Refine Your Search

Search Results

Standard

CONICAL SPRING WASHERS

1998-05-01
HISTORICAL
J773_199805
This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.
Standard

Conical Spring Washers

2016-08-31
CURRENT
J773_201608
This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.
Standard

Decarburization in Hardened and Tempered Unified Threaded Fasteners

2013-01-02
CURRENT
J121_201301
This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.
Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2016-11-18
CURRENT
J1102M_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Metric Wheel Bolts

2013-04-11
HISTORICAL
J1102M_201304
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Steel Nuts

2017-07-20
CURRENT
J995_201707
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”
Standard

Mechanical and Material Requirements for Steel Nuts

2012-02-21
HISTORICAL
J995_201202
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 in, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 in, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”
Standard

Mechanical and Material Requirements for Wheel Bolts

2016-11-21
CURRENT
J1102_201611
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Material Requirements for Wheel Bolts

2013-04-11
HISTORICAL
J1102_201304
This SAE Standard covers the chemical, metallurgical, and mechanical requirements for two types of passenger car and truck wheel bolts, as follows: a Nonserrated shank bolts which are heat treated b Serrated shank bolts which are case hardened
Standard

Mechanical and Quality Requirements for Tapping Screws

1979-06-01
HISTORICAL
J933_197906
This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are covered in SAE J478.) The primary objective of the specification is to insure that screws form or cut mating threads in materials of construction into which they are normally driven, without deforming their own thread and without breaking during assembly or service. Certain limitations on basic material and manufacturing processes have been incorporated because the size and configuration of the parts under consideration make them vulnerable to relatively small variations in chemistry, heat treatment, etc., and because experience has shown that in processing it is difficult to keep these variables consistently "in balance."
Standard

Mechanical and Quality Requirements for Tapping Screws

2013-02-25
CURRENT
J933_201302
This SAE Recommended Practice covers the mechanical and quality requirements for steel tapping screws used in automotive and related industries. It does not apply to corrosion resistant (stainless) steel screws. (Dimensional requirements for most types of screws mentioned herein are covered in ASME B 18.6.4, Thread Forming and Thread Cutting Tapping Screws and Metallic Drive Screws’.)
Standard

Metric Thread Rolling Screws

2017-09-07
CURRENT
J1237_201709
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Metric Thread Rolling Screws

2001-03-12
HISTORICAL
J1237_200103
This SAE Standard covers requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Metric Thread Rolling Screws

2018-08-20
WIP
J1237
This SAE Standard covers material, dimensional, performance and test requirements for metric thread rolling screws suitable for use in general engineering applications.
Standard

Nut and Conical Spring Washer Assemblies

2013-04-15
HISTORICAL
J238_201304
This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.
Standard

Nut and Conical Spring Washer Assemblies

2017-05-30
CURRENT
J238_201705
This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.
Standard

Steel Self-Drilling Tapping Screws

2014-09-09
WIP
J78
This SAE Standard covers the dimensional and general specifications, including performance requirements, for carbon steel self-drilling tapping screws suitable for use in general applications. It is the objective of this document to insure that carbon steel self-drilling tapping screws, by meeting the mechanical and performance requirements specified, shall drill a hole and form or cut mating threads in materials into which they are driven without deforming their own thread and without breaking during assembly. Appendix A is included to provide a recommended technique for measuring the case depth on the screws.
Standard

Tension Indicating Washer Tightening Method for Fasteners

2013-04-15
HISTORICAL
J2486_201304
This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.
Standard

Tension Indicating Washer Tightening Method for Fasteners

2018-04-24
CURRENT
J2486_201804
This SAE Recommended Practice covers installation and inspection methods for fasteners which are tensioned using Tension Indicating Washers (TIWs) as a means to ensure that adequate tension is developed in mechanically fastened joints. Figure 1 depicts a typical TIW, and Figure 2 depicts a fastener assembly with a TIW before and after tensioning.
Standard

Test Methods for Metric Threaded Fasteners

1999-07-20
CURRENT
J1216_199907
This standard establishes procedures for conducting tests to determine the mechanical properties of externally and internally threaded fasteners. Property requirements and the applicable tests for their determination are specified in individual product standards. In those instances where the testing requirements are unique or at variance with these standard procedures, the product standard shall specify the controlling testing requirements. This standard describes mechanical tests for determining the following properties: For externally threaded fasteners: Product hardness (Section 4.1) Surface hardness (Section 4.2) Proof load (Section 4.3) Yield strength (Section 4.4) Axial tensile strength (Section 4.5) Wedge tensile strength (Section 4.6) Elongation (Section 4.7) Reduction of area (Section 4.7) For internally threaded fasteners: Product hardness (Section 5.1) Proof load (Section 5.2)
X