Search Results

Vehicles running in wet conditions may experience hydroplaning of one or more tires. Hydroplaning can, and often does, change vehicle braking, acceleration and handling characteristics dramatically. Proper analysis of this behavior requires accommodating the clearing of paths for the rear tires that may result from the front tires engaging the water-coated surface first. In this work, tire overlap is calculated for vehicles in steady-state cornering maneuvers for generalized vehicle dimensions and tire characteristics.

An experimental program to measure braking characteristics developed under emergency braking conditions by ABS-equipped vehicles was designed and performed. Variables examined included initial braking speed, vehicle type, tire pressure and data recording equipment utilized. All experiments were conducted on a closed airport taxiway constructed of sharp, brushed and heavily striated concrete. Tests were conducted with and without activated ABS systems on the test vehicles. Results showed that (1) with the ABS activated, faint roadway markings were visible only under a very few special circumstances, (2) tire/road μ-values and corresponding deceleration values varied only slightly for differing speeds and ABS conditions, (3) tire pressure made little difference in limited test results, and (4) there were differences in recorded results depending on the equipment used for data acquisition.

Enthusiasts, accident reconstructionists and racing personnel have always been interested in wheel torque and HP values for vehicles. Modifications to the engine and/or driveline cause factory data to be in error, and special racing engines have no such data available in any case. Engine dynamometers provide useful information, but require the engine to be removed from the car before any testing can occur. Of more interest, particularly in competition situations, is the effect of changes at the driving wheels. We focus here on a simple method of deriving rim torque and HP values from accelerometer data. The data can be acquired using nearly any sufficiently accurate accelerometer package, and the calculations involved can be done by hand or with a spreadsheet program. Unknown vehicle characteristics can be extracted from coastdown tests. Use of a chassis dynamometer is not required.

Off road vehicle dynamics present fundamental differences to the engineer than those of highway vehicles. In this work, we examine off-road dynamics for a class of industrial vehicles: front-end loaders. After a review of terramechanics and off-road tire behavior, equations of motion for a front-end loader are developed. Kinematic steering relationships, steady-state performance and understeer and oversteer characteristics are also derived. Off-road front-end loader characteristics and performance in terms of vehicle handling, overturn behavior and obstacle avoidance are presented, and some design characteristics and parameter values for a typical vehicle are given to aid the designer in analysis and synthesis.

This research compares the responses of a vehicle modeled in the 3D vehicle simulation program SIMON in the HVE simulation operating system against instrumented responses of a 3-axle tractor, 2-axle semi-trailer combination. The instrumented tests were previously described in SAE 2001-01-0139 and SAE 2003-01-1324 as part of a continuous research effort in the area of vehicle dynamics undertaken at the Vehicle Research and Test Center (VRTC). The vehicle inertial and mechanical parameters were measured at the University of Michigan Transportation Research Institute (UMTRI). The tire data was provided by Smithers Scientific Services, Inc. and UMTRI. The series of tests discussed herein compares the modeled and instrumented vehicle responses during quasi-steady state, steady state and transient handling maneuvers, producing lateral accelerations ranging nominally from 0.05 to 0.5 G's.

The relatively fragile nature of racing tires, coupled with the inevitable track debris which results from racing accidents, ensures that racing drivers will routinely experience conditions involving flat tire vehicle dynamics. We define flat tire vehicle dynamics as a situation which requires the driver to provide steering and/or braking and acceleration control while the vehicle is running on one or more tires which have dramatically reduced tire pressure. In the present work, we simulate the handling and braking vehicle dynamics which occur in the presence of a single flat tire on the vehicle. The flat tire was simulated via drastically reduced cornering stiffness, partially reduced limiting frictional capability and increased rolling resistance, and was alternatively simulated on both the front and rear axle. No simulations were conducted with more than a single flat tire because multiple tire failures which do not involve an actual accident contact and/or damage are rare.

Roadway tractive capabilities are an important factor in accident reconstruction. In the absence of full-scale experiments, tire/road coefficient of friction values are sometimes quoted from reference textbooks. For the various types of road construction, the values are given only in the form of a wide range. One common roadway type is oil-and-chip construction. We examine stopping distances for newly-rocked oil-and-chip roads vs. similarly constructed roads that have been traffic-polished. The examination was conducted through full-scale braking experiments with instrumented vehicles. Results show that the differences between newly-rocked oil-and-chip roads when compared to roads that are traffic-polished are on the same order as vehicle, tire and ABS algorithm differences, and that full-scale testing is required for accurate μ-values.

Vehicles running in wet conditions may experience hydroplaning of one or more tires. Hydroplaning can, and often does, change vehicle braking, acceleration and handling characteristics dramatically. Proper analysis of this behavior requires accommodating the clearing of paths for the rear tires that may result from the front tires engaging the water-coated surface first. In this work, a hydroplaning analysis is presented that examines steady-state cornering under potential hydroplaning situations and includes lateral weight transfer, tire load sensitivity and path clearing potential. The sensitivity of vehicle understeer/oversteer characteristics to path clearing and vehicle dimensional characteristics is also examined.

The type of differential used in a vehicle has an important and often-neglected effect on handling performance. This is particularly important in racing applications, such as in IndyCar racing, in which the type of differential chosen depends on the course being raced (superspeedway ovals, short ovals, temporary street courses and permanent road courses). In the present work, we examine the effect of a locked rear differential on oversteer/understeer behavior. Using a linear tire model, it is shown that employing a locked differential adds a constant understeer offset to the steering wheel angle (SWA) -v- lateral acceleration vehicle signature. A computer simulation of steady-state cornering behavior showed that the actual effect is much more complicated, and is strongly influenced by static weight distribution, front/rear roll couple distribution, available traction and the radius of the turn being negotiated.

Recent research on the effects of tire hydroplaning has examined the hydroplaning phenomenon and its potential effects on vehicle maneuvering from (1) geometric, (2) straight line braking/acceleration and (3) steady-state cornering maneuver points of view. In this work, we focus on the potential for hydroplaning during a transient maneuver: a standardized double lane change maneuver (ISO3888-1). Using both closed-form calculations and the HVE software suite, it is shown that partial hydroplaning has only a small-to- moderate potential to occur during portions of such maneuvers, but is not likely throughout the entire duration of the maneuver.

Bicycle accidents may occur in the presence of roadway asperities, discontinuities and other pavement failure modes and conditions. We examine the dynamics of ramp-climbing and potential pitchover by the rider when idealized asperities are encountered from a theoretical point of view, and derive an expression for the speed at which pitchover will occur if and when a sudden stop occurs. A series of experiments was carried out in which road bicycle behavior was examined for idealized roadway asperities of known size and configuration. Finally, a series of braking experiments was performed to determine the emergency stopping potential of a road bicycle.