, increasing requirements concerning exhaust gas emissions, drivability, onboard diagnostics and fuel consumption have led to the growing complexity of modern engines and the associated management systems. As a result, the number and complexity of control parameters and look-up tables in the ECU software is increasing dramatically. Thus, in powertrain applications especially, calibration development has become a time-consuming and cost-intensive stage in the overall ECU development process. This paper describes the current situation in calibration development and shows how the new dSPACE Calibration System will face this situation. It provides an overview of the main benefits of the tool, which has been designed in close cooperation with calibration engineers.

Due to the rapidly increasing number of electronic control units (ECUs) in modern vehicles, software and ECU testing plays a major role within the development of automotive electronics. To ensure effective as well as efficient testing within the whole development process, a seamless transition in terms of the reusability of tests and test data as well as powerful and efficient means for developing and describing tests are required. This paper therefore presents a new integration approach for modern test development and test management. Besides a very easy-to-use way of describing tests graphically, the main focus of the new approach is on the management of a large number of tests, test data, and test results, allowing close integration into the automotive development processes.

In this paper a new numerical methodology to compute component temperatures of a rotating cardan shaft is described. In general temperatures of the cardan shaft are mainly dominated by radiation from the exhaust gas system and air temperatures in the transmission tunnel and underbody. While driving the cardan shaft is rotating. This yields a uniform temperature distribution of the circumference of the shaft. However most simulation approaches for heat protection are nowadays steady-state computations. In these simulations the rotation of the cardan shaft is not considered. In particular next to the exhaust gas system the distribution of the temperatures of the cardan shaft is not uniform but shows hot temperatures due to radiation at the side facing the exhaust gas system and lower temperatures at the other side. This paper describes a new computational approach that is averaging the radiative and convective heat fluxes circumferentially over bands of the cardan shaft.

Automotive technology is rapidly changing with electrification of vehicles, driver assistance systems, advanced safety systems etc. This advancement in technology is making the task of validation and verification of embedded software complex and challenging. In addition to the component testing, integration testing imposes even tougher requirements for software testing. To meet these challenges dSPACE is continuously evolving the Hardware-In-the-Loop (HIL) technology to provide a systematic way to manage this task. The paper presents developments in the HIL hardware technology with latest quad-core processors, FPGA based I/O technology and communication bus systems such as Flexray. Also presented are developments of the software components such as advanced user interfaces, GPS information integration, real-time testing and simulation models. This paper provides a real-world example of implication of integration testing on HIL environment for Chassis Controls.

The technological development in the field of automotive electronics is proceeding at almost break-neck speed. The functions being developed and integrated into cars are growing in complexity and volume. With the increasing number and variety of sensors and actuators, electronics have to handle a greater amount of data, and the acquisition and generation of I/O signals is also growing in complexity, for example, in engine management applications. Moreover, intelligent and complex algorithms need to be processed in a minimum of time. This all intensifies the need for Rapid Control Prototyping (RCP), a proven method of decisively speeding up the model-based software development process of automotive electronic control units (ECUs) [1],[2]. All these demanding tasks, including connecting sensors and actuators to the RCP system, need to be performed within a standard prototyping environment.

Hardware-in-the-loop (HIL) testing is used by commercial vehicle original equipment manufacturers (OEMs) in several fields of electronics development. HIL tests are a part of the standard development process for engine and machine control systems. For electronic control units (ECUs), not only the HIL test of the hardware but also the controller software validation is very important. For hardware diagnostics validation, a dynamic simulation of the real system could be omitted and an open-loop test of the controller is sufficient in most cases. For most controller software validation including OBD (on-board diagnosis) tests, detailed but real-time capable models have to be used. This article describes the needs and challenges of models in hardware-in-the-loop (HIL) based testing, taking into account the wide range of commercial and off-highway vehicles.

Air spring systems gain more and more popularity in the automotive industry and with the ever growing demand for comfort nowadays they are almost inevitable. Some significant advantages over conventional steel springs are appealing for commercial vehicles as well as for the modern passenger vehicles in the luxury class. Current production air spring systems exist in combination with hydraulic shock absorbers (integrated or resolved). An alternative is to use the medium air not only as a spring but also as a damper: a so-called air spring air damper. Air spring air dampers are force elements which could be a great step for the chassis technology due to their functionality (frequency selectivity, load levelling, load independent vibration behaviour, load dependent damping). Some of their design which avoid dynamic seals by the using of rubber bellows contribute to a better ride comfort.

The development of perception functions for tomorrow’s automated vehicles is driven by enormous amounts of data: often exceeding a gigabyte per second and reaching into the terabytes per hour. Data is typically gathered by a fleet of dozens of mule vehicles which multiply the data generated into the hundreds of petabytes per year. Traditional methods for fueling data-driven development would record every bit of every second of a data logging drive on solid-state drives located on a PC in the vehicle. Recorded data must then be exported from these drives using an upload station which pushes to the data lake after arriving back at the garage. This paper considers different techniques for curating logged data.

Due to the diversity of Heavy Duty Vehicles (HDV), the European CO2 and fuel consumption monitoring methodology for HDVs will be based on a combination of component testing and vehicle simulation. In this context, one of the key input parameters that need to be accurately defined for achieving a representative and accurate fuel consumption simulation is the vehicle's aerodynamic drag. A highly repeatable, accurate and sensitive measurement methodology was needed, in order to capture small differences in the aerodynamic characteristics of different vehicle bodies. A measurement methodology is proposed which is based on constant speed measurements on a test track, the use of torque measurement systems and wind speed measurement. In order to support the development and evaluation of the proposed approach, a series of experiments were conducted on 2 different trucks, a Daimler 40 ton truck with a semi-trailer and a DAF 18 ton rigid truck.

Securing the desired strength and durability characteristics of suspension components is one of the most important topics in the development of commercial vehicles because these components undergo multiaxial variable amplitude loading. Leaf springs are essential for the suspension systems of trucks and they are considered as security relevant components in the product development phase. In order to guide the engineers in the design and testing department, a simulation method is developed as explained by Bakir et al. in a recently published SAE paper [1]. The main aim of the present study is to illustrate the validation of this simulation method for the durability of leaf springs based on the results from testing and measurements. In order to verify this CAE Method, the calculated stresses on the leaf springs are compared with the results of strain gage measurements and the fatigue failures of leaf springs are correlated with the calculated damage values.

Model-based software development and automatic code generation have become increasingly established in recent years. The automotive industry has widely adopted and successfully deployed these methods in many different series production programs worldwide. This brought various benefits, such as a reduction in development times, improved quality due to more precise specifications, and early verification and validation by means of simulation. At the same time, more and more safety-related and safety-critical systems have been - and will be -introduced into modern vehicles. Common examples are active front steering, adaptive cruise-control, and integrated chassis control. This leads to the question, if and how model-based design and automatic production code generation can be applied to the development of safety-critical systems.

Today, hardware-in-the-loop (HIL) simulation is common practice as a testing methodology for electronic control units (ECUs). An essential criterion for the efficiency of an HIL system is the availability of powerful test automation having access to all of its hardware and software components (including I/O channels, failure insertion units, bus communication controllers and diagnostic interfaces). The growing complexity of vehicle embedded systems, which are interconnected by bus systems (like CAN, LIN or FlexRay), result in hundreds or even thousands of tests that have to be done to ensure the correct system functionality. This is best achieved by automated testing. Automated testing usually is performed by executing tests on a standard PC, which is interconnected to the HIL system. However, higher demands regarding timing precision are hard to accomplish. As an example, ECU interaction has to be captured and responded to in the range of milliseconds.

This paper describes a new production code generator that meets both the requirements of code developers for efficient and reliable production code, as well as the desire of system engineers to establish a control design process based on simulation models that double as executable specifications for the ECU software. The production code generator supports automatic scaling, generates optimized fixed-point C code for microcontrollers like the Motorola 683xx, Siemens C16x, and Hitachi SH-2, and produces ASAP2 [1] calibration information. Benchmark results show that the autogenerated code can match or even exceed the efficiency of typical handwritten production code. Code quality is assured by design and by systematic, automatic, and extremely comprehensive test procedures.

This paper will first introduce and classify the basic principles of architecture-driven software development and will briefly sketch the presumed development process. This background information is then used to explain extensions which enable current behavior modeling and code generation tools to operate as software component generators. The generation of AUTOSAR software components using dSPACE's production code generator TargetLink is described as an example.

While the market share for diesel engines for LD vehicles in Europe has grown continuously in the past years, the market share in North America is still negligible. Until now, it has been possible to fulfill the limits for nitrogen oxides (NOx) both in Europe and in North America by engine measures alone, without using an active NOx aftertreatment system. With the introduction of Tier II Bin 8 and Tier II Bin 5 emissions legislation in the US in 2007, most new diesel applications will now require NOx aftertreatment. One of the possible technologies for the reduction of nitrogen oxides in lean exhaust gas is the NOx storage catalyst which has become the generally-accepted choice for engines with gasoline direct injection systems and which is also utilized in the current diesel Bluetec I systems from Daimler. For heavier applications urea-SCR is the preferred technology to fulfill NOx legislation limits.

An overview of Daimler?s progression to advance powertrain technology in a growth industry shows many different solutions to improvement in transportation. Daimler continues to make breakthroughs in technology development and application building on 125 years of automotive development. Optimization of current powertrains will enable a significant gain in CO2/mi reductions, that dependent on product mix can be augmented with additional technologies. There is however no bypass to some form of electrification, enabling efficiency gains and alternative forms of power supply. Development of hybrid powertrains continues in an established manner and enhanced development of further electrified powertrains are in development. Organizationally and technically, significant skills and adjustments need to continue to be undertaken enabling OEMs and in particular the supply base to develop optimized solutions efficiently. The outlook is bright for novel component development and innovation.

NH₃/urea SCR is a very effective and widely used technology for the abatement of NOx from diesel exhaust. The SCR mechanism is well understood and the catalyst behavior can be predicted by mathematical models - as long as operation above the temperature limit for AdBlue® injection is considered. The behavior below this level is less understood. During the first seconds up to minutes after cold start, complete NOx abatement can be observed over an SCR catalyst in test bench experiments, together with a significant increase in temperature after the converter (ca. 100 K). In this work these effects have been investigated over a monolith Cu-zeolite SCR catalyst. Concentration step experiments varying NO, NO₂ and H₂O have been carried out in lab scale, starting from room temperature. Further, the interaction of C₃H₆ and CO with NOx over the SCR has been investigated.