Refine Your Search

Date

Date

Humidity Materials handling Electronic equipment Acoustical Materials Committee Maintenance and Aftermarket

Search Results

Viewing 1 to 20 of 31
12Next >Last >>
Sort by title
Standard

HEAT INSULATION MATERIALS TEST PROCEDURE
1981-12-01
HISTORICAL
J1324_198112
This SAE Recommended Practice provides test methods for determining the characteristics of heat insulation materials. Where applicable, methods of test developed by SAE and ASTM have been referenced.
Standard

LABORATORY MEASUREMENT OF THE AIRBORNE NOISE REDUCTION OF ACOUSTICAL MATERIALS
1989-05-01
HISTORICAL
J1400_198905
This SAE Recommended Practice establishes the test procedure, facilities, and instrumentation for determining the noise reduction characteristics of materials commonly installed in ground vehicles, marine, products, and aircraft to reduce noise levels. This document is intended to provide a means of rank ordering materials by utilizing facilities that do not necessarily meet all of the acoustical requirements in ASTM E 90, Laboratory Measurements of Airborne Sound Transmission Loss of Building Partitions. Latitude is permitted in certain test conditions to allow better correlation with in-use acoustical results.
Standard

LABORATORY MEASUREMENT OF THE AIRBORNE SOUND BARRIER PERFORMANCE OF AUTOMOTIVE MATERIALS AND ASSEMBLIES
1990-05-01
HISTORICAL
J1400_199005
This SAE Recommended Practice presents a test procedure for determining the airborne sound barrier performance of materials and composite assemblies commonly installed in surface vehicles and marine products. This document is intended to provide a means of rank ordering barrier materials according to their sound transmission loss. At each test frequency the transmission loss (TL) is projected from the measured noise reduction of the test specimen using a correlation factor (CF). The respective CF for the test condition is determined as the differences between the measured noise reduction (MNR) of a homogeneous limp panel, such as lead, and its calculated field-incidence transmission loss. Latitude is permitted in certain test conditions that do not necessarily conform to all of the acoustical requirements of ASTM E 90.
Standard

Laboratory Measurement of Random Incidence Sound Absorption Tests Using a Small Reverberation Room
2021-07-13
WIP
J2883
This SAE Recommended Practice describes a laboratory test procedure for measuring the random incidence sound absorption performance of a material or a part in a small size reverberation room by measuring decay rates. The absorption performance may include sound absorption coefficient of the test sample and or the amount of energy absorbed by the test sample. Materials for absorption treatments may include homogeneous materials, nonhomogeneous materials, or a combination of homogeneous, nonhomogeneous, and/or inelastic impervious materials. These materials are commonly installed in the mobility products and in the transportation systems such as ground vehicles, marine products, aircraft, and commercial industry (in industrial and consumer products) to reduce reverberant sound build-up and thus reduce the noise level in the environment by minimizing reflections off of hard surfaces.
Standard

Laboratory Measurement of Random Incidence Sound Absorption Tests Using a Small Reverberation Room
2020-03-04
CURRENT
J2883_202003
This SAE Recommended Practice describes a laboratory test procedure for measuring the random incidence sound absorption performance of a material or a part in a small size reverberation room by measuring decay rates. The absorption performance may include sound absorption coefficient of the test sample and or the amount of energy absorbed by the test sample. Materials for absorption treatments may include homogeneous materials, nonhomogeneous materials, or a combination of homogeneous, nonhomogeneous, and/or inelastic impervious materials. These materials are commonly installed in the mobility products and in the transportation systems such as ground vehicles, marine products, aircraft, and commercial industry (in industrial and consumer products) to reduce reverberant sound build-up and thus reduce the noise level in the environment by minimizing reflections off of hard surfaces.
Standard

Laboratory Measurement of Random Incidence Sound Absorption Tests Using a Small Reverberation Room
2015-04-30
HISTORICAL
J2883_201504
This SAE Recommended Practice describes a laboratory test procedure for measuring the random incidence sound absorption performance of a material or a part in a small size reverberation room by measuring decay rates. The absorption performance may include sound absorption coefficient of the test sample and or the amount of energy absorbed by the test sample. Materials for absorption treatments may include homogeneous materials, nonhomogeneous materials, or a combination of homogeneous, nonhomogeneous, and/or inelastic impervious materials. These materials are commonly installed in the mobility products and in the transportation systems such as ground vehicles, marine products, aircraft, and commercial industry (in industrial and consumer products) to reduce reverberant sound build-up and thus reduce the noise level in the environment by minimizing reflections off of hard surfaces.
Standard

Laboratory Measurement of the Acoustical Performance of Body Cavity Filler Materials
2017-08-11
CURRENT
J2846_201708
This SAE Recommended Practice describes a laboratory test procedure for measuring the acoustical performance of a system consisting of a body cavity filler material formed into a rectangular cross-section channel. Materials for this test may include both heat reactive and chemically reactive products, with or without a shelf to simulate a baffle in an application, or a combination of body cavity filler and aluminum foil to enhance the performance. These materials are commonly installed in transportation systems such as ground vehicles, and thus reduce the noise propagation through the rails, rockers, and pillar/posts. This document is intended to rank order the acoustical performance of materials for application on channels using general automotive steel, such that the effects of sealing of pinch welds in addition to the material could be easily evaluated.
Standard

Laboratory Measurement of the Acoustical Performance of Body Cavity Filler Materials
2010-05-26
HISTORICAL
J2846_201005
This SAE Recommended Practice describes a laboratory test procedure for measuring the acoustical performance of a system consisting of a body cavity filler material formed into a rectangular cross-section channel. Materials for this test may include both heat reactive and chemically reactive products, with or without a shelf to simulate a baffle in an application, or a combination of body cavity filler and aluminum foil to enhance the performance. These materials are commonly installed in transportation systems such as ground vehicles, and thus reduce the noise propagation through the rails, rockers, and pillar/posts. This document is intended to rank order the acoustical performance of materials for application on channels using general automotive steel, such that the effects of sealing of pinch welds in addition to the material could be easily evaluated.
Standard

Laboratory Measurement of the Acoustical Performance of Body Cavity Filler Materials
2019-10-14
WIP
J2846
This SAE Recommended Practice describes a laboratory test procedure for measuring the acoustical performance of a system consisting of a body cavity filler material formed into a rectangular cross-section channel. Materials for this test may include both heat reactive and chemically reactive products, with or without a shelf to simulate a baffle in an application, or a combination of body cavity filler and aluminum foil to enhance the performance. These materials are commonly installed in transportation systems such as ground vehicles, and thus reduce the noise propagation through the rails, rockers, and pillar/posts. This document is intended to rank order the acoustical performance of materials for application on channels using general automotive steel, such that the effects of sealing of pinch welds in addition to the material could be easily evaluated.
12Next >Last >>
X