Search Results

This document is for establishing tire removal criteria of on-wing civil aircraft tires only. This document is primarily intended for use with commercial aircraft, but may be used on other categories of civil aircraft, as applicable. The criteria are harmonized with the Care and Service Manuals of the tire manufacturers for both radial and bias tires.

This document is for establishing tire removal criteria of on-wing civil aircraft tires only. This document is primarily intended for use with commercial aircraft but may be used on other categories of civil aircraft as applicable. The criteria are harmonized with the Care and Service Manuals of the tire manufacturers for both radial and bias tires.

This SAE Aerospace Information Report (AIR) describes the current process for performing comparative wear testing on aircraft tires in a laboratory environment. This technique is applicable to both radial and bias tires, and is pertinent for all aircraft tire sizes. This AIR describes a technique based upon “wear” energy. In this technique, side wear energy and drag wear energy are computed as the tire is run through a prescribed test program. The specifics that drive the test setup conditions are discussed in Sections 4 through 7. In general, the technique follows this process: A test profile is developed from measured mechanical property data of the tires under study. Each tire is repeatedly run to the test profile until it is worn to the maximum wear limit (MWL). Several tires, typically 5 to 10, of each tire design are tested. Wear energy is computed for each test cycle and then summed to determine total absorbed wear energy. An index is calculated for each tire design.

This specification covers the recommended design, construction, performance and testing requirements for aircraft wheel inflation valves incorporating an inflation pressure gauge which are mounted on the aircraft wheel. These valve/gauge assemblies should be appropriate for use on all aircraft types supported by tubeless tire/wheel assemblies.

This specification covers the recommended design, construction, performance and testing requirements for aircraft wheel inflation valves incorporating an inflation pressure gauge which are mounted on the aircraft wheel. These valve/gauge assemblies should be appropriate for use on all aircraft types supported by tubeless tire/wheel assemblies.

This SAE Aerospace Recommended Practice (ARP) sets forth criteria for the installation, inflation, inspection, maintenance and removal of aircraft tires as well as criteria for the maintenance of the operating environment so as to achieve the purpose stated in 1.1. (Definitions of terms related to aircraft tires is found in 2.2.)

This SAE Aerospace Recommended Practice (ARP) sets forth criteria for the installation, inflation, inspection, and maintenance of aircraft tires and the maintenance of the operating environment to ensure the safety of support personnel and the safe operation of the aircraft.

This SAE Aerospace Recommended Practice (ARP) sets forth criteria for the installation, inflation, inspection, maintenance and removal of aircraft tires as well as criteria for the maintenance of the operating environment so as to achieve the purpose stated in 1.1. (Definitions of terms related to aircraft tires is found in 2.2.)

This document is for establishing and addressing anomalies on appearance of new and newly retreaded tires prior to installation on aircraft. It is intended to use cosmetics as well as functionality to make a determination of acceptability. However, if cosmetic appearance is not a requirement, use the inspection criteria from ARP6225, Aircraft Tire Removal Criteria. This ARP does not supersede (E)TSO-C62 minimum requirements including marking requirements.

The purpose of this SAE Aerospace Recommended Practice (ARP) is to establish guidelines for the measurement of static and dynamic characteristic properties of aircraft tires. It is intended as a general guide toward standard practice, but may be subject to frequent changes to keep pace with experience and technical advances. This revision (Revision A) is also intended to provide suggested guidelines for synthesizing tire dynamic data necessary for landing gear shimmy analyses.

The purpose of this SAE Aerospace Recommended Practice (ARP) is to establish guidelines for the measurement of static and dynamic characteristic properties of aircraft tires. It is intended as a general guide toward standard practice, but may be subject to frequent changes to keep pace with experience and technical advances.

The purpose of this SAE Aerospace Recommended Practice (ARP) is to establish guidelines for the measurement of static and dynamic characteristic properties of aircraft tires. It is intended as a general guide toward standard practice, but may be subject to frequent changes to keep pace with experience and technical advances. It replaces the previous SAE document, AIR1380.

This SAE Aerospace Information Report (AIR) applies to landing gear tires and airframe structure for all types and models of civil and military aircraft having tires as part of the landing gear.

This SAE Aerospace Information Report (AIR) applies to landing gear tires and airframe structure for all types and models of civil and military aircraft having tires as part of the landing gear.

This SAE Aerospace Standard (AS) establishes requirements for manufacturing, testing, identification, packaging, and quality of tubes for application in commercial and military aircraft wheel assemblies.

This SAE Aerospace Standard (AS) establishes requirements for manufacturing, testing, identification, packaging, and quality of tubes for application in commercial and military aircraft wheel assemblies.