Refine Your Search

Date

Date

Topic

Topic

Quality, Reliability, and Durability Chassis Regulations Seals and gaskets AMS K Non Destructive Methods and Processes Committee Hazardous materials

Search Results

Viewing 1 to 20 of 99
123Next >Last >>
Sort by title
Standard

Eddy Current Inspection of Circular Holes in Nonferrous Metallic Aircraft Engine Hardware
2019-10-14
CURRENT
AS4787A
This SAE Aerospace Standard (AS) establishes minimum requirements for eddy current inspection of circular holes in nonferrous, metallic, low conductivity (less than 5% IACS) aircraft engine hardware with fasteners removed. The inspection is intended to be performed at maintenance and overhaul facilities on engine run hardware.
Standard

Exposure Levels of UV Radiation in Nondestructive Inspection Processes
2019-08-05
CURRENT
AIR4964
Long wave ultraviolet or UV-A radiation (between 320 to 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. The UV-A radiation is obtained from either fluorescent or high intensity discharge lamps that are stationary or portable. The commercially available UV-A lamps possess a large variation in intensity output that can cause a legitimate concern for possible health hazard. This draft reviews the nature of UV-A radiation emitted by these lights, blacklight equipment, acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH) and the European Standards Committee for Nondestructive Testing, and recommendation of proper practices when working with UV-A radiation.
Standard

FLUORESCENT PENETRANT INSPECTION Aircraft and Engine Component Maintenance
2011-08-10
HISTORICAL
AMS2647
This specification establishes requirements, instructions, and procedures to ensure that fluorescent penetrant inspections are capable of achieving an acceptable level of defect detection on aircraft and engine components during maintenance and overhaul operations.
Standard

Fluoroscopic X-Ray Inspection
1945-08-01
HISTORICAL
AMS2650
This specification has been declared "NONCURRENT" by the Aerospace Materials Division, SAE, as of 1-1-84. It is recommended that this specification not be specified for new designs. This cover sheet should be attached to the initial issue of the sUbject specification. Noncurrent refers to those procedures which have previously been widely used and which may be required on some existing designs in the future. The Aerospace Materials Division does not recommend these as standard procedures for future use in new designs. Each of these "Noncurrent" specifications is available from SAE upon request. This specification has been CANCELLED by the Aerospace Materials Division, SAE, as of August, 1989. By this action, subject specification number and its title will be deleted from the active specification index of Aerospace Material Specifications.
Standard

Inspection Material, Penetrant
2006-10-30
HISTORICAL
AMS2644E
This specification establishes the classification, technical requirements, tests, and test procedures for the qualification, approval, and quality verification of all materials used in the liquid penetrant methods of inspection with the exception of those excluded in the application section.
Standard

Inspection Material, Penetrant
2021-04-30
WIP
AMS2644J
This specification establishes the classification, technical requirements, tests, and test procedures for the qualification, approval, and quality verification of all materials used in the liquid penetrant methods of inspection with the exception of those excluded in the application section.
Standard

Inspection Material, Penetrant
2020-07-14
CURRENT
AMS2644H
This specification establishes the classification, technical requirements, tests, and test procedures for the qualification, approval, and quality verification of all materials used in the liquid penetrant methods of inspection with the exception of those excluded in the application section.
Standard

Inspection Material, Penetrant
2013-10-17
HISTORICAL
AMS2644F
This specification establishes the classification, technical requirements, tests, and test procedures for the qualification, approval, and quality verification of all materials used in the liquid penetrant methods of inspection with the exception of those excluded in the application section.
Standard

Inspection Material, Penetrant
2019-04-08
HISTORICAL
AMS2644G
This specification establishes the classification, technical requirements, tests, and test procedures for the qualification, approval, and quality verification of all materials used in the liquid penetrant methods of inspection with the exception of those excluded in the application section.
Standard

Inspection Process, Magnetic Rubber
2009-07-10
HISTORICAL
AMSI83387A
This specification covers both the material and the examination process of an inspection material in the form of a dispersion of magnetic particles in a controlled viscosity rubber base that cures at room temperature by addition of one or more curing agents. The test object is magnetized with the uncured rubber covering the area of interest. The magnetic particles then migrate to the leakage field caused by the discontinuity. As the rubber cures, discontinuity indications remain in place on the rubber. The product may be supplied in a variety of viscosities and colors.
Standard

Inspection Process, Magnetic Rubber
2016-01-06
CURRENT
AMSI83387B
This specification covers both the material and the examination process of an inspection material in the form of a dispersion of magnetic particles in a controlled viscosity rubber base that cures at room temperature by addition of one or more curing agents. The test object is magnetized with the uncured rubber covering the area of interest. The magnetic particles then migrate to the leakage field caused by the discontinuity. As the rubber cures, discontinuity indications remain in place on the rubber. The product may be supplied in a variety of viscosities and colors.
Standard

Inspection, Ultrasonic Product Over 0.5 Inch (12.7 mm) Thick
2008-10-22
HISTORICAL
AMS2630B
This specification covers procedures for ultrasonic inspection, by pulse-echo procedures, of flat, rectangular, round, cylindrical, and contoured products having a thickness or cross-sectional dimension greater than 0.50 inch (12.7 mm), using either contact or immersion methods, and using the longitudinal-wave or shear-wave modes or combinations of the two, as necessary. This specification may apply to testing finished machined parts provided the parts can meet the basic testability requirements, such as size, contour, metallurgical structure, and thickness.
Standard

Inspection, Ultrasonic Product Over 0.5 Inch (12.7 mm) Thick
2010-01-05
HISTORICAL
AMS2630C
This specification covers procedures for ultrasonic inspection, by pulse-echo procedures, of flat, rectangular, round, cylindrical, and contoured products having a thickness or cross-sectional dimension greater than 0.50 inch (12.7 mm), using either contact or immersion methods, and using the longitudinal-wave or shear-wave modes or combinations of the two, as necessary. This specification may apply to testing finished machined parts provided the parts can meet the basic testability requirements, such as size, contour, metallurgical structure, and thickness.
Standard

Inspection, Ultrasonic Product Over 0.5 Inch (12.7 mm) Thick
2021-11-09
CURRENT
AMS2630E
This specification covers procedures for ultrasonic inspection, by pulse-echo procedures, of flat, rectangular, round, cylindrical, and contoured products having a thickness or cross-sectional dimension greater than 0.5 inch (12.7 mm), using either contact or immersion methods, and using the longitudinal-wave or shear-wave modes or combinations of the two, as necessary. This specification may apply to testing finished machined parts provided the parts can meet the basic testability requirements, such as size, contour, metallurgical structure, and thickness.
Standard

Inspection, Ultrasonic Product Over 0.5 Inch (12.7 mm) Thick
2018-08-08
HISTORICAL
AMS2630D
This specification covers procedures for ultrasonic inspection, by pulse-echo procedures, of flat, rectangular, round, cylindrical, and contoured products having a thickness or cross-sectional dimension greater than 0.5 inch (12.7 mm), using either contact or immersion methods, and using the longitudinal-wave or shear-wave modes or combinations of the two, as necessary. This specification may apply to testing finished machined parts provided the parts can meet the basic testability requirements, such as size, contour, metallurgical structure, and thickness.
123Next >Last >>
X