Refine Your Search

Search Results

Standard

Bolt and Capscrew Sizes for Use in Construction and Industrial Machinery

1994-06-01
HISTORICAL
J370_199406
This SAE Recommended Practice covers the use of preferred bolt and capscrew sizes, wherever applicable, on construction and industrial machinery to ease serviceability. Designers, in their efforts to determine the proper fastener for heavy equipment, sometimes overlook the practical aspects of serviceability. When a particular component requires frequent service, it is much faster and easier for the serviceman to work with common size, easily distinguished bolts and capscrews which require a minimum of tools. Section 4 lists eight diameters of recommended bolts and capscrews, some of which can be found in any hardware store, require only standard tools, are easy to distinguish, and at the same time cover proof loads from 1043 kg (2300 lb) on up at convenient intervals. While some applications may require other sizes and/or fine threaded fasteners for greater camping forces and/or area restrictions, the convenience of UNC threads in the sizes indicated is preferred wherever possible.
Standard

Bolt and Capscrew Sizes for Use in Construction and Industrial Machinery

1998-05-01
HISTORICAL
J370_199805
This SAE Recommended Practice covers the use of preferred bolt and capscrew sizes, wherever applicable, on construction and industrial machinery to ease serviceability. Designers, in their efforts to determine the proper fastener for heavy equipment, sometimes overlook the practical aspects of serviceability. When a particular component requires frequent service, it is much faster and easier for the serviceman to work with common size, easily distinguished bolts and capscrews which require a minimum of tools. Section 4 lists eight diameters of recommended bolts and capscrews, some of which can be found in any hardware store, require only standard tools, are easy to distinguish, and at the same time cover proof loads from 1043 kg (2300 lb) on up at convenient intervals. While some applications may require other sizes and/or fine threaded fasteners for greater camping forces and/or area restrictions, the convenience of UNC threads in the sizes indicated is preferred wherever possible.
Standard

Bolt and Capscrew Sizes for Use in Construction and industrial machinery

1968-11-01
HISTORICAL
J370_196811
This SAE Recommended Practice covers the use of preferred bolt and capscrew sizes, wherever applicable, on construction and industrial machinery to ease serviceability. Designers, in their efforts to determine the proper fastener for heavy equipment, sometimes overlook the practical aspects of serviceability. When a particular component requires frequent service, it is much faster and easier for the serviceman to work with common size, easily distinguished bolts and capscrews which require a minimum of tools. Section 4 lists eight diameters of recommended bolts and capscrews, some of which can be found in any hardware store, require only standard tools, are easy to distinguish, and at the same time cover proof loads from 1043 kg (2300 lb) on up at convenient intervals. While some applications may require other sizes and/or fine threaded fasteners for greater camping forces and/or area restrictions, the convenience of UNC threads in the sizes indicated is preferred wherever possible.
Standard

CONICAL SPRING WASHERS

1998-05-01
HISTORICAL
J773_199805
This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.
Standard

Conical Spring Washers

2016-08-31
CURRENT
J773_201608
This SAE Standard covers dimensional, material, and general specifications and methods of test for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.
Standard

Decarburization in Hardened and Tempered Unified Threaded Fasteners

2013-01-02
CURRENT
J121_201301
This SAE Recommended Practice covers methods for measuring, classifying, and specifying decarburization in the threaded section of hardened and tempered steel bolts, screws, studs, and similar parts. It is not intended to cover products which are specifically carburized to achieve special properties.
Standard

Hex Bolts

1990-01-01
CURRENT
J105_199001
Included herein are complete general and dimensional data for the various types of square and hex bolts recognized as SAE Standard and commonly used in automotive and other ground based motor vehicles and industrial equipment. Also included are appendixes covering wrench openings for bolts and thread runout sleeve gages. The inclusion of dimensional data in this standard is not intended to imply that all of the products described are stock production sizes. Users are requested to consult with manufacturers concerning lists of stock production sizes.
Standard

Hi Head Finished Hex Bolts

1969-06-01
HISTORICAL
J871_196906
Included herein are the detailed general and dimensional specifications applicable to hi-head finished hex bolts. All general specifications and dimensions not shown shall conform to those applicable to finished hex bolts in Table 4 of SAE J104. Hi-head finished hex bolts are primarily intended for use in the heavy construction and industrial equipment industry. The increase in head height over that of the finished hex bolt assures good wrenchability where frequent servicing is necessary, where high torquing is a requirement, or where wear on the bolt head is a problem.
Standard

High and Low Crown (Blind, Acorn) Hex Nuts

2016-11-18
CURRENT
J483_201611
Included in this SAE Recommended Practice are complete general and dimensional data for the high and low types of crown nuts recognized as SAE Standard. These nuts are primarily intended for application in automotive and other ground-based motor vehicles and industrial equipment to provide an ornamental or protective closure over end of bolts, studs, or screws.
Standard

Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins

2016-11-18
CURRENT
J485_201611
SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.
Standard

Holes in Bolt and Screw Shanks and Slots in Nuts for Cotter Pins

2013-04-16
HISTORICAL
J485_201304
SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2019-11-12
WIP
J429
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

1971-06-01
HISTORICAL
J429F_197106
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

1977-07-01
HISTORICAL
J429J_197707
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

1977-07-01
HISTORICAL
J429I_197707
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2011-09-08
HISTORICAL
J429_201109
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts used in automotive and related industries in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. 1.1 The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2014-05-07
CURRENT
J429_201405
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems1, and U-bolts2 in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
Standard

Mechanical and Material Requirements for Externally Threaded Fasteners

2013-04-29
HISTORICAL
J429_201304
This SAE Standard covers the mechanical and material requirements for inch-series steel bolts, screws, studs, screws for sems , and U-bolts in sizes to 1-1/2 in. inclusive. The term “stud” as referred to herein applies to a cylindrical rod of moderate length threaded on either one or both ends or throughout its entire length. It does not apply to headed, collared, or similar products which are more closely characterized by requirements shown herein for bolts. The mechanical properties included in Table 1 were compiled at an ambient temperature of approximately 20 °C (68 °F). These properties are valid within a temperature range which depends upon the material grade used and thermal and mechanical processing.
X