Search Results

A fleet of 50, 1986-1987 model year cars designed for unleaded gasoline has been tested on the road and on a chassis dynamometer over 5 driving cycles and a wide range of other manoeuvres including steady speeds. It was found that the fuel consumption of this fleet was 17 to 23% (depending on test cycle) less than that of a corresponding fleet to leaded fuelled cars of 1980 model year average. Exhaust emissions were significantly lowered in the range of 45 to 93%. However trend line analysis of the several data sets indicates that the ULG fleet has about 6% higher fuel consumption than would have been expected if there had been a continuing evolution of leaded vehicle technology. The data base produced has applicability to a wide range of planning and design tasks, and those illustrated indicate the effects of speed limit changes and advisory speed signs on fuel consumption and emissions.

New concepts in oxygen enrichment of the inlet air have been examined in tests on two direct injection diesel engines, showing: significant reduction in particulate emissions (nearly 80% at full load), increased thermal efficiency if injection timing control is employed, substantial reductions in exhaust smoke under most conditions, ability to burn inferior quality fuels which is economically very attractive and achivement of turbo-charged levels of output with consequential benefits of increased power/mass and improved thermal efficiency. The replacement of an engine's turbocharger and intercooling system with a smaller turbocharger and polymeric membrane elements to supply the oxygen enriched stream should allow improved transient response. NOx emission remain a problem and can only be reduced to normally aspirated engine levels at some efficiency penalty.

An adaptive air fuel ratio (AFR) control system has been implemented on a modern high performance fuel injected four cylinder engine. A pressure transducer in the combustion chamber is used to measure the indicated mean effective pressure (IMEP) for efficiency and cyclic variability feedback. The controller tunes the relative AFR, λ, in the range λ = 1 to λ = 1.5, to maximise the thermal efficiency in real time. The system adaptively accounts for changes in operating conditions such as ambient temperatures and user demands. The IMEP feedback allows the closed loop control system to update every few revolutions with short tune in times in the order of seconds. Open and closed loop test results are presented, demonstrating the incremental efficiency gains over fixed or mapped AFR control. The system continually adjusts the fuelling for maximum efficiency given its constraints and provides a basis for optimisation of future lean burn technologies.

This paper presents a combined experimental and numerical method for analysing energy flows within a spark ignition engine. Engine dynamometer data is combined with physical models of in-cylinder convection and the engine's thermal impedances, allowing closure of the First Law of Thermodynamics over the entire engine system. In contrast to almost all previous works, the coolant and metal temperatures are not assumed constant, but rather are outputs from this approach. This method is therefore expected to be most useful for lean burn engines, whose temperatures should depart most from normal experience. As an example of this method, the effects of normalised air-fuel ratio (λ), compression ratio and combustion chamber geometry are examined using a hydrogen-fueled engine operating from λ = 1.5 to λ = 6. This shows large variations in the in-cylinder wall temperatures and heat transfer with respect to λ.

A validated model which attributes fuel consumption to 11 components of a vehicle's energy loss, has been applied to investigate the benefits from improvements in design parameters which can reduce fuel use. Sensitivity analysis of a large, family sized car, gives the ranked order of design variables for improving fuel consumption as: vehicle mass, idle fuel rate or engine friction (or both) and rolling resistance for urban driving. Amongst the remaining parameters aerodynamic drag is lowly ranked but, in highway driving, it ranks first along with vehicle mass and rolling resistance, thus indicating that the proportion of urban to highway driving, which will vary from country to country is important. Driving conditions should be optimised along with vehicle design for best energy conservation and greenhouse gas mitigation.

The specific power densities and therefore the level of sophistication and costs of FIM-MOTOGP engines 800 cm3 in capacity have reached levels similar to those of the traditionally much more expensive FIA-Formula One engines and some racing developments have no application at all in the development of production bikes. The aim of the paper is therefore to review FIM-MOTOGP engine rules and make recommendations that could reduce costs and make racing more directly relevant to the development of production bikes while enhancing the significant interest in technical innovation by the sports' fans.

This paper compares the performance of a small two cylinder, 430 cm3 engine which has been tested in a variety of normally aspirated (NA) and forced induction modes on 98-RON pump gasoline. These modes are defined by variations in the induction system and associated compression ratio (CR) alterations needed to avoid knock and maximize volumetric efficiency (ηVOL). These modes included: (A) NA with carburetion (B) NA with port fuel injection (PFI) (C) Mildly Supercharged (SC) with PFI (D) Highly Turbocharged (TC) with PFI The results have significant relevance in defining the limitations for small downsized spark ignition (SI) engines, with power increases needed via intake boosting to compensate for the reduced swept volume. Performance is compared in the varying modes with comparisons of brake mean effective pressure (BMEP), brake power, ηVOL, brake specific fuel consumption (BSFC) and brake thermal efficiency (ηTH).

This paper compares the performance, efficiency, emissions and combustion parameters of a prototype two cylinder 430 cm3 engine which has been tested in a variety of normally aspirated (NA) modes with compression ratio (CR) variations. Experiments were completed using 98-RON pump gasoline with modes defined by alterations to the induction system, which included carburetion and port fuel injection (PFI). The results from this paper provide some insight into the CR effects for small NA spark ignition (SI) engines. This information provides future direction for the development of smaller engines as engine downsizing grows in popularity due to rising oil prices and recent carbon dioxide (CO2) emission regulations. Results are displayed in the engine speed, manifold absolute pressure (MAP) and CR domains, with engine speeds exceeding 10000 rev/min and CRs ranging from 9 to 13. Combustion analysis is also included, allowing mass fraction burn (MFB) comparison.

This paper describes the design and development of a gasketless interface, which was used successfully to couple an aluminium cylinder head to an open deck design cylinder block. The cylinder block was manufactured from aluminium, featuring shrink fit dry cast iron liners. Extensive CAE modelling was employed to implement the gasketless interface and thus avoid using a conventional metal or fiber based cylinder head gasket. The engine was specifically designed and configured for the purpose, being a 430 cm3, highly turbocharged (TC) twin cylinder in-line arrangement with double overhead camshafts and four valves per cylinder. Most of the engine components were specially cast or machined from billets. The new design removed the conventional head gasket and relied on the correct amount of face pressure generated by interference between the cylinder head and block to seal the interface. This had advantages in improving the structural integrity of the weak open deck design.

This is the second part of a two-part study that compared the degree of deterioration of catalytic converters taken from vehicles with low and high odometer readings. Part two details the catalytic performance characteristics of the catalysts that were physically characterised, according to chemical contamination and thermal degradation, previously in part one. The catalytic activity was determined using engine dynamometer and laboratory tests. The low odometer catalysts showed largely uniform light-off temperatures for CO, HC and NO that were increased in the order of 20 % relative to a new catalyst. The steady state activity was largely unaffected. The dominant deactivation mechanism of these catalysts was found to be the baseline thermal deterioration of the alumina washcoat under normal vehicle operating conditions. The deactivation shown in the high odometer catalysts was highly varied with the greatest loss of activity resulting from exposure to severe thermal conditions.

The degree of physical deterioration of catalytic converters removed from two groups of motor vehicles with low and high odometer readings have been studied. The changes in the physical and chemical properties between the two catalyst groups were investigated using the XRD, BET and PIXE/PIGE techniques. Thermal damage was the main catalyst deterioration mechanism in both odometer groups. The low odometer group showed near-uniformity in both surface area loss (average 45 %) and degree of CeO2 sintering representing the baseline thermal deterioration from normal vehicle operation. High odometer catalysts displayed more complex deactivation mechanisms involving both chemical contamination and thermal deactivation such as support phase transformation, internal “hot zones” and contaminant-support interactions.

This paper describes the design and development of an engine with constant power for SAE's student Formula race-car competition, allowing the avoidance of gear shifting for much of the Autocross event. To achieve constant power for over 50% of the speed range, turbocharging was adopted with a boost pressure ratio of 2.8 at mid-range speeds and applied to an engine capacity of 430 cc. This engine was specifically designed and configured for the purpose, being a twin cylinder in-line arrangement with double overhead camshafts. Most of the engine components were specially cast or machined from billets. The capacity was selected to minimise frictional losses and thus increase delivered power along with dry sump lubrication and a three speed gear box. The engine manifolds and plenums were designed using a CAE application and proved to be well suited to the task resulting in excellent agreement between predicted and actual performance.

This paper presents some of the modelling and experimental work being carried out at the University of Melbourne, in collaboration with CMC Research, on their new Scotch yoke engine concept. It begins with an overview of the engine, its compactness and friction advantages. The development of a one dimensional ‘squeeze film’ model is outlined and some simulation results are presented for both a motored and fired engine. A novel feature of the model is the introduction of an ‘un-filled factor’ to account for the dynamics of the oil film volume particular to this type of linear bearing. Experimental results are presented to highlight the important features and serve as a means of validating the model predictions. Comparisons show that the squeeze model correlates reasonably well with the experimental data and it is concluded that the current, flat, bearing design works by a predominantly squeeze film mechanism.

Increasing engine power and efficiency using a particle swarm optimization technique is investigated by using thermodynamics based quasi-steady engine simulation model. A simplified engine friction model is also incorporated to estimate the brake power output. Further, a simple knock model is used to make sure of knock free engine operation. Model is calibrated and validated to a Ford Falcon AU six-cylinder gasoline engine. Nine different engine-operating parameters are considered as input variables for the optimization; spark timing, equivalence ratio, compression ratio, inlet and exhaust vale opening timing and durations, maximum inlet valve lift and manifold pressure. Significant improvement of the engine power output for a given amount of induced gas is observed with the optimized conditions when compared to the corresponding power output with the reference engines normal operating conditions.

In this paper the experimental performance of the lean limits is examined for two different types of engines the first a dedicated LPG high compression ratio 2-valve per cylinder engine (Ford of Australia MY 2001 AU Falcon) and the second a gasoline moderate compression 4-valve per cylinder variant of the same engine (Ford of Australia MY 2006 BF Falcon). The in-cylinder composition at the lean limit over a range of steady state operating conditions is estimated using a quasi-dimensional model. This makes it possible to take into account the effects of both residual fraction and fresh charge diluents (EGR and excess air) that allow the exploration of a modeled lean limit performance [1, 2]. The results are compared to the predictions from a model for combustion variability applied to the quasi-dimensional model operating in optimization mode.

Gas assisted jet ignition is an advanced prechamber ignition process that allows ignition of ultra lean mixtures in an otherwise standard spark ignition engine. The results presented in this paper indicate that in a gas assisted jet ignition system fuelled with LPG in both the main chamber and prechamber, the lean limit can be extended to between λ = 2-2.35, depending on the load and speed. Although the fuel combinations that employ H2 as the prechamber fuel can extend the lean limit furthest (λ = 2.5-2.6), the extension enabled by the LPG-LPG prechamber-main chamber combination provides lower NOx emission levels at similar λ. In addition, when LPG is employed in place of gasoline as the main chamber fuel, hydrocarbon emissions are significantly reduced, however with a slight penalty in indicated mean effective pressure due to the gaseous state of the LPG.

This paper describes the turbocharger development of a restricted 430 cm3 odd firing two cylinder engine. The downsized test engine used for development was specifically designed and configured for Formula SAE, SAE's student Formula race-car competition. A well recognised problem in turbocharging Formula SAE engines arises from the rules, which dictate that the throttle and air intake restrictor must be on the suction side of the compressor. As a consequence of upstream throttling, oil from the compressor side seal assembly is drawn into the inlet manifold. The development process used to solve the oil consumption issue for a Garrett GT-12 turbocharger is outlined, together with cooling and control issues. The development methodology used to achieve high pressure ratio turbocharging is discussed, along with exhaust manifold development and operating limitations. This includes experimental and modeling results for both pulse and constant pressure type turbocharging.

This paper describes the mechanical component design, lubrication, tuning and control aspects of a restricted, odd fire, highly turbocharged (TC) engine for Formula SAE competition. The engine was specifically designed and configured for the purpose, being a twin cylinder inline arrangement with double overhead camshafts and four valves per cylinder. Most of the engine components were specially cast or machined from billets. A detailed theoretical analysis was completed to determine engine specifications and operating conditions. Results from the analysis indicated a new engine design was necessary to sustain highly TC operation. Dry sump lubrication was implemented after initial oil surge problems were found with the wet sump system during vehicle testing. The design and development of the system is outlined, together with brake performance effects for the varying systems.

A high compression ratio, single cylinder, open chamber diesel engine was converted to operate on homogenously charged compressed natural gas (CNG) with the aim of minimising pollutant emissions such as oxides of nitrogen, particulate matter and carbon dioxide. Three ignition systems were tested including spark ignition (SI), diesel pilot ignition (DPI) and hydrogen assisted jet ignition (HAJI). Irrespective of ignition system used, the efficiency of the engine operating on CNG was significantly reduced at part load compared to diesel. This was predominantly due to a greater amount of unburnt hydrocarbons, higher cycle-by-cycle variability, slow and partial burns and increased heat transfer to the walls. DPI and HAJI systems were able to extend the lean limit to lambda 2.7 and 3.3 respectively, however this did not result in efficiency gains.

Favorable and unfavorable properties of hydrogen as a combustion engine fuel have been accommodated in a design of a fuel efficient and clean engine providing similar to gasoline maximum torque and power. The advanced H2ICE being developed is a turbocharged engine fitted with cryogenic port hydrogen fuel injection and the hydrogen assisted jet ignition (HAJI). The combustion chamber is designed to produce a high compression ratio and therefore high thermal efficiency. A waste gated turbocharger provides pressure boosting for an increased power density running ultra lean for SULEV operation without after treatment. Thanks to the combustion properties of hydrogen further enhanced by the HAJI system, the engine load is mainly controlled throttle-less decreasing the fuel-to-air equivalence ratio from ultra lean ϕ=0.43 to ultra-ultra lean ϕ=0.18. The computational model developed for addressing the major design issues and the predicted engine performance and efficiency maps are included.