Search Results

This study involves two areas of research. The first is the finalization of the Pedestrian Crash Data Study (PCDS) in order to provide detailed information regarding the vehicle/pedestrian accident environment and how it has changed from the interim PCDS information. The pedestrian kinematics, injury contact sources, and injuries were analyzed relative to vehicle geometry. The second area presented is full-scale attempts at reconstruction of two selected PCDS cases using the Polar II pedestrian dummy to determine if the pre-crash motion of the pedestrian and vehicle could somehow be linked to the injuries and vehicle damage documented in the case.

This paper presents a methodology for validating vehicle stability and control computer simulations. Validation is defined as showing that, within some specified operating range of the vehicle, a simulation's predictions of a vehicle's responses agree with the actual measured vehicle's responses to within some specified level of accuracy. The method uses repeated experimental runs at each test condition to generate sufficient data for statistical analyses. The acquisition and reduction of experimental data, and the processing path for simulation data, are described. The usefulness of time domain validation for steady state and slowly varying transients is discussed. The importance of frequency domain validation for thoroughly validating a simulation is shown. Both qualitative and quantitative methods for the comparison of the simulation predictions with the actual test measurements are developed.

Investigators of vehicular incidents often seek to recover data stored within on-board computer systems. For commercial vehicles, the primary source for this information is the engine control module (ECM). The data stored in these modules, not unlike passenger vehicles, varies widely among manufacturers, as do the hardware and software required to recover such data. Further, the options, and associated risks, involved with attempting to recover this data has a similarly wide variance relative to the engine manufacturer, incident related circumstances, and the tools currently available to perform such downloads. There are two primary paths available to obtain this data: (1) via the vehicle data bus (e.g. SAE J1939 or J1708 ) or (2) direct-to-module (DTM) connection. When using the DTM method, power is applied to an ECM, and the module measures the various engine control and monitoring components for validity.

During Phase VI of the National Highway Traffic Safety Administration's (NHTSA) Light Vehicle Rollover Research Program, three of the twenty-six light vehicles tested exhibited significant response asymmetries with respect to left versus right steer maneuvers. This paper investigates possible vehicle asymmetric characteristics and unintended inputs that may cause vehicle asymmetric response. An analysis of the field test data, results from suspension and steering parameter measurements, and a summary of a computer simulation study are also given.

This research focuses on the development and performance of analytical models to simulate a tractor-semitrailer in straight-ahead braking. The simulations were modified and tuned to simulate full-treadle braking with all brakes functioning correctly, as well as the behavior of the tractor-semitrailer rig under full braking with selected brakes disabled. The models were constructed in TruckSim and based on a tractor-semitrailer used in dry braking performance testing. The full-scale vehicle braking research was designed to define limits for engineering estimates on stopping distance when Class 8 air-braked vehicles experience partial degradation of the foundation brake system. In the full scale testing, stops were conducted from 30 mph and 60 mph, with the combination loaded to 80,000 lbs (gross combined weight or GCW), half payload, and with the tractor-semitrailer unladen (lightly loaded vehicle weight, or LLVW).

This paper presents a feedback linearization control technique as applied to a Roll Simulator. The purpose of the Roll Simulator is to reproduce in-field rollovers of ROVs and study occupant kinematics in a laboratory setting. For a system with known parameters, non-linear dynamics and trajectories, the feedback linearization algorithm cancels out the non-linearities such that the closed-loop dynamics behave in a linear fashion. The control inputs are computed values that are needed to attain certain desired motions. The computed values are a form of inverse dynamics or feed-forward calculation. With increasing system eigenvalue, the controller exhibits greater response time. This, however, puts a greater demand on the translational actuator. The controller also demonstrates that it is able to compensate for and reject a disturbance in force level.

An existing tire model was investigated for additional normal load-dependent characteristics to improve the large truck simulations developed by the National Highway Traffic Safety Administration (NHTSA) for the National Advanced Driving Simulator (NADS). Of the existing tire model coefficients, plysteer, lateral friction decay, aligning torque stiffness and normalized longitudinal stiffness were investigated. The findings of the investigation led to improvements in the tire model. The improved model was then applied to TruckSim to compare with the TruckSim table lookup tire model and test data. Additionally, speed-dependent properties for the NADS tire model were investigated (using data from a light truck tire).

The goal of this research was to find vehicle characteristics which may contribute to steering maneuver induced rollover accidents. This work involved studying vehicle handling dynamics using the Vehicle Dynamics Analysis, Non-Linear (VDANL) computer simulation. The simulation was used to predict vehicle responses while performing 28 different steering induced maneuvers for each of 51 vehicles. Various measures of vehicle response (metrics), such as response times, percent overshoots, etc., were computed for each vehicle from simulation predictions. These vehicle directional response metrics were analyzed in an attempt to identify vehicle characteristics that might be good predictor/explanatory variables for vehicle rollover propensity. The metrics were correlated, using the Statistical Analysis System (SAS) software and logistic regression, with single vehicle accident data from the state of Michigan for the years 1986 through 1988.

Bobtail testing data published in the literature are limited and the difference in deceleration of a bobtail configuration compared to a tractor-trailer has not been fully evaluated in the past. The authors seek to increment and update previous research on the topic. This paper presents detailed braking characteristic information obtained from full scale instrumented testing of a bobtail vehicle at various speeds. Brake timing is analyzed for the tested condition to determine the overall braking characteristics. The findings of this study are compared to 1) other testing performed with the same tractor configured with a trailer at different loading conditions and 2) to results published in literature for both bobtail vehicles and other loading conditions for both 6×4 and 4×2 tractor axle configurations.

The timing and associated levels of braking between initial brake pedal application and actual maximum braking at the wheels for a tractor-semitrailer are important parameters in understanding vehicle performance and response. This paper presents detailed brake timing information obtained from full scale instrumented testing of a tractor-semitrailer under various conditions of load and speed. Brake timing at steer, drive and semitrailer brake positions is analyzed for each of the tested conditions. The study further seeks to compare the full scale test data to predicted response from detailed heavy truck computer vehicle dynamics simulation models available in commercial software packages in order to validate the model's brake timing parameters. The brake timing data was collected during several days of full scale instrumented testing of a tractor-semitrailer performed at the Transportation Research Center, in East Liberty, Ohio.

This paper presents the details of the model for the physical steering system used on the National Advanced Driving Simulator. The system is basically a hardware-in-the-loop (steering feedback motor and controls) steering system coupled with the core vehicle dynamics of the simulator. The system's torque control uses cascaded position and velocity feedback and is controlled to provide steering feedback with variable stiffness and dynamic properties. The reference model, which calculates the desired value of the torque, is made of power steering torque, damping function torque, torque from tires, locking limit torque, and driver input torque. The model also provides a unique steering dead-band function that is important for on-center feel. A Simulink model of the hardware/software is presented and analysis of the simulator steering system is provided.

A test procedure that rates brake performance must control variability so that measured differences between vehicles are real. Tests were conducted using standard brake test procedures with three drivers in three cars on wet and dry asphalt with the ABS working and disabled. The differences between vehicles were greater than differences due to ABS condition, surface condition, and drivers. The procedure measured differences between all the vehicles with statistical certainty but used many replications and drivers. If only large differences in performance need to be distinguished, fewer replications and drivers will be needed.

This paper describes the development and implementation of an accurate and repeatable path-following algorithm focused ultimately on vehicle testing. A compact, lightweight, and portable hardware package allows easy installation and negligible impact on the vehicle mass, even for the smallest automobile. Innovative features include the ability to generate a smooth, evenly-spaced path vector regardless the quality of the given path. The algorithm proposed in this work is suitable for testing in a controlled environment. The system was evaluated in simulation and performed well in road tests at low speeds.

Heavy trucks are involved in many accidents every year and Electronic Stability Control (ESC) is viewed as a means to help mitigate this problem. ESC systems are designed to reduce the incidence of single vehicle loss of control, which might lead to rollover or jackknife. As the working details and control strategies of commercially available ESC systems are proprietary, a generic model of an ESC system that mimics the basic logical functionality of commercial systems was developed. This paper deals with the study of the working of a commercial ESC system equipped on an actual tractor trailer vehicle. The particular ESC system found on the test vehicle contained both roll stability control (RSC) and yaw stability control (YSC) features. This work focused on the development of a reliable RSC software model, and the integration of it into a full vehicle simulation (TruckSim) of a heavy truck.

For some vehicle dynamics applications, an estimate of a vehicle's center of gravity (cg) height and mass moments of inertia can suffice. For other applications, such as vehicle models and simulations used for vehicle development, these values should be as accurate as possible. This paper presents several topics related to inertial parameter estimation and measurement. The first is a simple but reliable method of estimating vehicle mass moment of inertia values from data such as the center of gravity height, roof height, track width, and other easily measurable values of any light road vehicle. The second is an error analysis showing the effect, during a simple static cg height test, of vehicle motion (relative to the support system) on the vehicle's calculated cg height. A method of accounting for this motion is presented. Similarly, the effects of vehicle motion are analyzed for subsequent mass moment of inertia tests.

A single-vehicle crash involving an SUV led to the study of the failure of the anti-sway bar linkage and tire pressure and their relative effects on the handling characteristics of the vehicle. The SUV, having been involved in a rollover, was found with the anti-sway bar drop link disconnected from the suspension lower A-arm assembly. Also, after the crash, the tire pressure in the front tires on the subject vehicle was measured to be above the value specified by the SUV manufacturer; however, the pressure for one of the rear tires was measured to be roughly half of the SUV manufacturer’s recommended pressure. The other rear tire was deflated. The testing described herein addresses the question of what effects the anti-sway bar drop link disconnection or reduced rear axle tire pressure would have on the SUV’s pre-accident handling and driveability.

This paper presents the results of an in-depth study of the measurement of occupant kinematic response on the S-E-A Roll Simulator. This roll simulator was built to provide an accurate and repeatable test procedure for the evaluation of occupant protection and restraint systems during roll events within a variety of occupant compartments. In the present work this roll simulator was utilized for minimum-energy, or threshold type, rollover events of recreational off-highway vehicles (ROVs). Input profiles for these tests were obtained through a separate study involving autonomous full vehicle tests [1]. During simulated roll events anthropomorphic test device (ATD) responses were measured using on-board high speed video, an optical three-dimensional motion capture system (OCMS) and an array of string potentiometers.

This paper evaluates the heavy tractor-trailer handling dynamics model used in the National Advanced Driving Simulator. The comparison between simulation and experiments were done using lane change, slowly increasing steer, pulse steer, step steer, and straight-line braking maneuvers. The paper discusses tractor-trailer instrumentation and the results of field experiments.

The paper presents an evaluation of two vehicle dynamics simulations: “Vehicle Dynamics Analysis, Non-Linear” (VDANL) from Systems Technology, Inc. and “Vehicle Dynamics Models for Roadway Analysis and Design” (VDM RoAD) from the University of Michigan Transportation Research Institute. The versions of these simulations are being developed for the Federal Highway Administration (FHWA). Working in cooperation with the FHWA, the National Highway Traffic Safety Administration's (NHTSA) Vehicle Research and Test Center (VRTC) in East Liberty, Ohio, has evaluated these simulations. An extensive vehicle parameter measurement and field testing program has been performed using a 1994 Ford Taurus to provide simulation parameters and to “benchmark” data for the simulation evaluation.

This paper describes the development of a more accurate shock absorber model in order to obtain better vehicle simulation results. Previous shock models used a single spline to represent shock force versus shock velocity curves. These models produced errors in vehicle simulations because the damper characteristics are better represented by the application of a hysteresis loop in the model. Thus, a new damper model that includes a hysteresis loop is developed using Matlab Simulink. The damper characteristics for the new model were extracted from measurements made on a shock dynamometer. The new model better represents experimental shock data. The new shock model is incorporated into two different lumped-parameter vehicle models: one is a three degree-of-freedom vehicle handling model and the other is a seven degree-of-freedom vehicle ride model. The new damper model is compared with the previous model for different shock mileages (different degrees of wear).